Sartorius U 3600 Manuel utilisateur

Sartorius Universal.

U 3600, U 3600 P.

U 3600 S-*F2

Installation and operating instructions

1 Pan

2 Power connection, fuse, voltage selector

3 Manufacturer’s label

4 Unlocking switch

5 Tare button

6 CAL button

7 ON/OFF button

8 Weight display

Contents.

Page

Complete Consignment 5

Startup 6

Operation 7

Calibration 9

Balance Operating Program 10

Technical data 13

Sartorius Universal

U 3600, U 3600 P.

Before reading these instructions, fold out the first page with the

exploded view drawing.

With this Sartorius toploader you have acquired a sophisticated,

top-of-the line electronic balance, which will help lighten your

daily workload.

Please read these Installation and operating instructions care-

fully before operating your new toploader.

Installation Instructions.

Choose a suitable place to set up your balance. It should not be

exposed to the following:

- heat radiation

-aggressive/corrosive substances

-vibrations

-drafts.

Your Sartorius Balance will provide accurate readouts even

when it is exposed to unfavorable conditions. You can adapt it

to your requirements simply by changing the menu code set-

tings of the balance operating program. For this purpose,

please read pages 10 through 12.

After you plug your balance into a wall outlet, allow for at least

30 minutes warmup.

Important Note

Unplug the AC adapter before you connect or disconnect pe-

ripherals.

Accessories

Calibration weight 7072 08

Data output

Integratable keyboard

»Data Input« YDI 01 U-**&

with & = C for parts counting

= F for formulation and weight unit conversion

= A foe animal weighing

Printer »Data Print« 7279

Carrying case YDB 01 U

Theft prevention lock 6087

Complete Consignment.

Please complete the guarantee card, indicating the installation

date, and return to your Sartorius dealer.

Complete consignment

A complete consignment consists of the illustrated components.

Startup.

Install the pan on your toploader.

The operating voltage was set to 220 V at the factory.

Adaptation to your local line voltage:

set the voltage selector (2) to your line voltage.

Write the new setting on the manufacturer's label (3). Whenever

you change the voltage to 100/120 you must switch fuses: ex-

change the T 160 mA fuse (2) for the T 315 mA fuse that is in-

cluded in the toploader.

You will find this fuse plugged in the rear panel together with the

voltage selector:

100/120 V-T 315mA

220/240 V-T160mA

At the point of use, plug the line cord into a properly installed

line outlet.

lf you have to use a line outlet that lacks the ground wire,

make sure you ground the toploader itself.

Operation.

The weight display shows the following special

Status messages for your Information:

BUSY

The processor is still busy processing a function and will not ac-

cept any other commands to perform functions at this time.

STANDBY

The balance has been turned off with the ON/OFF key (5) and

is now in the STANDBY mode and ready to operate without

warmup.

POWER OFF

The balance was disconnected from line power (reconnection to

line power, power failure).

CAL

The calibration function has been called.

In addition to grams, this balance gives you a variety of

other international weight unit options to work with.

Select the weight unit you need from the table of the menu op-

tions for the balance operating program, and set the appropriate

code(s) as described in the section "Balance Operating Pro-

gram."

Press the ON/OFF key (7) to switch the balance on or off. You

can also turn on the balance with the tare control (5).

After the adapter has been plugged into a wall outlet, the weight

display will go out when ever you turn off the balance. AII other

electronic circuits will remain energized (STANDBY state).This

means the balance is immediately ready to operate without re-

quiring warmup the next time you switch it on.

After the power is turned on, a test of all essential electronic

functions is run automatically.

The self-test ends with the readout 0.00 g/0.0 g (if the program

code setting 5 1 1 is used).

Now place your sample on the pan (1) to determine the weight.

Read off the weight in the display (8) as soon as the weight unit

(in this case ''g") appears as the stability symbol.

lf you wish to use a Container or if the weight display does not

indicate 0.00 g/0.0 g (or the equivalent with the weight unit of

your choice), press the tare control to zero the display.

Calibration.

- is only possible with an accurate calibration weight.

Please refer to "Accessories."

Clear the pan and depress the QAL button for at least three

seconds until the calibration weight appears in the display.

Place the calibration weight in the center of the pan.

Now the weight unit symbol appears, and a beeper Signals the

end of the calibration procedure.

You can disable the calibration function – see "Balance operat-

ing program". (The function is enabled whenever the balance

operating program is in the "C" mode).

Balance Operating Program.

The balance operating program lets you adapt your balance to

various ambient conditions and to different weighing require-

ments and select the weight unit(s) commonly used in your

country. At the factory we have set the codes for a Standard

program, which is protected by a locking function to prevent ac-

cidental changes.

The "code" contains the information of the operating program,

It consists of three digits: one each for the page the line and the

word.

How to access the menu of the balance operating

program:

With the balance turned off (STANDBY state), hold down the

tare control (5) and simultaneously press the ON/OFF key (7).

Upon completion of the automatic self-test, release the tare

control as soon as "CH 5" is displayed. The Status of the bal-

ance operating program will be indicated in the weight display:

"L" Stands for the list mode. In this mode you can check the

menu code settings, but you cannot program new menu codes.

lf you wish to change a program menu code, you must first

unlock the menu access switch to access the menu.

To do so slide the menu access switch (4), located at the front

right of your balance, in the direction of the arrow.

The display will indicate "C", which Stands for the change

mode, meaning you can now proceed to make the necessary

code changes.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Sartorius Échelle

Sartorius

Sartorius Factory Series FC06BBE-S Manuel utilisateur

Sartorius

Sartorius PMA.Power Series Manuel utilisateur

Sartorius

Sartorius PMA.Quality PMA7501H Manuel utilisateur

Sartorius

Sartorius Combics CAPS..-LU Series Manuel utilisateur

Sartorius

Sartorius Signum: Option Y2 SIWR Instructions originales

Sartorius

Sartorius ISBBS Manuel utilisateur

Sartorius

Sartorius CW3P Manuel utilisateur

Sartorius

Sartorius Signum 1 Manuel utilisateur

Sartorius

Sartorius TS 12 Manuel utilisateur

Sartorius

Sartorius PMA.Evolution Manuel utilisateur

Sartorius

Sartorius Combics CAW3P Manuel utilisateur

Sartorius

Sartorius M-Power AZ214 Manuel utilisateur

Sartorius

Sartorius PMA.Power PMA35001 Manuel utilisateur

Sartorius

Sartorius M-Power AZ214 Manuel utilisateur

Sartorius

Sartorius PMA.Power Manuel utilisateur

Sartorius

Sartorius PMA.Evolution EVO1Y1 Manuel utilisateur

Sartorius

Sartorius BL150S Manuel utilisateur

Sartorius

Sartorius ME415S Manuel utilisateur

Sartorius

Sartorius U 4100 Manuel utilisateur

Sartorius

Sartorius Cubis MCA Fiche technique

Sartorius

Sartorius CPA 12001S Manuel utilisateur

Sartorius

Sartorius EVO1Y Manuel utilisateur

Sartorius

Sartorius PMA.Economy Manuel utilisateur

Sartorius

Sartorius Cubis MCE Series Manuel utilisateur

Manuels Échelle populaires d'autres marques

AWS

AWS ZEO-50 Manuel utilisateur

Gima

Gima Glass Body Fat Analyzer Manuel de la liste des pièces

Seca

Seca 374 Manuel utilisateur

TEC

TEC TEC SL59 SERIES Manuel utilisateur

Axis

Axis B/E Series Manuel utilisateur

Alecto

Alecto ACW-40 Manuel utilisateur

Rice Lake

Rice Lake MSI-4260 IS Manuel utilisateur

IKA

IKA RCT basic safety control Manuel utilisateur

ADE

ADE M20011 Manuel utilisateur

Duronic

Duronic KS3000 Manuel utilisateur

Digi

Digi SM-720 Manuel utilisateur

Cardinal

Cardinal CS Series Manuel utilisateur

Korona

Korona Kastella Manuel utilisateur

A&D

A&D FC-50Ki Manuel utilisateur

BDA

BDA CAMARGUE Manuel utilisateur

Tanita

Tanita HD-357 Manuel utilisateur

Leifheit

Leifheit 03173 Manuel utilisateur

Lumme

Lumme LU-1340 Manuel utilisateur