Rosemount 1195 Manuel utilisateur

Quick Start Guide

00825-0100-4686, Rev EA

June 2016

Rosemount™1195 Integral Orifice

Assembly

00825-0100-4686 EA.fm Page 1 Friday, June 17, 2016 4:39 PM

June 2016

Quick Start Guide

NOTICE

This document provides basic installation guidelines for the Rosemount1195. For comprehensive

instructions for detailed configuration, diagnostics, maintenance, service, installation, or troubleshooting

refer to the Rosemount 1195 Reference Manual. The manual and this guide are also available electronically

on EmersonProcess.com/Rosemount.

If the Rosemount 1195 Integral Orifice was ordered assembled to a Rosemount Pressure Transmitter, refer

to the following Quick Start Guides for information on configuration and hazardous locations certifications:

Rosemount 3051S Quick Start Guide

Rosemount 3051SMV Quick Start Guide

Rosemount 3051 Quick Start Guide

Rosemount 2051 Quick Start Guide

Process leaks may cause harm or result in death

To avoid process leaks, only use gaskets designed to seal with the corresponding flange and O-rings to seal

process connections.

Contents

Rosemount 1195 Integral Orifice Assembly

View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Location and orientation . . . . . . . . . . . . . . . . . . 4

Primary element orientation . . . . . . . . . . . . . . . 7

Primary element installation . . . . . . . . . . . . . . . 9

Preparing for operation . . . . . . . . . . . . . . . . . . 11

Product certifications . . . . . . . . . . . . . . . . . . . . 15

00825-0100-4686 EA.fm Page 2 Friday, June 17, 2016 4:39 PM

Quick Start Guide

June 2016

1.0 Rosemount 1195 Integral Orifice Assembly View

Figure 1. Traditional Body(1)

1. Transmitter and housing are shown for clarity purposes - only supplied if ordered.

A. Manifold

B. Gaskets

C. Studs

D. Nuts

E. Transmitter

F. Rosemount 1195 traditional body

G. Traditional orifice plate

00825-0100-4686 EA.fm Page 3 Friday, June 17, 2016 4:39 PM

June 2016

Quick Start Guide

Figure 2. Enhanced Support Body(1)

2.0 Location and orientation

Install the Rosemount 1195 Integral Orifice in the correct location within the

piping branch to prevent inaccurate measurement caused by flow disturbances.

2.1 Straight pipe length

Use the upstream (U) and downstream (D) lengths provided below in conjunction

with figures below to determine the appropriate upstream (U) and downstream

(D) pipe lengths. For example, for a 1-in. line size with a beta ratio (β) of 0.4 using

installation of Figure 4, the straight length of upstream piping required is

25 ⫻1 = 25-in., and downstream 10 ⫻1 = 10-in.

Note

The Rosemount 1195 Integral Orifice comes with the associated pipe lengths (18D

upstream and 8D downstream) when ordered with process pipe-end connections.

A. Manifold

B. Gaskets

C. Studs

D. Nuts

E. Transmitter

F. Rosemount 1195 enhanced support body

G. Enhanced support orifice plate

00825-0100-4686 EA.fm Page 4 Friday, June 17, 2016 4:39 PM

Quick Start Guide

June 2016

Straight run requirements(1)

Figure 3. Reducer

(2 d to d over a length of 1.5 d to 3 d)

Figure 4. Single 90° Bend Flow from One Branch

Figure 5. Two or More 90° Bends in Same Planes

Figure 6. Two or More 90° Bends in Different Planes

Figure 7. Expander

1. For dimensions, see Table 1 on page-6.

00825-0100-4686 EA.fm Page 5 Friday, June 17, 2016 4:39 PM

June 2016

Quick Start Guide

(0.5 d to d over a length of d to 2 d)

Figure 8. Ball/Gate Valve Fully Open

Table 1. Straight Run Requirements (in Pipe Diameters)

β(1)

1. Interpolation of intermediate β values can be used.

Figure 3

upstream

(U)

Figure 4

upstream

(U)

Figure 5

upstream

(U)

Figure 6

upstream

(U)

Figure 7

upstream

(U)

Figure 8

upstream

(U)

Figures 3–8(2)

On downstream

(D)

2. All straight lengths are expressed as multiples of the pipe inside diameter (d) and shall be measured from the upstream face of

orifice plate.

0.20 20 24 25 30 22 22 10

0.40 20 25 27 31 22 22 10

0.50 20 25 28 33 23 23 10

0.60 20 27 31 37 25 25 10

0.70 23 32 35 42 28 28 10

0.75 25 35 38 45 30 30 10

00825-0100-4686 EA.fm Page 6 Friday, June 17, 2016 4:39 PM

Quick Start Guide

June 2016

3.0 Primary element orientation

Figure 9. Rosemount 1195 Flowmeter Orientation with Traditional Style

Manifold

Gas (horizontal) Gas (vertical)

Liquid (horizontal) Liquid (vertical)

Steam (horizontal) Steam (vertical)

A. 90° recommended zone

B. Vertical plane

C. Horizontal plane

D. 360° recommended zone

E. Block valves

F. Vent valves

FLOW

00825-0100-4686 EA.fm Page 7 Friday, June 17, 2016 4:39 PM

June 2016

Quick Start Guide

Figure 10. Rosemount 1195 Flowmeter Orientation with Flange by Flange

Manifold

Gas (horizontal) Gas (vertical)

Liquid (horizontal) Liquid (vertical)

Steam (horizontal) Steam (vertical)

A. 120° recommended zone

B. Horizontal plane

C. Vertical plane

D. 360° recommended zone

E. Block valves

F. Vent valves

FLOW

00825-0100-4686 EA.fm Page 8 Friday, June 17, 2016 4:39 PM

Quick Start Guide

June 2016

Note

For saturated steam that is not high quality, it is recommended to mount in a vertical line to

avoid damming effect of the liquid.

4.0 Primary element installation

1. Ensure the side of the orifice plate marked “inlet” is facing upstream. This

stamping is found on the part of the orifice plate that extends beyond the

orifice bodies. Before pressurizing line, insure torque values shown below are

met. See Table 2 and Figure 11 for torque requirements of manifold studs and

orifice body studs. See the appropriate transmitter manual for torque

requirements of transmitter bolts.

Figure 11. Rosemount 1195 Assembly Fastener Naming Convention

Table 2. Stud and Nut Torque Specifications(1)(2)

1. Studs and nuts should be tightened to specification in two to three steps following a cross pattern.

2. Never reuse gaskets. Always replace gaskets after disassembly to ensure proper seal.

Manifold studs Torque

All Line sizes and gasket types 32 lb-ft.(44 N-m)

Orifice body studs Torque

All line sizes and gasket types 60 lb-ft. (82 N-m)

Traditional body Enhanced support body

Torque cross pattern

A. Transmitter bolts - 4⫻

B. Manifold studs - 4⫻

C. Orifice body studs - 2⫻

D. Orifice body studs - 4⫻

00825-0100-4686 EA.fm Page 9 Friday, June 17, 2016 4:39 PM

June 2016

Quick Start Guide

2. Units with flanged process connections:

a. Install the flanges in the process pipe. The distance between flanges should

be equal to the overall length of the flowmeter, plus clearance for gaskets.

b. Install the unit between the flanges, using studs, nuts, and gaskets

appropriate for the flange size/rating and process conditions. Proper

support is needed at the flange connections as shown below.

See Figure 12.

3. Units with threaded process conditions:

a. Install the unit using the appropriate threaded connection hardware.

4. Units with Socketweld Bodies:

a. To ensure perpendicularity of the pipe to the orifice fitting, the socket

diameter is smaller than the standard pipe OD. The pipe OD must be

machined-to-fit prior to welding.

b. To prevent damage, remove the transmitter prior to welding.

Figure 12. Recommended Support Locations for Installation

A. Support

B. No step

5. Once the Rosemount 1195 is installed ensure that it is supported properly and

take precautions to ensure that it is not used as a step. Refer to Figure 12 for

support locations.

00825-0100-4686 EA.fm Page 10 Friday, June 17, 2016 4:39 PM

Table des matières

Autres manuels Rosemount Instrument de mesure

Rosemount

Rosemount 702 Manuel utilisateur

Rosemount

Rosemount 5402 Manuel utilisateur

Rosemount

Rosemount 3308 Series Manuel utilisateur

Rosemount

Rosemount 405 Manuel utilisateur

Rosemount

Rosemount 8712D Series Manuel utilisateur

Rosemount

Rosemount 1054A pH Manuel utilisateur

Rosemount

Rosemount 1495 Manuel utilisateur

Rosemount

Rosemount 7D Manuel utilisateur

Rosemount

Rosemount Series 8700 Manuel utilisateur

Rosemount

Rosemount 8714D Manuel utilisateur

Rosemount

Rosemount 485 Annubar Manuel utilisateur

Rosemount

Rosemount 1151 Manuel utilisateur

Rosemount

Rosemount 1199 Manuel utilisateur

Rosemount

Rosemount Series 8700 Manuel utilisateur

Rosemount

Rosemount 2120 Manuel utilisateur

Rosemount

Rosemount 3300 Series Guide de configuration

Rosemount

Rosemount P300 Manuel utilisateur

Rosemount

Rosemount 1054B Manuel utilisateur

Rosemount

Rosemount TankRadar Rex RTG 3920 Manuel utilisateur

Rosemount

Rosemount 148 Manuel utilisateur

Rosemount

Rosemount 3051S Series Manuel utilisateur

Rosemount

Rosemount 702 Manuel utilisateur

Rosemount

Rosemount 2088 Manuel utilisateur

Rosemount

Rosemount 5081-P Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur