Sartorius ISBBS Manuel utilisateur

Operating Instructions

Sartorius ISBBS, ISDCS

Weighing Platform

98648-019-05

2ISBBS, ISDCS Operating Instructions

Table of Contents

Intended Use........................................................................3

Warnings and Safety Precautions ....................................4

Getting Started...................................................................5

Installation Instructions.....................................................6

Leveling the Weighing Platform ...................................6

Ground Conductor...........................................................6

Data Interface.....................................................................7

Pin Assignment ................................................................7

Menu Access Switch...........................................................8

Specifications ......................................................................9

ISBBS Weighing Data.......................................................10

ISDCS Weighing Data.......................................................11

Error Messages..................................................................12

Care and Maintenance.....................................................13

Cleaning Stainless Steel Surfaces...............................14

Disposal ..............................................................................15

Potentially Explosive Atmosphere ..................................16

Dimensions (Scale Drawings)...........................................18

ISBBS, ISDCS Operating Instructions 3

Legal Terms and Conditions

This documentation may not be reproduced or distributed either in whole or in

part without the explicit written permission of Sartorius.

This documentation is intended only for use by the buyer.

Transfer to third parties, whether free or in exchange for payment, is not

permitted.

The software is the property of Sartorius. The software may not be copied or

modiﬁed; it may not be decompiled or modiﬁed through assimilation.

The buyer may only use the software for his own purposes and may not make

the software available to third parties for use either for free or in exchange for

payment. If you encounter problems with the included software, please contact

the software distributor. Sartorius reserves the right to deliver updated software

for this product.

No liability is accepted for software installed before the purchase of this product.

The buyer is liable for any misuse of the product.

Intended Use

As precise and robust weighing platforms, the ISBBS and ISDCS provide

reliable weighing results. The models are based on monolithic

technology (the principle of electromagnetic force compensation).

These industrial weighing platforms offer the following special features:

– Robust and durable Sartorius quality

– IP65 protection from dust and jets of water

– High-quality workmanship and materials

– Preload values can be deﬁned (for equipment installed on the scale)

4ISBBS, ISDCS Operating Instructions

Safety Precautions

Warnings and Safety Precautions

3 Read these operating instructions thoroughly before using the weighing

platform, in order to prevent damage to the equipment.

3 The weighing platforms comply with the European Council Directives as well as

international regulations and standards for electrical equipment, electromagnetic

compatibility, and the stipulated safety requirements.

3 Do not expose the equipment to aggressive chemical vapors or to unnecessarily

extreme temperatures, moisture, shocks, or vibration.

2 Avoid generating static electricity and connect equipotential bonding terminals.

3 All models meet the criteria for protection class IP65.

Any installation work that does not conform to the instructions in this manual

results in forfeiture of all claims under the manufacturer’s warranty.

3 If there is any indication that safe operation of the equipment is no longer

guaranteed, disconnect the platform from the power and ensure that it is not

used further.

3 Always ensure that the weighing platform is disconnected from AC power before

performing any maintenance, cleaning, or repair work.

3 Note the pin assignments when using cables provided by other manufacturers.

Check the connections of the cable against the corresponding cabling diagram

before connecting to the Sartorius equipment and disconnect any wires that are

assigned differently. The operator shall be solely responsible when using cables

not supplied by Sartorius.

3 The weight value can be affected by extreme electromagnetic inﬂuences.

Once the disturbance has ceased, the instrument can be used again in

accordance with its intended purpose.

ISBBS, ISDCS Operating Instructions 5

Getting Started

Warning:

3 Unpacked devices can lose their precision if subject to extreme vibrations.

Excessive vibrations may compromise the safety of the equipment. Do not

expose the equipment to unnecessarily extreme temperatures, moisture,

shocks, or vibrations.

Permitted storage temperature: -10°C to +40°C

Unpacking the Equipment

Remove the device from the packaging. Check for any visible damage. Save the

original packaging for any future transport. Unplug all connected cables before

packing the equipment.

Acclimatizing the Device

3 The device should only be opened by trained and qualiﬁed personnel.

Before opening the valve unit: Turn the main switch to “OFF." Take all steps

necessary to secure the equipment against unauthorized power-up.

