Runxin N74Q1 Manuel utilisateur

Multi-functional Flow Control Valve for

Water Treatment Systems

65510 (Old Model No.: N74Q1)

65610 (Old Model No.: N74Q3)

55510 (Old Model No.: N75Q1)

55610 (Old Model No.: N75Q3)

1. Basic Setting & Usage

1.1 The Function of PC Board

A. Button lock indicator

When the fourth decimal point of digital tube turns on, it indicates the

buttons are locked. At this moment any single button will not work (No

operation in one minute, the fourth decimal point of the digital tube will light

on and lock the buttons.)

Solution: Press and hold both and for 5 seconds until the decimal

point lights off.

B. Time of day indicator

When“:”flashes, it indicates the time of day.

C. Program mode indicator

The third decimal point of digital tube turns on, it indicates the program

display mode. Use or to view all values.

The third decimal point of digital tube flashes, it indicates the program set

mode. Use or to adjust all values.

D. Menu/Confirm button

Press to enter program display mode, the third decimal point of digital

tube turns on.

In program display mode, press to enter program set mode.

Parameters to be set will flash.

Press after all program are set successfully, and return to program

display mode.

E. Manual/Return button

In program display mode, press , it can proceed to next step.(Example:

press in service status, it will start regeneration cycles / washing

status instantly if the outlet water is unqualified; Press while it is in

regeneration / washing status, it will end regeneration/washing in

advance and go to the next status at once.)

F. Down and Up

In program display mode, press or to view all values.

In program set mode, press or to adjust values.

Press and hold both and for 5 seconds to unlock the buttons

In program set mode, press to return to program display mode; in

program display mode, press to return to menu mode.

Press while adjusting the values, then it will return to program display

mode directly without saving values. Press , it will save the values and

return to program display mode.

2. The Steps of Parameter Setting (Take N74Q3 A-01 as an

example)

Item

Process Steps

Symbol

Time of Day

1.In Time of Day display status, press to enter

program set mode, both hour value and ":" flash, press

and to adjust the hour value.

2. Press , minute value and ":" flash, press or

adjust the minute value.

3. Press to finish adjustment, press to return.

Regeneration

Time

1. Under the Regeneration Time display status, press to

enter into program set mode. Regeneration hour value

flashes, press or to adjust the hour value.

2.Press again, regeneration minute value flashes, press

or to adjust the minute value.

3. Press to finish adjustment, press to return.

Control Mode

1. Under the Control Mode display status, Press to

enter into program set mode.

Control mode A-01 flashes, press or to adjust the

working mode.

2. Press to finish adjustment, press to return.

Water

Treatment

Capacity

1. Under the Water Treatment Capacity display status,

Press enter into program set mode. Water treatment

capacity integer value flashes, press or to adjust

the value.

2.Press again, water treatment capacity decimal value

flashes, press or to adjust the decimal value.

3. Press to finish adjustment, press to return.

Backwash Time

1. Under the Backwash Time display status, Press

enter into program set mode. Backwash time value flashes,

press or to adjust the value.

2. Press to finish adjustment, press to return.

Brine & Slow

Rinse Time

1. Under the Brine& Slow Rinse Time display status, Press

enter into program set mode. Brine & slow rinse time

value flashes, press or to adjust the value.

2. Press to finish adjustment, press to return.

Brine Refill

Time

1. Under the Brine Refill Time display status, Press

enter into program set mode. Brine refill time value flashes,

press or to adjust the value.

2. Press to finish adjustment, press to return.

Fast Rinse

Time

1. Under the Fast Rinse Time display status, Press

enter into program set mode. Fast rinse time value flashes,

press or to adjust the value.

2. Press to finish adjustment, press to return.

Maximum

Interval

Regeneration

Days

1. Under the Maximum Interval Regeneration Days display

status, Press enter into program set mode. Maximum

interval regeneration days value flashes, press or

to adjust the value.

2. Press to finish adjustment, press to return.

Signal Output

Mode

1. Under the Signal Output Mode display status, Press

enter into program set mode. Signal output mode value

flashes, press or to adjust the value.

2. Press to finish adjustment, press to return.

For example, a softener has set fast rinse time as 12 minutes. After

regenerating, the chloridion in the outlet water is always higher than normal,

which indicate that fast rinse time is too short. If you want to set the time as

15 minutes, the modification steps as follows:

①Press and hold both and to unlock the button (The fourth

decimal point of digital tube lights off);

②Press , the third decimal point of digital tube lights on;

③Press or continuously until in fast rinse status, the digital

display area shows: 5-12M

④Press , 12 flashes

⑤Press the continuously, until 12 changesto 15

⑥Press again and hear a sound "Di", the frame stop flickering, the

program returns to inquiry status;

⑦If you want to adjust other parameters, you need to adjust as above

3-5 steps; if not, press to exit the program inquiry status and the screen

displays the current working status.

Ce manuel convient aux modèles suivants

Autres manuels Runxin Unité de contrôle

Runxin

Runxin F104 A Manuel utilisateur

Runxin

Runxin 51240B (F112BS) Manuel utilisateur

Runxin

Runxin 63518 Manuel utilisateur

Runxin

Runxin 63504 Manuel utilisateur

Runxin

Runxin F56A Manuel utilisateur

Runxin

Runxin 53520 Manuel utilisateur

Runxin

Runxin 73605 Manuel utilisateur

Runxin

Runxin F71B1 Manuel utilisateur

Runxin

Runxin 63510 Manuel utilisateur

Runxin

Runxin 51215 Manuel utilisateur

Runxin

Runxin 53515 Manuel utilisateur

Runxin

Runxin 17603 Manuel utilisateur

Runxin

Runxin 63504 Manuel utilisateur

Runxin

Runxin 55504 Manuel utilisateur

Runxin

Runxin F79A-LCD Manuel utilisateur

Runxin

Runxin F139 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur