SDC Z7700 Series Manuel utilisateur
P:\INSTALLATION INST\Electrified Lockset\INST-Z7700 REV 09-19 P ge 1
Any suggestions or comments to this instruction or
product re welcome. Ple se cont ct us through
our website or em il engineer@sdcsecurity.com
A. Door Preparation:
1. Me sure desired height from finished floor, m rk horizont l line on door nd door edge.
2. Align templ te on edge of door with pplic ble horizont l t height line. Check the ch rt for drilling trim
holes on templ te nd m rk only holes for lock function being inst lled.
3. Mortise door edge ccording to me surements on
inst ll tion templ te nd drill proper holes for trim.
4. Recess for f ce pl te, the dimension is:
L 8-1/32" x W 1-5/16" x D 7/32".
5. Route wiring through door s required. Reference
wiring section on P ge 4
Height line
of lever
or knob
C
L
7/32"
INSTALLATION INSTRUCTIONS
Z7700 SERIES MOTORIZED RETRACTION x ELECTRIC SOLENOID
MORTISE LOCK SET
of cylinder
of lockc se
of lever
or knob
Vertic l centerline
C
Inst ll tion
templ te
C
L
C
L
C
L
Lof
door edge
801 Avenida Acaso, Camarillo, Ca. 93012 • (805) 494-0622 •
www.sdcsec rity.com • E-mail: service@sdcsec rity.com
NOTCH OPENING FOR MOTOR
ON WOOD DOORS ONLY
*
. Strike Installation: 1. Align strike templ te on j mb.
Be sure to keep 3/8" dist nce
between lock centerline nd
strike centerline. Recess
5/32" for flush fit of strike nd
dust box.
2. Mortise j mb ccording to
me surement of strike templ te.
Then fit strike nd dust box into
fr me nd secure into pl ce with
supplied screws.
4-7/8"
3-17/32"
3/8"
3/8"
1" Holes
1-1/8" Deep
C
L
J mb
Lock C
L
C
L
Strike
3/8"
2X 12-24 WMS
5-5/8"
1-1/4”
(1-3/4” DEEP)
3/8”
2-1/4”
1-1/2”
(1-3/4” DEEP)
1" hole
4-3/4“ DEEP
*
WOOD
DOOR
P:\INSTALLATION INST\Electrified Lockset\INST-Z7700 REV 09-19 P ge 2
2. Connect wires s shown in the lock wiring section on p ge 4.
3. Insert lockc se into mortise cut-out nd f sten screws to door.
Pull out nd turn
1. Ch nge l tchbolt h nding:
If the h nd of the l tchbolt doesn’t
m tch the door h nd, remove the fixing
screw nd pull the l tchbolt out from
lock c se. Turn the l tchbolt 180° to
ch nge the h ndling. Position l tchbolt
b ck, into c se nd re-f sten it.
Instructions for changing lock hand:
C. Install Lockcase
Remove screw
1. Insert spindles s shown
D. Install Spindles
E. Install Lever trim
1. Pl ce the reversible spring c ge onto the ferrules with rrow pointing in
direction of lever rot tion.
2. Inst ll outside trim with mounting posts through door nd position lever
onto the spindle.
3. Inst ll inside spring c ge onto the spindle with the rrow pointing in the
direction of inside lever rot tion.
4. Inst ll inside mounting pl te onto spindle. Tighten with provided screw.
5. C p inside rose over mounting pl te.
Reversible spring c ge
Ferrule
Mounting post
Into Mounting post
P:\INSTALLATION INST\Electrified Lockset\INST-Z7700 REV 09-19 P ge 3
1. Screw cylinder into thre ded hole of lock c se.
2. Tighten the setting screw g inst cylinder(s) by turning clockwise s shown.
3. Inst ll f ce pl te onto lock c se front nd f sten with supplied screws.
F. Install Cylinder and Armor Face Plate
USE THIS CAM.
E. Install Lever trim (continued)
6. Screw inside lever into position nd tighten lever coll r with supplied sp nner wrench.
sp nner wrench.
Sp nner wrench
G. Lock Wiring
Use
f ctory
provided
pigt ils
Power &
Controls
Optional
REX nd/or
L tch St tus
Outputs
FIELD WIRING:
6 COND MINIMUM
18-22AWG
JACKETED CABLE
100' MAX from Power Supply to Lock
Solenoid
Activation
Switch
(Dry, N/O)
PWR LEVER LATCH
+CNO CNO
Extern l Control Bo rd
Motor
Activation
Switch
(Dry, N/O)
Motor Activation Switch: Closing the switch for
minimum of 2 seconds retr cts the l tch.
Rele se switch to rele se l tch.
Solenoid Activation Switch: Closing the switch
will provide power to the solenoid.
If the solenoid is f il-s fe, ctiv ting the switch
will lock the lever.
If the solenoid is f il-secure, ctiv ting the switch
will unlock the lever.
24VDC
Regul ted &
Filtered Power
Supply
(1.5A min)
SDC P/N 631RF
is recommended.
24VDC (Continuous)
GRY
VIO
BRN
YEL
REX N/O
REX/L tch St tus COM
L tch St tus N/O
L tch St tus N/C
Power
Transfer
Device
6 Cond Min
10 Cond w/ Options
Z7700
Series
1A @ 30vdc
P:\INSTALLATION INST\Electrified Lockset\INST-Z7700 REV 09-19 P ge 4
P:\INSTALLATION INST\Electrified Lockset\INST-Z7700 REV 09-19 P ge 5
OPTIONAL
DOOR CORE DRILLING GUIDE
#7000-DG
M ke sure the lock h nd m tches the door h nd, use the following di gr m to determine the h nd of door.
LH
Left H nd
LHRB
Left H nd
Reverse Bevel
INSIDE OF DOOR
OUTSIDE OF DOOR
RH
Right H nd
RHRB
Right H nd
Reverse Bevel
INSIDE OF DOOR
OUTSIDE OF DOOR
Autres manuels SDC Serrure de porte
SDC
SDC E70PS Series Manuel du propriétaire
SDC
SDC E75 Series Manuel utilisateur
SDC
SDC HiTower R7500 Manuel utilisateur
SDC
SDC E75 Series Manuel utilisateur
SDC
SDC EntryCheck E75 Series Manuel utilisateur
SDC
SDC Excel E1200 Series Manuel utilisateur
SDC
SDC E72 EntryCheck Guide de dépannage
SDC
SDC S6800 Series Guide de démarrage rapide
SDC
SDC FS23M Series Manuel utilisateur
SDC
SDC S6300 Series Manuel utilisateur
SDC
SDC PD2090A Manuel utilisateur
SDC
SDC Z7800 Series Manuel utilisateur
SDC
SDC 1511S Manuel utilisateur
SDC
SDC PBD2090A Manuel utilisateur
SDC
SDC S6100 Series Manuel utilisateur
SDC
SDC Spacesaver 1091 ADMR Manuel utilisateur
SDC
SDC 30-4-12 Manuel utilisateur
SDC
SDC ZY7500 Series Manuel utilisateur
SDC
SDC 1190A Series Manuel utilisateur
SDC
SDC 1291 ADMR Spacesaver Manuel utilisateur