Disconnect the device from the power supply if possible.

Once work is completed: Securely lock the valve unit.

Scope of Supply:

– Weighing platform

– Operating instructions

– Special accessories as listed on the bill of delivery, if ordered

6ISBBS, ISDCS Operating Instructions

Installation Instructions

t Set up a suitable installation location for the weighing platform.

The place of installation should be dry, level, and ﬂat. The operating temperature

ranges from -10°C to +40°C.

The weighing platform must not be subjected to unnecessarily extreme

temperatures, moisture, shocks, or vibrations that could result in damage.

Leveling the Weighing Platform

Purpose: – To compensate for uneven areas at the place of installation

– To ensure that the equipment is placed in a perfectly horizontal

position for consistently reproducible weighing results

Always level the weighing platform again any time after it has been moved to

a different location.

t Level the weighing platform using the four leveling feet. Turn the feet until

the air bubble is centered in the level indicator.

t Check to ensure that all leveling feet rest securely on the work surface.

y Each of the leveling feet must support an equal load.

y Adjusting the leveling feet:

To raise the weighing platform, extend the leveling feet (turn counterclockwise).

To lower the weighing platform, retract the leveling feet (turn clockwise).

Ground Conductor

The ground conductor is located underneath the weighing pan on the clamp

box or on the lower base of the weighing platform. It is marked as a ground

connection with the symbol shown here.

Grounding is implemented using a threaded bolt or screw terminal, or as a hole.

If a ground hole is the method of grounding, a stainless steel screw and nut

must be used. A lock washer should be placed underneath in order to prevent

the screw from loosening. The grounding cable must have a minimum cross-

section of 4 mm2 and must be ﬁtted with a suitable ring terminal. Connect

all equipment, including peripheral devices, to the equipotential bonding

conductor.

°C

ISBBS, ISDCS Operating Instructions 7

Data Interface

The weighing platform has a standard COM1 interface, RS-485 socket (IP65).

The standard COM1 interface can be converted to RS-232 through the

Sartorius Service Center.

Pin Assignment

COM 1 round plug connector with screw connection.

Front view:

RS-485 data interface RS-232 data interface

A RxD–TxD–N Not used

B Not used RxD

C Not used TxD

D Not used CTS

E GND GND

F Menu access switch

for adjustment

Menu access switch

for adjustment

G 12-30 VDC 2W supply 12-30 VDC 2W supply

H Not used DTR

J GND GND

K GND GND

L RxD–TxD–P Not used

M 12-30 VDC 2W supply 12-30 VDC 2W supply

h Female Interface Connector (Recommended):

Type C091D, 12-pin, Amphenol (IP65) cable type as per AWG 24

Observe power supply instructions.

Operation as an RS485-interface:

Switch 4 must be open in order to switch to RS-485 operation (factory setting).

Where applicable, deactivate bias resistors for RS-485 operation. Open switches

for this purpose (factory setting).There must only be one instance of bias

resistors per transmission path (network orpoint-to-point connection). Otherwise

there is a risk of transmission errors. Where applicable, refer to the speciﬁcations

or circuit documentation for the remote station or network nodes in question.

Bias resistors must always be activated or deactivated in pairs. The terminating

resistor (transmitting side, switch 1 must be activated if the device is located at

either end of an RS-485 bus system, or where it is connected to another device

in a point-to-point link. There must also be a terminating resistor of 120 Ω in

place at the remote station. Where applicable, activate terminating resistor 120

Ω for RS-485operation:

Terminating resistor, receiving side 120 ΩSwitch 1 on

BIAS resistor, receiving side (RxD+, pull-up) 680 ΩSwitch 2 on

BIAS resistor, receiving side (RxD–, pull-down) 680 ΩSwitchr 3 on

No function Switch 4

Data Interface

8ISBBS, ISDCS Operating Instructions

Menu Access Switch

ISBBS

Switch on the right = for use in legal metrology

Switch on the left = external calibration/adjustment accessible

ISDCS

Switch on the right = for use in legal metrology

Switch on the left = external calibration/adjustment accessible

ISBBS, ISDCS Operating Instructions 9

Speciﬁcations

Specifications

General Specifications

The CE conformity is only guaranteed when using Sartorius accessories.

