Sentiotec IS1 P-IS1-T Manuel utilisateur
Version 04/23 Ident-Nr. 1-026-216
EN
DE
INSTRUCTIONS FOR INSTALLATION AND USE
English
36
Infrared control unit
IS1
P-IS1-T
Table of Contents
1. About this instruction manual 3
2. Important information for your safety 4
2.1. Intended use 4
2.2. Safety information for the installer 5
2.3. Safety information for the user 6
3. Product description 7
3.1. Scope of delivery 7
3.2. Optional accessories 7
3.3. Product functions 7
4. Installation 8
4.1. Preparing for surface mounting 8
4.2. Preparing for recess mounting 9
4.3. Preparing the housing 9
5. Electrical connection 10
5.1. Removing the front cover 12
6. Final assembly 13
6.1. Final assembly - surface mounting 13
6.2. Final assembly - recess mounting 14
6.3. Fitting the sensor 15
7. Adjusting the heating time limit 16
8. Operation 17
8.1. Operating and display elements 17
8.2. Quick start 18
8.3. Description of the functions and control elements 19
9. Troubleshooting 21
10. Disposal 22
11. Technical data 22
EN
Instructions for installation and use p. 3/22
1. About this instruction manual
Read these installation and operating instructions carefully and keep them within
reach when using the infrared control unit. This ensures you can refer to informa-
tion about safety and operation at any time.
Symbols used for warnings
These installation and operating instructions feature warning symbols next to
activities presenting a hazard to the user. Warning symbols must be observed
at all times. This prevents damage to property and injuries, which in the worst
case may be fatal.
The warning symbols contain keywords with the following meanings:
DANGER!
Serious or fatal injury will occur if this warning symbol is not observed.
WARNING!
Serious or fatal injury may occur if this warning symbol is not observe.
CAUTION!
Minor injuries may occur if this warning symbol is not observed.
ATTENTION!
This keyword is a warning that damage to property may occur.
Other symbols
This symbol indicates tips and useful information.
The current installation and operating instructions can also be found in
the downloads section of our website: www.sentiotec.com/downloads.
Instructions for installation and use p. 4/22
2. Important information for your safety
The IS1 infrared control unit has been produced in accordance
with the safety regulations applicable for technical units. However,
hazards may occur during use. You should therefore adhere to
the following safety information and the specic warnings in the
individual chapters.
2.1. Intended use
The IS1 infrared control unit is used to control and regulate the
interior temperature and to operate the cabin light. The infrared
control unit may only be used for controlling one heating circuit with
a maximum capacity of 3.0 kW.
Suitable infrared heaters: DIR-350-R, WIR-350-R, DIR-500-R,
WIR-500-R, DIR-750-R, WIR-750-R, DIR-1300-R, WIR-1300-R,
ECO-350-R, ECO-350-G, ECO-500-R, ECO-500-G, ECO-750-R,
O-IRC-W
Suitable infrared plates: IR-WP-175, IR-WP-100, IR-WP-390, IR-
WP-510, IR-WPHL-510, IR-WPHL-100, IR-WPHL-390, IR-WPHL-175
►Only in connection with the optional P-ISX-FF foil sensor.
Any use exceeding this scope is considered improper. Improper
use can result in damage to the product, severe injuries or death.
EN
Instructions for installation and use p. 5/22
2.2. Safety information for the installer
●Installation may only be performed by a qualied electrician or
similarly qualied person.
●Installation and connection of the infrared control unit may only
be performed when the power supply is disconnected.
●The temperature sensor must be mounted in such a way that
ensures it is unaected by the inow of air.
●Observe all regulations applicable at the installation location.
●For your own safety, consult your supplier in the event of prob-
lems that are not explained in sucient detail in the installation
instructions.
Instructions for installation and use p. 6/22
2.3. Safety information for the user
●The device must not be used by children under 8 years old.
●The device may only be used by children over 8 years old, by
persons with limited psychological, sensory or mental capabili-
ties or by persons with lack of experience/knowledge under the
following conditions:
– When they are supervised.
– When they have been shown how to use the device safely
and are aware of the hazards that could occur.
●Children must not play with the device.
●Children under 14 years old may only clean the device if they
are supervised.
●For health reasons, do not use the infrared cabin if you are under
the inuence of alcohol, medication or drugs.
●Make sure that no ammable objects have been placed on or
in front of the infrared heater or infrared heat plate before the
infrared control unit is switched on.
●For your own safety, consult your supplier in the event of prob-
lems that are not described in sucient detail in the operating
instructions.
EN
Instructions for installation and use p. 7/22
3. Product description
3.1. Scope of delivery
●IS1 infrared control unit
●1.6 m mains connection cable
●1.5 m room sensor with silicone cable
●Installation material
●Instructions for installation and use
3.2. Optional accessories
●IR-IS-A03 Adapter cable for heaters and heat plates (0.3 m)
●IR-IS-A25 Adapter cable for heaters and heat plates (2.5 m)
●IR-1P2 T-splitter, 2-way
●IR-1P3 Splitter, 3-way
●IR-1P5 Splitter, 5-way
●P-ISX-FF Foil sensor incl. 3 m cable
●P-ISX-FUSE Fine fuse connection for light
●O-F2 Room sensor
3.3. Product functions
The IS1 infrared control unit is used to regulate the cabin temperature using a
room sensor. Settings can be made for the target temperature, duration and light
using the operating elements. The current temperature is shown on the display.
1 heating circuit for a max. capacity of 3.0 kW enables the connection of infrared
heaters and infrared heat plates.
Installation instructions, only for experts p. 8/22
4. Installation
The infrared control unit can either be surface-mounted or recess mounted.
4.1. Preparing for surface mounting
To mount the control unit on a surface, you need to make cable bushings in the
cabin wall. Refer to the following gure for the positions.
49
85
17,5
34
49
65
80,5
1
7
2 3 4 5 6
1 Sensor cable outlet
2 Mains power line
3 Heater/foils outlet
4 Free
5 Free
6Light outlet
7 Cable shaft
►Caution: If the cable is fed down-
wards through the cable shaft 7, the
sensor cable must be tted with ad-
ditional protective insulation.
EN
Installation instructions, only for experts p. 9/22
4.2. Preparing for recess mounting
Mounting the control unit in a recess requires a cut-out section.
●Cut-out section size: 160 mm x 102 mm
●Mounting depth: 39.5 mm
4.3. Preparing the housing
102 mm
160 mm
R=5 mm
►Ensure that the control unit
has sucient rear ventilation!
Work on the housing must only be carried out using a standard screw-
driver. Using a cordless screwdriver may cause irreparable damage to
the housing.
●Remove the four screws in the housing 1.
●Take the cover 2 o the control unit.
●Loosen the strain reliefs 3.
1
2
3
Installation instructions, only for experts p. 10/22
5. Electrical connection
Before mounting the control unit, the electrical connections must be completed.
Observe the following points when connecting the power:
●Installation may only be performed by a qualied electrician or similarly quali-
ed person.
●Make sure that the connection cables are properly tted in the terminals. Poorly
tted cables heat up quickly and can result in irreparable damage and re.
N
L
PE
230V 1N ~ 50Hz
16A
3
L N U N
3
N L
ww
rw
3
2
wr bb
bb
2
max. 200W
Mains
Heating system
max. 3.0 kW
Light
Room sensor
Optional foil
sensor
Table des matières
Langues :
Autres manuels Sentiotec Unité de contrôle
Sentiotec
Sentiotec IS1 Manuel utilisateur
Sentiotec
Sentiotec Pro D Manuel utilisateur
Sentiotec
Sentiotec Pro C2 Manuel utilisateur
Sentiotec
Sentiotec Pro B2 Manuel utilisateur
Sentiotec
Sentiotec Wave.com4 infra Manuel utilisateur
Sentiotec
Sentiotec Infrabox basic S Mode d’emploi
Sentiotec
Sentiotec K1 Next Manuel utilisateur
Sentiotec
Sentiotec Pro B2 Manuel utilisateur
Sentiotec
Sentiotec just sauna fin Manuel utilisateur
Sentiotec
Sentiotec PRO-B3 Manuel utilisateur
Sentiotec
Sentiotec CK 41 Manuel utilisateur
Sentiotec
Sentiotec IHS 1 Manuel de la liste des pièces
Sentiotec
Sentiotec IS2 Manuel utilisateur
Sentiotec
Sentiotec A2 Manuel utilisateur
Sentiotec
Sentiotec Pro-C2 Manuel utilisateur
Sentiotec
Sentiotec Pro C3 Manuel utilisateur
Sentiotec
Sentiotec Pro C3 Manuel utilisateur
Sentiotec
Sentiotec A2 Manuel utilisateur
Sentiotec
Sentiotec Karibu Modern FinnischPlug'n'Play Manuel utilisateur
Sentiotec
Sentiotec Pro B Manuel utilisateur
Manuels Unité de contrôle populaires d'autres marques
Festo
Festo Compact Performance CP-FB6-E Manuel de la liste des pièces
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur
JS Automation
JS Automation MPC3034A Manuel utilisateur
JAUDT
JAUDT SW GII 6406 Series Guide rapide
Spektrum
Spektrum Air Module System Manuel utilisateur
BOC Edwards
BOC Edwards Q Series Manuel utilisateur
