SDC Z7835 Manuel utilisateur
Any suggestions or comments to this instruction or
product are welcome. Please contact us through
our website or email engineer@sdcsecurity.com
A. Door Preparation:
1. Measure desired height from finished floor, mark a horizontal line on door and door edge.
2. Align template on edge of door with applicable horizontal at height line. Check the chart for drilling trim
holes on template and mark only holes for lock function being installed.
3. Mortise door edge according to measurements on
installation template and drill proper holes for trim.
4. Recess for face plate, the dimension is:
L 8-1/32" x W 1-5/16" x D 7/32".
Height
line
of lever
or knob
C
L
7/32"
Z7835
24VDC MORTISE LOCK
of cylinder
of lockcase
of lever or knob
Vertical centerline
Installation
template
C
L
C
L
C
L
of door edge
OPTIONAL
DOOR CORE DRILLING GUIDE
#7000-DG
P:\INST INSTRUCTIONS\ELECTRIFIED LOCKSETS\INST-Z7835-C REF G 02-21 Page 1
SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011
INSTALLATION INSTRUCTIONS
C
L
P:\INST INSTRUCTIONS\ELECTRIFIED LOCKSETS\INST-Z7835-C REF G 02-21 Page 2
B. Strike Installation:
1. Align strike template on jamb. Be sure to keep 3/8" distance between lock centerline and strike
centerline. Recess 5/32" for flush fit of strike and dust box.
2. Mortise jamb according to measurement of strike template. Then fit strike and dust box into frame
and secure into place with supplied screws.
4-7/8"
3-17/32"
C
L
Strike
Lock C
L
3/8"
3/8"
1" Holes
1-1/8" Deep
C
L
Jamb
Pull out and
turn
1. Change latchbolt handing
If the hand of the latchbolt doesn’t match the door hand, remove the fixing screw and pull the latchbolt out from
lock case. Turn the latchbolt 180 ° to change the handling. Position latchbolt back, into case and fasten it.
Instructions for changing latchbolt handing:
C. Install Lockcase
Remove
screw
SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011
1. Insert spindles as shown
E. Install Lever trim
1. Place the reversible spring cage onto the ferrules with arrow pointing in direction of lever rotation.
2. Install outside trim with mounting posts through door and position lever onto the spindle.
3. Install inside spring cage onto the spindle with the arrow pointing in the direction of inside lever rotation.
4. Install inside mounting plate onto spindle. Tighten with provided screw.
5. Cap inside rose over mounting plate.
D. Install Spindles
Reversible spring
cage
Ferrule
Mounting
post Into Mounting
post
P:\INST INSTRUCTIONS\ELECTRIFIED LOCKSETS\INST-Z7835-C REF G 02-21 Page 3
3. Connect wires as shown on the lock cover diagram.
4. Insert lockcase into mortise cut-out and fasten screws to door.
C. Install Lockcase (Continued)
SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011
P:\INST INSTRUCTIONS\ELECTRIFIED LOCKSETS\INST-Z7835-C REF G 02-21 Page 4
1. Screw cylinder into threaded hole of lock case.
2. Tighten the setting screw against cylinder(s) by turning clockwise as shown.
3. Install face plate onto lock case front and fasten with supplied screws.
F. Install Cylinder and Armor Face Plate
USE THIS CAM.
E. Install Lever trim (continued)
6. Screw inside lever into position and tighten lever collar with supplied spanner wrench.
Spanner wrench
Spanner wrench
SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011
INSTALLATION WIRE DIAGRAM
Model Z7835 Series 24VDC ONLY
STANDARD WIRING
(NO OPTIONS)
24VDC 4 PIN
CONECTOR
WIRING WITH OPTIONS
GREEN COM
DPS BLACK N/C
WHITE N/O
ORANGE COM
REX BROWN N/C
YELLOW N/O
RED/YELLOW COM
LLS RED/BLACK SECURE
RED/GREEN UNSECURE
MOV*
MOV*
*Install MOV across each coil to protect ACS electronics.
Install as close as possible to the lock
*Install MOV across each coil to protect ACS electronics.
Install as close as possible to the lock
P:\INST INSTRUCTIONS\ELECTRIFIED LOCKSETS\INST-Z7835-C REF G 02-21 Page 5
SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011
OUTSIDE SOLENOID
OUTSIDE SOLENOID
INSIDE SOLENOID
INSIDE SOLENOID
GREEN
BLACK
WHITE
RED (+)
(+)
(-)
(-)
OUTSIDE SOLENOID
OUTSIDE SOLENOID
INSIDE SOLENOID
INSIDE SOLENOID
(+)
(+)
(-)
(-)
VIOLET
GREY
RED
PINK
Fail-Secure
Fail-Safe
Fail-Secure
Fail-Safe
Table des matières
Autres manuels SDC Serrure de porte
SDC
SDC E70PS Series Manuel du propriétaire
SDC
SDC 30-4 Manuel utilisateur
SDC
SDC S6300 Series Manuel utilisateur
SDC
SDC EntryCheck E75 Series Manuel utilisateur
SDC
SDC E75 Series Mode d'emploi
SDC
SDC FS23M Series Manuel utilisateur
SDC
SDC E72 EntryCheck Guide de dépannage
SDC
SDC HiTower R7500 Manuel utilisateur
SDC
SDC Spacesaver 1091 ADMR Manuel utilisateur
SDC
SDC 352 Narrow Line EMLock Manuel utilisateur
SDC
SDC Z7700 Series Manuel utilisateur
SDC
SDC E72 EntryCheck Manuel utilisateur
SDC
SDC 1511S Manuel utilisateur
SDC
SDC 1190A Series Manuel utilisateur
SDC
SDC TEMPLATE 180 SERIES Manuel utilisateur
SDC
SDC Z7200R Manuel utilisateur
SDC
SDC E72K-A CIVIC SERIES Manuel d'installation
SDC
SDC Z7200 Manuel utilisateur
SDC
SDC 45 Series Manuel utilisateur
SDC
SDC SK-82 Manuel utilisateur
