Seiler Evolution xR6 Manuel utilisateur

PRECISION MICROSCOPES

EVOLUTION XR6

LED Dental Microscope Slim Model

User’s Manual

Table of Contents

Table of Contents 2

Installaon & Assembly 3

LED Illuminaon Instrucons 8

LED Warranty 13

Interpupillary Distance Adjustment 13

Parfocalizing 14

The Color Filter and Cleaning 15

Dimensions 16

Parts Breakdown 17

Installaon & Assembly

1. Remove the base from the box and set base

boom up (casters facing up) on the cardboard

or foam from the box for cushion.

2. Remove the base weights from the weights box

and insert the weights one at a me into the

boom of the base.

Align the pins with the holes and depress the

thumb lock buon to put the weights into place.

Flip the base over so that the top center post is

facing upward.

* Be sure to check to make sure that the

weights are secured before ipping the base

over.

3. Remove the pole from the packaging and insert pole into the center post hole in the base. Align the two

indenon marks in the pole to the holes in the base center post hole collar.

4. Once the pole is secured into the base, insert the Light Housing/Light Source poron of the microscope

into the top of the pole. This is where the illuminaon system is housed. Make sure that the light source is

secured while inserng the light source into the pole.

Once the pole is in the collar and indenons are

aligned, use the provided Allen Wrench to ghten

the two Allen bolts in the base center post collar to

secure the pole.

5. Next insert the Pantographic Arm into the light

source arm.

6. Place the Liquid Light Guide cable through the

boom cover.

7. Aer the Pantographic Arm is inserted and the Liquid Light Guide cable is secure, add the extension piece

into the top of the Pantographic Arm on the under side. Be sure to loosen the black knob and pull plunger on

the Pantographic Arm in order to insert the extension arm. Screw on the white locking knob.

Plunger

8. Next, insert the 45 degree coupler into the extension arm. Screw down the white locking knob.

9. Insert the Angle Arm into the 45 degree coupler coming o the opc pod. Screw down the white knob.

10. Insert the Liquid Light Guide cable into the light port opening on the Opcal Pod.

11. Secure the Binocular Head onto the Opcal Pod by ghtening the thumb screw.

Thumb Screw

PANTOGRAPHIC ARM BALANCING

NOTE: Pantographic Arm may need tension

adjusted (black knob on top, turn counter-

clockwise to add tension, clockwise to release

tension). This may need to be done if camera/

video are added to the scope. This will increase

or decrease the tension to desired funcon for

user. The Pantographic Arm may have to be in the

horizontal posion to make adjustments.

Tension Knob

LED Illuminaon Instrucons

1. INTRODUCTION

Congratulaons on the purchase of your new SSL-2000 Light Source! This user-friendly LED light source is a high

eciency light source ulizing state of-the-art superior illuminaon technology. It oers a variety of features such as:

• 6500º K daylight brightness for good color denion

• Quiet operaon

• Long life, 50,000 hrs.

• Compact and light weight

• Pulse-width Modulaon (PWM) Electrical Dimming

This secon of the manual will help you to install the device and opmally integrate it with other components of

your system. It will also instruct you how to operate the LED Light Source and how to keep it clean. It will give you

maintenance and service guidelines as well as recommendaons for best performance results.

1.1 INDICATIONS FOR USE: The LED Light Source is used to illuminate the site of surgery during minimally invasive

surgical procedures. The light is transmied from the light source through a ber opc cable and a scope.

2. WARNINGS

To prevent re or electric shock, do not open or expose the LED light source unit to rain or moisture. Refer all servicing to

qualied personnel only.

Not suitable for use in presence of ammable anesthec mixture with air or with oxygen or nitrate oxide.

To prevent any potenal electro-magnec interference, do not use any kind of cellular phone near the

light source.

This product should be used only with type BF endoscopic instruments which have been cered

according to IEC 601-1 for medical equipment and IEC 601-2-18 for endoscopic equipment.

Cauon: This product is not provided as sterile.

Cauon: All devices connecng to the LED Light Source must be classied as medical equipment. When

addional informaon processing equipment is connected to the LED Light Source, the operator must

determine that all equipment complies with the appropriate end-product standards (such as IEC 60950

or IEC 60065 and the Standard for Medical System, IEC 60601-1-1).

Cauon: The LED Light source can cause permanent eye damage if viewed directly with unprotected eye.

To reduce the chance of eye damage, set the intensity control always to the minimum level and plug the

ber opc cable into the unit before turning on the power.

EQUIPMENT CONNECTION

Cauon: The ber opc cable must be a NON-CONDUCTIVE CABLE. It should not have conducve

shielding or any other conducve connecon between the paent and equipment. Such connecon will

impair safety of the equipment. It must be rinsed free of soaking/disinfectant soluon and dried before

plugging into the LED light source receptacle. Ensure the opcal surface is clean before engaging into the

light source.

3. SPECIFICATIONS

Item Specicaon

Light Source Type LED (Light Eming Diode)

Power 50 Wa

Color Temperature 6500º K

Led life 50,000 hours (typical)

Light guide adapter

Brightness control PWM (Pulse-width Modulaon) – 0-100% Dimming

Input voltage 100-240V AC, 50/60 Hz

Rated Power 52 wa

Regulatory Approvals UL60601-1,CAN/CSA C22.2 No.601.1 (SUP1+AM2),EN 60601-1-2 and CE

marked

Equipment Class Class I, BF-type

Mode of Operaon Connuous operaon

Water Resistant Not Protected Equipment, IPX0

Operang Environment

Temperature

Relave Humidity

Air Pressure

+0° to +40° C (32° to 104° F)

0 to 85%rh, non condensing

700 to 1060 hPa

Storage Environment

Temperature

Relave Humidity

Air Pressure

-20° to +60° C (-4° to 140° F)

30 to 95%rh, non condensing

700 to 1060 hPa

Dimensions 4.65” W x 3.32” H x 7.25” D

Weight 2.5 lbs./1.14 kg

4. OPERATING ELEMENTS, SYMBOLS AND FUNCTIONS

4.1 FRONT PANEL

No. Name Funcon

1Power switch Turns the light source on and o. Fan will operate

2Light Guide Adapter

3Intensity Control Electronically controls the light output

4.2 REAR PANEL

Figure 2. LED Light Source Rear Panel

No. Name Funcon

1AC main inlet Accepts AC power cord

2Fuse 2A, 250V (1/4” x 1 ¼”) me delay

3Grounding Connector For potenal equalizaon

4Venng grids Allows adequate venlaon and cooling of the light

source

4.3 Boom Panel

Figure 3. LED Light Source Product Label

Autres manuels pour Evolution xR6

Table des matières

Autres manuels Seiler Microscope

Seiler

Seiler Microlux IV Manuel utilisateur

Seiler

Seiler Westlab III Manuel utilisateur

Seiler

Seiler Evolution Zoom Manuel utilisateur

Seiler

Seiler Evolution Zoom Manuel utilisateur

Manuels Microscope populaires d'autres marques

Thermo Scientific

Thermo Scientific Nicolet iN10 Mode d’emploi

National

National DC3-163 Manuel utilisateur

KERN Optics

KERN Optics OPE-1 Manuel utilisateur

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Manuel utilisateur

Prior

Prior Lux POL Manuel utilisateur

Opitec

Opitec Smartscoop 115615 Manuel utilisateur

KERN

KERN OPO-1 Manuel utilisateur

Topcon

Topcon SP-1P Manuel utilisateur

Motic

Motic PA43 Manuel utilisateur

Leica

Leica DVM5000 Guide de l'utilisateur

MshOt

MshOt MZ62 Manuel utilisateur

KERN Optics

KERN Optics OZR-5 Manuel utilisateur

VWR

VWR VisiScope 384 Series Manuel utilisateur

Nikon

Nikon ECLIPSE E200 POL Manuel utilisateur

Leica

Leica DI C800 Manuel

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manuel utilisateur

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manuel utilisateur

Olympus

Olympus SZ61 Manuel utilisateur