Sealey SA9302 Manuel utilisateur

3.1 INSTALLATION FOR BOTH MODELS

3.1.1 AIR SUPPLY - MAXIMUM PRESSURE 12bar (175psi)

The supply must be clean and dry - use a suitable filter/water trap if necessary. The supply pressure at the gauge

inlet should ideally be 10bar (145psi).

Note: Maximum tyre inflation pressure cannot exceed the supply pressure.

1. SAFETY INSTRUCTIONS

3Disconnect the gauge from the air supply before changing accessories, servicing or performing any maintenance.

3Maintain the gauge in good condition (use an authorised service agent), and keep the gauge clean for best and safest

performance.

3Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate

the warranty.

3Locate gauge in a suitable work area, keep area clean and tidy and free from unrelated materials and ensure there is

adequate lighting.

3Keep children and unauthorised persons away from the work area.

7DO NOT direct gauge outlet at yourself or at other persons or animals.

7DO NOT carry by the hose, or yank the hose from the air supply.

7DO NOT use the gauge for a task which it is not designed to perform.

7DO NOT operate the gauge when you are tired or under the influence of alcohol, drugs or intoxicating medication.

7DO NOT operate gauge if parts are missing or the gauge is damaged, as this may cause failure and/or personal injury.

2. INTRODUCTION & SPECIFICATIONS

3. INSTALLATION

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS

PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL

INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS FOR FUTURE USE.

SA9302 & SA9312 - 1 - 091105

INSTRUCTIONS FOR:

PROFESSIONAL AIR LINE GAUGES

MODELS: SA9302 & SA9312

SA9302: Composite body and dial type gauge with rubber protector. Calibrated in bar/psi. Fitted with 500mm rubber hose

and single clip-on connector.

SA9312: Composite body and dial type gauge with rubber protector. Calibrated in bar/psi. Fitted with 500mm rubber hose

and a twin push-on connector.

SPECIFICATION. SA9302 SA9312

Range: 0-10bar (145psi). 0-10bar (145psi).

Air Supply Maximum: 12bar (175psi). 12bar (175psi).

Inlet: 1/4BSP Male. 1/4BSP Male.

Connector: Single clip. Twin push on.

Hose: 500mm rubber. 500mm rubber.

SA9312

SA9302

Clip-on Connector

Twin Push-on Connector

Operating Lever

Gauge

1/4BSP Male

5. MAINTENANCE & SERVICE

PERIODIC CHECKS AND MAINTENANCE

For long service and accuracy, the following actions should be carried out at the recommended intervals.

5.1 WEEKLY - CHECK OPERATION

The gauge should be checked weekly for correct operation. Look for smooth lever operation and fast, smooth gauge

movements. Check for leaks from tyre connector seals, and for chafing or wear of the flexible hoses. Any problems

should be immediately rectified.

5.2 QUARTERLY - CHECK CALIBRATION

We recommend the accuracy of the gauge be checked against a calibrated master gauge every 3 months, or at shorter

intervals depending on operators own quality procedures.

4. OPERATION

4.1 ATTACH ADAPTOR TO VALVE

Push and hold the connector onto the tyre valve using the most convenient side of the twin valve connector (SA9312).

For SA9302, squeeze the thumb clip on the connector, push the connector onto the tyre valve and release the clip.

The connector will now be locked in place.

4.2 TO INFLATE

Momentarily depress the operation lever fully, then release to display tyre pressure. When reading the pressure, hold the

gauge flat with respect to the eye to minimise error.

Fully depress operation lever for an appropriate period. Avoid over inflation, release lever frequently to check the pressure.

4.3 TO DEFLATE

Depress lever half-way (until air can be heard escaping) for an appropriate period. Fully depress lever momentarily then

release to display new pressure.

IMPORTANT - ALWAYS FULLY DEPRESS LEVER MOMENTARILY BEFORE READING TYRE PRESSURE.

SA9302 SA9312

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.

IMPORTANT: No liability is accepted for incorrect use of these products.

WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.

INFORMATION: For a copy of our catalogue and latest promotions call us on 01284 757525 and leave your full name, address and postcode.

sales@sealey.co.uk

www.sealey.co.uk

Web

01284 757500

01284 703534

Sole UK Distributor

Sealey Group,

Bury St. Edmunds, Suffolk.

SA9302 & SA9312 - 1 - 091105

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Sealey Instrument de mesure

Sealey

Sealey TP956.V2 Manuel utilisateur

Sealey

Sealey TA203.V2 Manuel utilisateur

Sealey

Sealey TP101 Manuel utilisateur

Sealey

Sealey GA48.V2 Manuel utilisateur

Sealey

Sealey DBG506D Manuel utilisateur

Sealey

Sealey VS0563 Manuel utilisateur

Sealey

Sealey DBG509 Manuel utilisateur

Sealey

Sealey TA305 Manuel utilisateur

Sealey

Sealey VS0560.V2 Manuel utilisateur

Sealey

Sealey MM19.V3 Manuel utilisateur

Sealey

Sealey TA302 Manuel utilisateur

Sealey

Sealey DBG507 Manuel utilisateur

Sealey

Sealey AK9991 Manuel utilisateur

Sealey

Sealey TP91300.V2 Manuel utilisateur

Sealey

Sealey AK9623EV Manuel utilisateur

Sealey

Sealey AK9638D Manuel utilisateur

Sealey

Sealey TA060 Manuel utilisateur

Sealey

Sealey AK9621EV Manuel utilisateur

Sealey

Sealey STW701 Manuel utilisateur

Sealey

Sealey TA304 Manuel utilisateur

Sealey

Sealey GA450 Manuel utilisateur

Sealey

Sealey AK9638D Manuel utilisateur

Sealey

Sealey BT91/5.V3 Manuel utilisateur

Sealey

Sealey AK4013 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur