SDC Z7200R Manuel utilisateur
801 Avenida Acaso, Camarillo, Ca. 93012 • (805) 494-0622 • Fax: (805) 494-8861
Any suggestions or comments to this instruction or
product are welcome. Please contact us through
P:\INSTALLATION INST\ELECTRIFIED LOCKSET\Z7200\INST-Z7200R.vsd REV - 03-17 Page 1
INSTALLATION INSTRUCTIONS
CYLINDRICAL LOCK Z7200R
FOR USE ON DOORS 1-3/8” ~ 2" (35mm ~ 51mm) THICK
1. MARK DOOR 2. DRILL HOLES
a. Mark centerline on door face and door edge
(usually 38" from finished floor)
b. Select backset 2-3/8” or 2-3/4” and mark hole
center on door face
NOTE: BACKSET ON DOOR FACE MUST BE
THE SAME AS BACKSET OF YOUR
LOCK.
c. Mark two holes for screw post.
2-1/8” (54mm)
Hole for lockset
5/16” (8mm) hole for
screw post
a
b
c
1" or 31/32"
(24.6mm or 25.4mm)
hole for latch
Fold template for High or
Low Bevel positioning
(reference template)
OPTIONAL:
DOOR CORE DRILLING GUIDE #7000-DG &
CORING DRILL BIT #7000-DB
TOOLS REQUIRED FOR NEW INSTALLATION:
1 philips head screwdriver 1 2-1/8” (54MM) hole saw
1 1" (25.4mm) drill bit 1 5/16” (8mm) drill bit
1 chisel 1 file
LATCH
LOCK BODY
ASSEMBLY OUTSIDE
MOUNTING
PLATE
OUTSIDE
ROSE
OUTSIDE
LEVER
INSIDE
LEVER
LEVER
CATCH
TOOL
INSIDE
ROSE w/LINER
INSIDE MOUNTING
PLATE
P:\INSTALLATION INST\ELECTRIFIED LOCKSET\Z7200\INST-Z7200R.vsd REV - 03-17 Page 2
5. REMOVE INSIDE TRIM
3. INSTALL LATCH 4. INSTALL STRIKE
a. Insert latch in hole and keep it parallel to door face.
Mark outline and remove latch
b. Chisel 1/8” (3mm) deep or until faceplate is flush with
door edge.
c. Insert latch and tighten screws.
NOTE: LATCH BOLT BEVEL MUST FACE TOWARDS
CLOSING DIRECTION.
a. Close door to mark horizontal line of strike.
b. Measure one half of door thickness from
door stop to mark vertical center line of strike.
Drill 1" (25.4mm) hole, 1/2” (12.7mm) deep at
intersection of horizontal and vertical center lines.
c. Cut out jamb 3/32” (2.4mm) deep or until strike
is flush with jamb. Tighten screws securely.
c
a
b
a
b
CENTER
LINE
1" (25.4mm) hole
1/2” (12.7mm) deep
c
Use lever catch tool to depress lever
catch, visible under hole of inside lever
shank and slide off inside lever, rose
liner and mounting plate.
INSIDE LEVER
INSIDE ROSE
LINER
LEVER CATCH
TOOL
OUTSIDE LEVER
ASSEMBLY
INSIDE MOUNTING
PLATE
ROSE
P:\INSTALLATION INST\ELECTRIFIED LOCKSET\Z7200\INST-Z7200R.vsd REV - 03-17 Page 3
6. ADJUST DOOR THICKNESS 7. INSTALL OUTSIDE LEVER ASSEMBLY
Install outside lever assembly on the door. Make sure tail
of latch is engaging with retractor correctly as illustrated.
Refer to wire diagram on last page for wiring.
8. INSTALL INSIDE MOUNTING
PLATE AND ROSE 9. INSTALL LEVER
a. Install inside mounting plate to lock body.
a. Depress lever catch with tool provided.
Push inside lever on completely until
catch engages in lever.
Confirm lever is secured.
LOCK BODY
ASSEMBLY
LATCH
INSIDE
LEVER
INSIDE
MOUNTING
PLATE
INSIDE
ROSE
1-3/4" thick
Door thickness : 2" thick
1-3/8" thick
b. Press inside rose
onto mounting plate
and tighten screws securely.
MOUNTING
SCREWS
INSIDE
ROSE
ROSE
LINER
P:\INSTALLATION INST\ELECTRIFIED LOCKSET\Z7200\INST-Z7200R.vsd REV - 03-17 Page 4
REQUEST-TO-EXIT MAGNETIC SENSOR, 200mA @ 30VAC RESISTIVE
COM = GREY
N/C = YELLOW
N/O = ORANGE
REX
WIRE DIAGRAM
Flat (No Bevel)
5/32" (4mm)
1-3/4” Door
1-5/8"
(41mm)
1/8" (3mm)
Holes
2-3/8" (60mm) BACKSET
MARK CENTER OF
2-1/8” (54mm)
HOLE ON DOOR FACE
2-3/4” (70mm) BACKSET (FOR METAL
DOORS ONLY)
DOOR EDGE
2X 5/16" (8mm)
hole
High Bevel
Low Bevel
1" (25mm)
Hole
2-3/4”
(70mm)
LAYOUT
2-15/32" (62.7mm) (FOR METAL
DOORS ONLY)
DO NOT USE AS A PHYSICAL TEMPLATE. THIS LAYOUT
IS INTENDED AS A DIMENSIONAL REFERENCE ONLY.
USE THE TEMPLATE PACKAGED WITH THE LOCK
Use of the PR-7200 limits the power consumption, reduces operating temperature, and
suppresses inductive kickback.
RED
BLK
WHT
BLU
RED(+)
WHT(-)
LOCKSET PR-7200
POWER REGULATOR
BLU
WHT
TO PWR
SUPPLY
RED (+)
BLK (-)
12vdc @ INRUSH: .6A
HOLDING: .25A
RED(+)
WHT(-)
RED
BLK
WHT
BLU
LOCKSET PR-7200
POWER REGULATOR
BLU
WHT TO PWR
SUPPLY
RED (+)
BLK (-)
24vdc @ INRUSH: .3A
HOLDING: .15A
Table des matières
Autres manuels SDC Serrure de porte
SDC
SDC Z7835 Series Manuel utilisateur
SDC
SDC FS23M Series Manuel utilisateur
SDC
SDC ZY7500 Series Manuel utilisateur
SDC
SDC 352 Narrow Line EMLock Manuel utilisateur
SDC
SDC PD2090A Manuel utilisateur
SDC
SDC 30-4-12 Manuel utilisateur
SDC
SDC Spacesaver 1091 ADMR Manuel utilisateur
SDC
SDC 1511S Manuel utilisateur
SDC
SDC 30-4 Manuel utilisateur
SDC
SDC Z7500 Series Manuel utilisateur
SDC
SDC Z7200 Manuel utilisateur
SDC
SDC 1291 ADMR Spacesaver Manuel utilisateur
SDC
SDC 45 Series Manuel utilisateur
SDC
SDC EntryCheck E75 Series Manuel utilisateur
SDC
SDC 1190A Series Manuel utilisateur
SDC
SDC E75 Series Mode d'emploi
SDC
SDC S6100 Series Manuel utilisateur
SDC
SDC PRO Series Manuel utilisateur
SDC
SDC S6200 Series Manuel utilisateur
SDC
SDC Z7500 Series Manuel utilisateur
