Sainlogic FT0300 Manuel utilisateur
1
Sainlogic FT0300 Professional WIFI Weather
Station with Wireless 8 Channel Remote
Monitoring User Manual
1. Introduction
Thank you for your purchase of the FT0300 Professional WIFI Wireless
Weather station. The following user guide provides step by step
instructions for installation, operation and troubleshooting.
2. Warnings
Warning: Any metal object may attract a lightning strike, including
your weather station mounting pole. Never install the weather station
during a storm.
Warning: Installing your weather station in an elevated location
may result in injury or death. Safety goes first. Make sure your setup
and preparation is secure, and take no risks.
3. Getting Started
The FT0300 weather station consists of a display console (receiver), a
sensor array with Integrated Outdoor Transmitter and mounting
hardware.
Parts List
The FT0300 weather station consists of the following parts (as
referenced in Figure 1 ).
QTY
Item
Image
1
Display Console Frame
Dimensions (LxHxW):
215 x 22 x 158mm
LCD Dimensions (LxW):
170 x 125mm
2
1
Integrated Outdoor Transmitter
Dimensions
(LxHxW):330x150x280mm
1
Thermo-hygrometer transmitter
(FT007TH)
Dimensions (LxHxW): 114.5 x
50.0 x 19mm
1
Foot Mounting (with pole
insert)
Dimensions: 101x 76 x 32mm
1
Mounting Bracket Back Plate
(pole mount)
Dimensions: 76 x 102 x 38mm
1
Mounting Pole
Dimensions: 300 x 300 x
20mm
3
2
Pole mounting nuts (M3) / bolts
Ø3)
4
Pole mounting nuts (M5) / bolts
( Ø5)
4
Tapping screws
1
Manual
1
Power Adapter
Figure 1
3.2 Recommended Tools
●Precision screwdriver (for small Phillips screws)
●Compass or GPS (for wind direction calibration)
●Adjustable Wrench
●Hammer and nail for hanging remote thermo-hygrometer
transmitter.
4
3.3 Setup of Sensor
The following illustration shows the full segment for Thermo-Hygrometer
，WIND,RAIN and UV INDEX sensor. purposes only ,as shown in
Figure 2.
Figure 2
3.3.1 Insert batteries into the transmitter. Locate the battery
cover on the transmitter, push and open the battery compartment, as
show in Figure 3.
Figure 3
5
Remove the battery cover on the back of the sensor by removing the
set screw, as shown in Figure 4.
Figure 4
Inserting 3xAA batteries in the battery compartment, as show in Figure
5.
Figure 5
6
Close the battery cover. Make sure the gasket (around the battery
compartment) is properly seated in its place prior to closing the door.
Tighten the set screw.
Note: Do not install the batteries backwards. You can permanently
damage the sensors. The solar panel does not charge the batteries, so
rechargeable batteries are not needed or recommended.
Note: We recommend installing Lithium AA batteries for sensors.
The sensor LED indicator will light for 3 seconds, and then flash once
per 16 seconds thereafter. Each time it flashes, the sensor is
transmitting data.
Place the battery cover and push it to close the compartment.
Note: If the sensor does not power up after inserting the batteries,
press the reset button shown in Figure 6.
Figure 6
3.3.2 Insert batteries into the thermo-hygrometer
transmitter. Remove the battery cover on the back of the sensor by
removing the set screw, as shown in Figure 7.
7
Figure 7
1. BEFORE inserting the batteries, locate the dip switches on the
inside cover of the lid of the transmitter.
Figure 8 displays all four switches in the OFF position (factory
default setting).
Figure8
2. Channel Number: The FT0300 supports up to eight
transmitters. To set each channel number (the default is
Channel 1), change Dip Switches 1, 2 and 3, as referenced in
Table 1.
3. Temperature Units of Measure: To change the transmitter
display units of measure (°F vs. °C), change Dip Switch 4, as
referenced in Table 1.
8
DIP SWITCH
FUNCTION
1
2
3
4
DOWN
DOWN
DOWN
---
Channel 1
DOWN
DOWN
UP
---
Channel 2
DOWN
UP
DOWN
---
Channel 3
DOWN
UP
UP
---
Channel 4
UP
DOWN
DOWN
---
Channel 5
UP
DOWN
UP
---
Channel 6
UP
UP
DOWN
---
Channel 7
UP
UP
UP
---
Channel 8
---
---
---
DOWN
°F
---
---
---
UP
°C
Table 1
4. Insert two AAA batteries.
5. After inserting the batteries, the remote sensor LED indicator
will light for 4 seconds, and then flash once per 60 seconds
thereafter. Each time it flashes, the sensor is transmitting data.
6. Verify the correct channel number (CH) and temperature units
of measure (°F vs. °C) are on the display, as shown in Figure 9.
9
Figure 9
(1) temperature
(2) temperature units (°F vs. °C)
(3) channel number
(4) relative humidity
7. Close the battery cover. Make sure the gasket (around the
battery compartment) is properly seated in place prior to closing
the door. Tighten the set screw.
3.4 Display Console
3.4.1 Display Console Layout
The display console layout is shown in Figure 10
Note: The following illustration shows the full segment LCD display
for description purposes only and will not appear like this during normal
operation.
10
Figure 10
1. Outdoor temperature display
2. WIFI network
3. Outdoor humidity display
4. Outdoor humidity HI/LO alarm
icon
5. Min/Max reset for 24h icon
6. Rainfall display(RATE, 24h,
WEEK,MONTH, TOTAL)
7. Rainfall units of measure
8. Indoor temperature and
humidity HI/LO alarm icon
9. Indoor temperature and
humidity display
10. Time alarm icon
11. Time and date
12. Humidity units of measure (%)
13. UV Index display
14. Sunshine intensity
15. MOON phase
16. Sunlight units of measure
17. Sensor Heat index display
18. Sensor Heat index(heat index; dew
point)
19. Outdoor temperature and humidity
display
20. Scroll mode indicator
21. Channel 1-8 indicator
22. Pressure (REL and ABS) display
23. Pressure units of measure
24. Wind speed average display
25.Wind gust display
26.Wind speed units of measure
27.Wind chill and feels like HI/Lo alarm icon
28. Wind direction
29. OUT dew point and AT(Apparent
Temperature) display icon
30. Integrated outdoor transmitter Low power
indicator
31.Temperature units (°F or °C)
32.Outdoor temperature HI/LO alarm icon
33.Weather forecast
Ce manuel convient aux modèles suivants
9
Table des matières
Autres manuels Sainlogic Station météorologique
Sainlogic
Sainlogic WS-0835 Plus Professional Manuel utilisateur
Sainlogic
Sainlogic WS-0310 Manuel utilisateur
Sainlogic
Sainlogic FT0073 Manuel utilisateur
Sainlogic
Sainlogic WS0835 Manuel utilisateur
Sainlogic
Sainlogic FT0366 Manuel utilisateur
Sainlogic
Sainlogic SC089 Manuel utilisateur
Sainlogic
Sainlogic FT-0310 Manuel utilisateur
Sainlogic
Sainlogic WS0835 Manuel utilisateur
Sainlogic
Sainlogic FT0360 Manuel utilisateur
Sainlogic
Sainlogic FT0835 Manuel utilisateur
Manuels Station météorologique populaires d'autres marques
National Geographic
National Geographic VA Colour RC Manuel utilisateur
Renkforce
Renkforce 1208067 Manuel utilisateur
Levenhuk
Levenhuk Discovery Report WA40 Manuel utilisateur
Instant Transmission
Instant Transmission MA 10410 Manuel utilisateur
Lutron Electronics
Lutron Electronics PHB-318 Manuel utilisateur
WAREMA
WAREMA EWFS Weather station eco Manuel utilisateur