Sam4s Titan-560 Manuel utilisateur
One Blue Hill Plaza, 16th Floor, PO Box 1546
Pearl River, NY 10965
1-800-PC-AMERICA, 1-800-722-6374
(Voice) 845-920-0800 (Fax) 845-920-0880
Sam4s Titan-560 Installation Guide
This guide will show you how to setup your Sam4s Titan 560 all in one point of sale terminal. It will show
you where to connect your hardware on the terminal.
2
TABLE OF CONTENTS
CONNECTING THE POWER ADAPTER AND ROUTING YOUR PERIPHERAL CABLES 4
Important Notes:
The only editions of windows that was certified to work with this model is Windows 7 Pro 32bit or
64bit.
The only Sam4s accessory that has been certified to work with CRE is the Thin Silver MSR. No other
optional MSR or external display has been certified to work with CRE. To get a list of supported
certified hardware, refer to Supported Hardware Matrix.
3
Document Version
Date
Author
Description of Changes
1.0
January 3, 2018
Mathew Piccinich
1st Release
4
Connecting the Power Adapter and Routing your peripheral cables
1. To access the ports on the unit, you must remove the
plastic cover on the rear of the unit.
2. Locate the handle and lift straight up(not out) to
remove the cover.
3. If you are going to be connecting multiple peripherals
to the terminal, now is also a good time to remove
the back panel that covers the cable routing section.
Simply pull the panel straight back to remove it. The
image to the right is an example of what the cable
routing section looks like with the rear panel
removed.
4. Verify that the power adapter cable has been routed
through the casing of the terminal and that the plug
end is located by the ports.
5. Connect the plug to the port labeled DC-IN(19V)
5
6. Proceed to route your peripheral’s cable up through the cable routing hole into the cable routing section, similar
to how the power adapter cable is routed in the image on the left.
7. Route the cables up through the top of the cable routing section of the terminal, similar to how the power
adapter cable is routed in the image in the middle. Connect the peripheral cables to their correct ports. A diagram
and explanation of these ports will be in the next section
8. Route the section of the cable that connects to the peripheral through the hole on the bottom of the terminal
going out to the peripheral. Similar to the power cable in the image on the right.
LAN is used for Ethernet cables between your router/switch to the pos terminal for network/internet access.
LINE OUT is for external speakers
VGA is for connecting external displays
COM 1-3 can be used for various types of peripherals that require a serial/RS232 connection. When using these
ports be sure to remember the label of the COM port, it will be required for configuring the connected peripheral.
COM4 is used in conjunction with a special adapter to connect devices with a serial/RS232 connection.
Drawer used for connecting cash drawers to the terminal via a cash drawer cable
USB used for various types of peripherals.
***Ports that should not be touched unless instructed by a technician***
HDD –this holds the hard drive used by the terminal.
6
9. After connecting all of your peripherals place the port
cover and the routing section cover back onto the
terminal.
10. Connect the power adapter to an AC outlet
11. Look for the power button on the underside of the
terminal display on the right hand side, press it to
turn on the terminal.
12. The button will light up and the display show the
BIOS post screen followed by the windows boot up
screen.
Table des matières
Autres manuels Sam4s Terminal tactile
Sam4s
Sam4s SPS-500 Manuel utilisateur
Sam4s
Sam4s SAM4POS Manuel utilisateur
Sam4s
Sam4s SPT-3000 Mode d’emploi
Sam4s
Sam4s Touch Screen Terminal Manuel utilisateur
Sam4s
Sam4s SPS-500 Manuel utilisateur
Sam4s
Sam4s SPT-7000 Series Mode d’emploi
Sam4s
Sam4s SAP-630 Series Manuel utilisateur
Sam4s
Sam4s SAM4POS Manuel utilisateur
Sam4s
Sam4s SAP-6600II Manuel utilisateur
Sam4s
Sam4s SAP-6600 Manuel utilisateur
Manuels Terminal tactile populaires d'autres marques
Wincor Nixdorf
Wincor Nixdorf iPOS plus Advanced Manuel utilisateur
Ingenico
Ingenico AXIUM EX4000 Manuel utilisateur
Heisei Electronics
Heisei Electronics Q-POS 815 Manuel utilisateur
Amano
Amano MTX-15 Manuel utilisateur
FLOWBIRD
FLOWBIRD CWT Compact Touch Manuel utilisateur
Demco
Demco SP7 Manuel utilisateur
