Rosemount 702 Manuel utilisateur

Quick Start Guide

00825-0200-4702, rev. FA

December 2012

Rosemount 702 Wireless Discrete

Transmitter

December 2012

Quick Start Guide

NOTICE

This installation guide provides basic guidelines for the Rosemount® 702. It does not provide

instructions for detailed configuration, diagnostics, maintenance, service, troubleshooting, or

installations. Refer to the Rosemount 702 Reference Manual (Document Number

00809-0200-4702) for more instruction. This guide and the manual are available electronically

on www.rosemount.com.

Explosions could result in death or serious injury:

Installation of this transmitter in an explosive environment must be in accordance with the

appropriate local, national, and international standards, codes, and practices. Please review

the Product Certifications section for any restrictions associated with a safe installation.

Before connecting a Field Communicator in an explosive atmosphere, ensure the

instruments are installed in accordance with intrinsically safe or non-incendive field wiring

practices.

Electrical shock can result in death or serious injury

Avoid contact with the leads and terminals. High voltage that may be present on leads can

cause electrical shock.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

conditions. This device may not cause harmful interference. This device must accept any

interference received, including interference that may cause undesired operation.

This device must be installed to ensure a minimum antenna separation distance of 8 in. (20

cm) from all persons.

The power module may be replaced in a hazardous area. The power module has surface

resistivity greater than one gigaohm and must be properly installed in the wireless device

enclosure. Care must be taken during transportation to and from the point of installation to

prevent electrostatic charge build-up.

Shipping considerations for wireless products:

The unit was shipped to you without the power module installed. Please remove the power

module prior to shipping the unit.

Each power module contains two “C” size primary lithium batteries. Primary lithium batteries

are regulated in transportation by the U.S. Department of Transportation, and are also covered

by IATA (International Air Transport Association), ICAO (International Civil Aviation

Organization), and ARD (European Ground Transportation of Dangerous Goods). It is the

responsibility of the shipper to ensure compliance with these or any other local requirements.

Please consult current regulations and requirements before shipping.

Contents

Wireless considerations . . . . . .page 3

Physical installation . . . . . . . . . .page 5

Device network configuration . page 9

Verify operation . . . . . . . . . . . . page 10

Reference information: wiring switch

inputs, output circuits, and leak

sensors . . . . . . . . . . . . . . . . . . .page 14

Product Certifications . . . . . .page 31

Quick Start Guide

December 2012

Wireless considerations

Power up sequence

The Smart Wireless Gateway should be installed and functioning properly before

any wireless field devices are powered. Install the Black Power Module,

SmartPower™ Solutions model number 701PBKKF (part number

00753-9220-0001) into the Rosemount 702 transmitter to power the device.

Wireless devices should be powered up in order of proximity from the Gateway,

beginning with the closest device, then working outward from the Gateway. This

results in a simpler and faster network installation. Enable Active Advertising on

the Gateway to ensure that new devices are able to join the network faster. For

more information see the Smart Wireless Gateway Manual (Document No.

00809-0200-4420).

Antenna position

The antenna should be positioned vertically, either straight up or straight down,

and should be approximately 3 ft. (1 m) from any large structure, building, or

conductive surface to allow for clear communication to other devices.

Figure 1. Antenna Position

Conduit entries

Upon installation, ensure that each conduit entry is either sealed with a conduit

plug with appropriate thread sealant, or has an installed conduit fitting or cable

gland with appropriate thread sealant. Please note that the conduit entries on the

Rosemount 702 transmitter are threaded 1/2-14 NPT.

December 2012

Quick Start Guide

Figure 2. Conduit Entry

Field communicator connections

The Power Module needs to be installed before the Field Communicator can

interface with the Rosemount 702 transmitter. This transmitter uses the Black

Power Module; please order model number 701PBKKF or part number

00753-9220-0001.

Figure 3. Connection Diagram

Conduit Entry

COMM

P/N 00753-9200-0020

0020

CH1 +

CMN

CH2 +

CMN

CH Input Mode:

Dry Contact Only

CH Output Mode:

26VDC Max

100mA Max

Quick Start Guide

December 2012

The Rosemount 702 transmitter and all other wireless devices should not be set

up until after the Smart Wireless Gateway has been installed and is functioning

properly.

