Sealey GA450 Manuel utilisateur

INSTRUCTIONS FOR:

CAMBER, CASTOR & KING-PIN GAUGE

Model No: ga450

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions

and properly maintained, give you years of trouble free performance.

1. SAFETY INSTRUCTIONS

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.

USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE

DAMAGE OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

2. INTRODUCTION & SPECIFICATION

Robust magnetic gauge mounts onto wheel/hub for quick accurate measurement of camber, castor angle, and kingpin inclination.

Camber gauge with fixed graduation from +5 to -5.

Adjustable caster gauge graduated +11 to -3.

Kingpin gauge graduated from 0 to 14 left to right.

Only suitable for vehicles fitted with steel wheels.

To be used in conjunction with steering turntables and rear wheel level plates.

Supplied in tough composite carry-case.

 WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this

equipment.

 Maintain the gauge in good condition (use an authorised service agent).

Replace or repair damaged parts.

 WARNING! Use the gauge on level and solid ground.

 DO NOT allow untrained persons to use the gauge.

 WARNING! When setting front-end alignment on commercial vehicles never make adjustments to drop arms or

interconnecting links. Doing so could result in serious tyre, wheel and steering problems.

Any alignment changes deemed necessary as a result of using this equipment must be made strictly in accordance with the

vehicle manufacturer’s recommendations.

 WARNING! The warnings, cautions and instructions referred to in this manual cannot cover all possible conditions

and situations that may occur. It must be understood that common sense and caution are factors which cannot be

built into this product, but must be applied by the operator.

Camber Gauge Graduation: ................+5° to -5°

Castor Gauge Graduation: ................+11° to -3°

King Pin Gauge Graduation:....................0 to 14

Magnetic Plate Ø:.....................................85mm

GA450 Issue No: 1 - 28/10/08

01284 757500

01284 703534

sales@sealey.co.uk

Sole UK Distributor

Sealey Group,

Bury St. Edmunds, Suffolk.

www.sealey.co.uk

Web

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.

IMPORTANT: No liability is accepted for incorrect use of this product.

WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.

INFORMATION: For a copy of our catalogue and latest promotions call us on 01284 757525 and leave your full name, address and postcode.

3. MEASURING CAMBER ANGLE

4. MEASURING CASTOR ANGLE

5. MEASURING KINGPIN INCLINATION

NOTE! Before use remove magnet protective plate.

Replace after use.

3.1 Drive vehicle forwards to centralise wheels.

3.2 Fit gauge in centre of vehicle wheel/hub.

3.3 Set D bubble to centre and read the position of A

bubble.

NOTE! Refer to the owner’s handbook before making any

adjustments.

NOTE! Any adjustments you make to either castor or

camber angles may affect the other, so re-check all

measurements after any adjustments have been made.

NOTE!

Try to simulate normal running conditions, ie. half a

tank of fuel and a weight similar to the driver in the front

seat.

4.1 Drive vehicle forward so front wheels are positioned on

steering turntables in the straight ahead position, rear

wheels on level plates.

4.2 Turn the front wheel to 20° out.

4.3 Fit gauge in centre of wheel/hub and set D bubble to

centre.

4.4 Set B bubble to 0 with adjusting screw and turn the

front wheel to 20° in.

4.5 Set D bubble to centre again and read the scale of B

bubble.

NOTE! Refer to the owner’s handbook before making any

adjustments.

NOTE! Any adjustments you make to either castor or

camber angles may affect the other, so re-check all

measurements after any adjustments have been made.

We recommend the use of turntables Model No. GA44

when checking the caster as this will enable you to

accurately set the wheels at 20°

5.1 Drive vehicle forward so front wheels are positioned on

steering turntables in the straight ahead position, rear

wheels on level plates.

5.2 Turn the front wheel to 20° out.

5.3 Fit gauge in centre of wheel/hub and set D bubble to

centre.

5.4 Set C bubble to 0 with adjusting screw and turn the

front wheel to 20° in.

5.5 Read scale of C bubble.

NOTE! Refer to the owner’s handbook before making any

adjustments.

GA450 Issue No: 1 - 28/10/08

Table des matières

Autres manuels Sealey Instrument de mesure

Sealey

Sealey VSE5863 Manuel utilisateur

Sealey

Sealey GA48.V2 Manuel utilisateur

Sealey

Sealey VS0566 Manuel utilisateur

Sealey

Sealey VS0563 Manuel utilisateur

Sealey

Sealey AK9638D Manuel utilisateur

Sealey

Sealey AK4565D.V2 Manuel utilisateur

Sealey

Sealey AK4013 Manuel utilisateur

Sealey

Sealey VS8196 Manuel utilisateur

Sealey

Sealey TA060 Manuel utilisateur

Sealey

Sealey TA065 Manuel utilisateur

Sealey

Sealey VS0052 Manuel utilisateur

Sealey

Sealey TA303 Manuel utilisateur

Sealey

Sealey DBG5011 Manuel utilisateur

Sealey

Sealey VS0052.V2 Manuel utilisateur

Sealey

Sealey STW701 Manuel utilisateur

Sealey

Sealey TA500 Manuel utilisateur

Sealey

Sealey AK9623EV Manuel utilisateur

Sealey

Sealey AK9637D.V2 Manuel utilisateur

Sealey

Sealey AK9623EV Manuel utilisateur

Sealey

Sealey TP956.V2 Manuel utilisateur

Sealey

Sealey TA203.V2 Manuel utilisateur

Sealey

Sealey VS212.V3 Mise à jour du firmware

Sealey

Sealey TA305 Manuel utilisateur

Sealey

Sealey AK9636D Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur