Sealey AK9623EV Manuel utilisateur
1 Internal Measure
2 Metric/Imperial Selector
3 Locking Screw
4 ABS/0 Switch
5 LCD Display
6 External Measure
7 On/Off Control
8 Zero Control
9 Battery Cover
10 Depth Measure
11 Step Measure
INSTRUCTIONS FOR:
MODEL:
AK9623EV
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTANT PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS, AND
CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE, FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO
MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.
DIGITAL VERNIER CALLIPER 0-300mm/0-12”
WARNING! Ensure Health and Safety, local authority and general workshop practice regulations are adhered to
when using tools and equipment.
DO NOT use if damaged.
Maintain calliper in good and clean condition for best performance.
Keep the work area clean, uncluttered and ensure there is adequate lighting.
Keep children and unauthorised persons away from the work area.
DO NOT use the calliper for any purpose other than for which it is designed.
DO NOT get calliper wet or use in damp or wet locations, or areas where there is condensation. Keep calliper clean
and dry using a dry cotton cloth only.
DO NOT dip or submerge the calliper in any type of liquid.
DO NOT expose calliper to bright sunlight or dust.
DO NOT disassemble. The calliper must be checked by qualified service personnel only.
DO NOT apply any voltage to the calliper i.e. with an electric marker pen.
The calliper is a precision instrument, treat with care, avoid using force and do not subject to knocks or shocks.
Use in reasonably constant temperature conditions of approximately 20°C.
When not in use, turn off and store gauge in a safe, dry, childproof location.
Hardened and tempered stainless steel digital calliper with satin finish. 11mm High figures in LCD display for ease of reading.
Metric and Imperial calibration with conversion between the two. Zero setting control allows for comparative measurement.
Supplied in carry-case.
1. SAFETY INSTRUCTIONS
2. INTRODUCTION & SPECIFICATION
Resolution 0.01mm (0.0005”)
Range 0-300mm (0-12”)
Accuracy ±0.04mm/0.001”
Functions Zero set, mm/inch select, incremental zero
Messages Flashing display = replace battery
Battery life Approx. two years (approx. one year in continuous service)
Battery LR44 - 1.5V
Operational Temperature range 0 - 40°C
1234
5
6
7 8
9
10
11
AK9623EV Issue No: 1 - 24/09/08
1. Ensure all measuring surfaces are clean and then turn on calliper by pressing on/off control. Wait at least
one second before use.
2. Loosen locking screw and close the calliper; if read-out does not show zero when in closed position,
reset by pressing zero control.
3. Select inch or mm units, as required, with the metric/imperial selector. Check that display shows the
required units.
4. Measurements will now be shown directly on the LCD display.
5. A new zero may be obtained, at any open position of the calliper, by pressing the zero control.
6. A second measurement that then also needs to be added to the first one can be obtained by pressing the
ABS/0 switch after obtaining the first measurement (display will show ‘INC’), then move the callipers to
measure the second one. After noting this, press the ABS/0 switch again and the display will show the total
of both measurements.
A flashing display indicates that the battery is exhausted - replace as follows:
1. Switch off and then remove battery cover (9) by firmly sliding towards the right.
2. Remove exhausted battery and fit replacement with positive side uppermost (fig.1). Refit battery cover.
3. Dispose of old battery in a safe and approved manner. Do not burn.
If the display fails to alter when the slide is moved, remove the battery - wait at least 30 seconds and
then refit the battery.
fig.1
3. OPERATION
4. BATTERY FITTING
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
sales@sealey.co.uk
www.sealey.co.uk
Web
email
Environmental Protection.
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be
sorted, taken to a recycle centre and disposed of in a manner which is compatible with the environment.
When the product is no longer required, it must be disposed of in an environmentally protective way.
Do not incinerate battery as it may explode when exposed to fire.
Do not attempt to open battery.
Contact your local solid waste authority for recycling information.
AK9623EV Issue No: 1 - 24/09/08
Table des matières
Autres manuels Sealey Instrument de mesure
Sealey
Sealey Auto Service VS8196.V2 Manuel utilisateur
Sealey
Sealey TA050 Manuel utilisateur
Sealey
Sealey 6-24V AUTO PROBE PLUS Manuel utilisateur
Sealey
Sealey VS925.V2 Manuel utilisateur
Sealey
Sealey VS0566 Manuel utilisateur
Sealey
Sealey MM405 Manuel utilisateur
Sealey
Sealey DBG508 Manuel utilisateur
Sealey
Sealey VS0567 Manuel utilisateur
Sealey
Sealey TA101 Manuel utilisateur
Sealey
Sealey SA9302 Manuel utilisateur
Sealey
Sealey DBG507 Manuel utilisateur
Sealey
Sealey RS125.V2 Manuel utilisateur
Sealey
Sealey MM19.V3 Manuel utilisateur
Sealey
Sealey TA305 Manuel utilisateur
Sealey
Sealey DBG5010 Manuel utilisateur
Sealey
Sealey AK4013 Manuel utilisateur
Sealey
Sealey DBG5010.V2 Manuel utilisateur
Sealey
Sealey AUTO SERVICE VS0563 Manuel utilisateur
Sealey
Sealey TP91300.V2 Manuel utilisateur
Sealey
Sealey THC100 Manuel utilisateur
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
Keysight
Keysight M8290A Manuel utilisateur
ADTEK
ADTEK MW-5 Manuel utilisateur