The Rosemount 702 transmitter can be installed in one of two configurations:

Direct Mount, where the switch is connected directly to the Rosemount 702

transmitter housing’s conduit entry, or Remote Mount, where the switch is

mounted separate from the Rosemount 702 transmitter housing, then

connected to the Rosemount 702 transmitter via conduit. Choose the installation

sequence that corresponds to the mounting configuration.

Step 1: Physical installation

Direct mount

Note

Direct mount installation should not be employed when using tubing and connectors such as

Swagelok®fittings.

1. Install the switch according to standard installation practices making sure to

use thread sealant on all connections.

2. Attach the Rosemount 702 transmitter housing to the switch using the

threaded conduit entry.

3. Attach the switch wiring to the terminals as indicated on the wiring diagram

(Figures on page 15 through page 30).

4. Connect the Black Power Module.

December 2012

Quick Start Guide

Note

Wireless devices should be powered up in order of proximity from the Smart Wireless Gateway,

beginning with the closest device to the Smart Wireless Gateway. This will result in a simpler and

faster network installation.

5. Close the housing cover and tighten to safety specification. Always ensure a

proper seal so that metal touches metal, but do not over tighten.

6. Position the antenna such that it is vertical, either straight up or straight down.

The antenna should be approximately 3-ft. (0.91 m) from any large structures

or buildings, to allow clear communication to other devices.

Remote mount

1. Install the switch according to standard installation practices making sure to

use thread sealant on all connections.

2. Run wiring (and conduit if necessary) from the switch to the Rosemount 702

transmitter.

3. Pull the wiring through the threaded conduit entry of the Rosemount 702

transmitter.

4. Attach the switch wiring to the terminals as indicated on the wiring diagram

(Figures on page 15 through page 30).

Possible antenna rotation shown.

Antenna rotation allows for best

installation practices in any

configuration.

Quick Start Guide

December 2012

5. Connect the Black Power Module.

Note:

Wireless devices should be powered up in order of proximity from the Smart Wireless Gateway,

beginning with the closest device to the Gateway. This will result in a simpler and faster network

installation.

6. Close the housing cover and tighten to safety specification. Always ensure a

proper seal so that metal touches metal, but do not over tighten.

7. Position the antenna such that it is vertical, either straight up or straight down.

The antenna should be approximately 3-ft. (0.91 m) from any large structures

or buildings, to allow clear communication to other devices.

High gain, remote antenna (optional)

The high gain, remote antenna options provide flexibility for mounting the

Rosemount 702 transmitter based on wireless connectivity, lightning protection,

and current work practices.

December 2012

Quick Start Guide

The high gain, remote mount antenna kit includes coaxial sealant for the cable

connections for the lightning arrestor and antenna.

Find a location where the remote antenna has optimal wireless performance.

Ideally this will be 15-25 ft. (4,6 - 7,6 m) above the ground or 6 ft. (2 m) above

obstructions or major infrastructure. To install the remote antenna use one of the

following procedures:

WN option

1. Mount the antenna on a 1.5-2 in. pipe mast using the supplied mounting

equipment.

2. Connect the lightning arrestor directly to the top of the Rosemount 702

transmitter.

3. Install the grounding lug, lock washer, and nut on top of lightning arrestor.

4. Connect the antenna to the lightning arrestor using the supplied LMR-400

coaxial cable ensuring the drip loop is not closer than 1 ft. (0.3 m) from the

lightning arrestor.

5. Use the coaxial sealant to seal each connection between the wireless field

device, lightning arrestor, cable, and antenna.

6. Ensure that the mounting mast and lightning arrestor are grounded according

to local/national electrical code.

Any spare lengths of coaxial cable should be placed in 12 in. (0,3 m) coils.

When installing remote mount antennas for the Rosemount 702 transmitter, always use established safety

procedures to avoid falling or contact with high-power electrical lines.

Install remote antenna components for the Rosemount 702 transmitter in compliance with local and

national electrical codes and use best practices for lightning protection.