Digital protective interface as per EN 45501

Data interface RS-485

Housing: material

Protection class as per EN 60529

stainless steel

IP65

Temperature range –10°C to +40°C

Humidity max. relative humidity is 80% for temperatures up to 31°C

DC supply optional 15.524 V DC (±10%), max. 12 W via interface

Interference emission as per EN 61326+A1, Class B (IEC 61326+A1)

Interference immunity as per EN 61326+A1, industrial areas (IEC 61326+A1)

Electrical safety as per EN 61010-1 (IEC 61010-1), EN 60950 (IEC 60950)

10 ISBBS, ISDCS Operating Instructions

ISBBS Weighing Data

Non-verifiable Models

Weighing capacity (kg) 3.1 6.1

Readability (g) 0.01 0.01

Resolution code -H -H

Calibration weight value

(in grams)

2000 5000

Accuracy class E2 E2

Preload (kg) 3 0

Reproducibility (g) 0.01 0.01

Linearity (g) 0.02 0.02

Ambient temperature -10°C to +40°C

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Sartorius Échelle

Sartorius

Sartorius PMA.Evolution Manuel utilisateur

Sartorius

Sartorius BL310 Manuel utilisateur

Sartorius

Sartorius 2406 Guide de l'utilisateur

Sartorius

Sartorius YDK 01 Manuel utilisateur

Sartorius

Sartorius PMA.HD Manuel utilisateur

Sartorius

Sartorius Secura Manuel utilisateur

Sartorius

Sartorius Genius Series Manuel utilisateur

Sartorius

Sartorius XQ 6100 Manuel utilisateur

Sartorius

Sartorius Element Series Manuel utilisateur

Sartorius

Sartorius EC1XS Manuel utilisateur

Sartorius

Sartorius talent Manuel utilisateur

Sartorius

Sartorius CW3P Manuel utilisateur

Sartorius

Sartorius FB Manuel utilisateur

Sartorius

Sartorius Master series Manuel utilisateur

Sartorius

Sartorius PMA.Evolution EVO1Y1 Manuel utilisateur

Sartorius

Sartorius Signum 1 Manuel utilisateur

Sartorius

Sartorius FC Manuel utilisateur

Sartorius

Sartorius PMA 7501-000G Manuel utilisateur

Sartorius

Sartorius Secura Manuel utilisateur

Sartorius

Sartorius EVO1Y Manuel utilisateur

Sartorius

Sartorius Combics CAW1P Manuel utilisateur

Sartorius

Sartorius YDS01SQP Manuel utilisateur

Sartorius

Sartorius Factory Series FC06BBE-S Manuel utilisateur

Sartorius

Sartorius IW2P1x-6ED-L Manuel utilisateur

Manuels Échelle populaires d'autres marques

AWS

AWS ZEO-50 Manuel utilisateur

Gima

Gima Glass Body Fat Analyzer Manuel de la liste des pièces

Seca

Seca 374 Manuel utilisateur

TEC

TEC TEC SL59 SERIES Manuel utilisateur

Axis

Axis B/E Series Manuel utilisateur

Alecto

Alecto ACW-40 Manuel utilisateur

Rice Lake

Rice Lake MSI-4260 IS Manuel utilisateur

IKA

IKA RCT basic safety control Manuel utilisateur

ADE

ADE M20011 Manuel utilisateur

Duronic

Duronic KS3000 Manuel utilisateur

Digi

Digi SM-720 Manuel utilisateur

Cardinal

Cardinal CS Series Manuel utilisateur

Korona

Korona Kastella Manuel utilisateur

A&D

A&D FC-50Ki Manuel utilisateur

BDA

BDA CAMARGUE Manuel utilisateur

Tanita

Tanita HD-357 Manuel utilisateur

Leifheit

Leifheit 03173 Manuel utilisateur

Lumme

Lumme LU-1340 Manuel utilisateur