Before installing, consult with the local area electrical inspector, electrical officer, and work area supervisor.

The Rosemount 702 transmitter remote antenna option is specifically engineered to provide installation

flexibility while optimizing wireless performance and local spectrum approvals. To maintain wireless

performance and avoid non-compliance with spectrum regulations, do not change the length of cable or

the antenna type.

If the supplied remote mount antenna kit is not installed per these instructions, Emerson Process

Management is not responsible for wireless performance or non-compliance with spectrum regulations.

Quick Start Guide

December 2012

Figure 4. Rosemount 702 Transmitter with high gain, remote antenna.

Note

Weather Proofing is Required! The remote mount antenna kit includes coaxial sealant for weather

proofing the cable connections for the lightning arrestor, antenna, and Rosemount 702

transmitter. Coaxial sealant must be applied to guarantee performance of the wireless field

network. Please see Figure 5 for details on how to apply coaxial sealant.

Figure 5. Applying coaxial sealant to cable connections

Step 2: Device network configuration

In order to communicate with the Smart Wireless Gateway, and ultimately the

host system, the transmitter must be configured to communicate with the

wireless network. This step is the wireless equivalent of connecting wires from a

transmitter to the information system. Using a Field Communicator or AMS

Wireless Configurator, enter the Network ID and Join Key so that they match the

Network ID and Join Key of the Gateway and other devices in the network. If the

Network ID and Join Key do not match that of the Gateway, the Rosemount 702

transmitter will not communicate with the network. The Network ID and Join Key

December 2012

Quick Start Guide

may be obtained from the Smart Wireless Gateway on the

Setup>Network>Settings page on the web interface, shown in Figure 6.

Figure 6. Gateway Network Settings

AMS Wireless Configurator

Right click on the Rosemount 702 transmitter and select Configure. When the

menu opens, select Join Device to Network and follow the method to enter the

Network ID and Join Key.

Field Communicator

The Network ID and Join Key may be changed in the wireless device by using the

following Fast Key sequence. Set both Network ID and Join Key.

Step 3: Verify operation

There are four ways to verify operation: using the optional local display (LCD),

using the Field Communicator, using the Smart Wireless Gateway’s integrated

web interface, or by using AMS® Suite Wireless Configurator. If the Rosemount

702 transmitter was configured with the Network ID and Join Key, and sufficient

time has passed, the transmitter will be connected to the network.

Function Key Sequence Menu Items

Wireless Setup 2,2,1 Network ID, Join Device to Network

Autres manuels pour 702

Table des matières

Autres manuels Rosemount Instrument de mesure

Rosemount

Rosemount 3095FB Manuel utilisateur

Rosemount

Rosemount 8712D Series Manuel utilisateur

Rosemount

Rosemount TankRadar Pro Manuel de la liste des pièces

Rosemount

Rosemount 1054B Manuel utilisateur

Rosemount

Rosemount 8800D Series Manuel utilisateur

Rosemount

Rosemount 8714D Manuel utilisateur

Rosemount

Rosemount 148 Manuel utilisateur

Rosemount

Rosemount P300 Manuel utilisateur

Rosemount

Rosemount 2130 Manuel utilisateur

Rosemount

Rosemount P330 Manuel utilisateur

Rosemount

Rosemount 2700 Manuel utilisateur

Rosemount

Rosemount 5401 Manuel utilisateur

Rosemount

Rosemount 8732C Manuel utilisateur

Rosemount

Rosemount 1195 Manuel utilisateur

Rosemount

Rosemount 6888Xi Manuel utilisateur

Rosemount

Rosemount 3051SFC_A Manuel utilisateur

Rosemount

Rosemount 8750WA Manuel utilisateur

Rosemount

Rosemount 8732 Series Manuel utilisateur

Rosemount

Rosemount 5708 Manuel utilisateur

Rosemount

Rosemount 1159 Manuel utilisateur

Rosemount

Rosemount Wireless Pressure Gauge Manuel utilisateur

Rosemount

Rosemount Series 8700 Manuel utilisateur

Rosemount

Rosemount 951C Manuel utilisateur

Rosemount

Rosemount 4500 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur