Rose electronics Vista DP KVM-4TDP/A1 Manuel utilisateur

Vista

1×4 KVM Switch • DisplayPort 4K@30 • USB2.0 • Audio

Installation

and

Operation Manual

10707 Stancliff Road

Houston, Texas 77099

Phone: (281) 933-7673

[email protected]

LIMITED WARRANTY

No part of this manual may be reproduced, stored in a retrieval system, or transcribed in any form or any means, electronic or mechanical, including photocopying and

recording, without the prior written permission of Rose Electronics.

manual-vista-dp-2018-04-19

Rose Electronics®warrants the Vista DP KVM Switch to be in good working order for one year from the date of

purchase from Rose Electronics or an authorized dealer. Should this product fail to be in good working order at

any time during this one-year warranty period, Rose Electronics will, at its option, repair or replace the Unit as

set forth below. Repair parts and replacement units will be either reconditioned or new. All replaced parts

become the property of Rose Electronics. This limited warranty does not include service to repair damage to

the Unit resulting from accident, disaster, abuse, or unauthorized modification of the Unit, including static

discharge and power surges.

Limited Warranty service may be obtained by delivering this unit during the one-year warranty period to Rose

Electronics or an authorized repair center providing a proof of purchase date. If this Unit is delivered by mail,

you agree to insure the Unit or assume the risk of loss or damage in transit, to prepay shipping charges to the

warranty service location, and to use the original shipping container or its equivalent. You must call for a return

authorization number first. Under no circumstances will a unit be accepted without a return authorization

number. Contact an authorized repair center or Rose Electronics for further information.

ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT INCLUDING THE WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO A

PERIOD OF ONE YEAR FROM THE DATE OF PURCHASE, AND NO WARRANTIES, WHETHER EXPRESS

OR IMPLIED, WILL APPLY AFTER THIS PERIOD. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW

LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.

IF THIS PRODUCT IS NOT IN GOOD WORKING ORDER AS WARRANTIED ABOVE, YOUR SOLE

REMEDY SHALL BE REPLACEMENT OR REPAIR AS PROVIDED ABOVE. IN NO EVENT WILL ROSE

ELECTRONICS BE LIABLE TO YOU FOR ANY DAMAGES INCLUDING ANY LOST PROFITS, LOST

SAVINGS OR OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF OR

THE INABILITY TO USE SUCH PRODUCT, EVEN IF ROSE ELECTRONICS OR AN AUTHORIZED DEALER

HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, OR FOR ANY CLAIM BY ANY OTHER

PARTY.

SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR

CONSEQUENTIAL DAMAGES FOR CONSUMER PRODUCTS, SO THE ABOVE MAY NOT APPLY TO YOU.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS

WHICH MAY VARY FROM STATE TO STATE.

TABLE OF CONTENTS

Contents

Disclaimer 1

System Introduction 1

Features 1

Package Contents 2

Additional Items that may be required 2

Vista DP Models 3

Installing the Vista DP Switch 4

Rackmount Kit: 4

Operation 5

Controlling the Vista DP 5

Front Panel Control 5

Hotkey Commands 5

Control using the RS-232 port 6

Establish a connection to the Vista DP switch 6

EDID Learning and Programming (HDMI Model Only) 7

Safety 8

Maintenance and Repair 9

Technical Support 9

Figures

Figure 1. Vista DP with DisplayPort Output 3

Figure 2. Vista DP with HDMI Output 3

Figure 3. Vista DP cabling layout diagram 4

Figure 4. Vista DP Rackmount 4

Figure 5. Front Panel Buttons 5

Figure 6. Examples of 9 pin RS-232 Straight Through and Crossed Cables 6

Figure 7. Identifying Serial Ports on Window Device Manager 6

Tables

Table 1. Keyboard hotkey and RS-232 serial port commands 5

Appendices

Appendix A —Specifications 10

Appendix B —Part Numbers 10

INTRODUCTION

Vista DP KVM Switch Manual 1

Disclaimer

While every precaution has been taken in the preparation of this manual, the manufacturer assumes no

responsibility for errors or omissions. Neither does the manufacturer assume any liability for damages resulting

from the use of the information contained herein. The manufacturer reserves the right to change the

specifications, functions, circuitry of the product, and manual content at any time without notice.

The manufacturer cannot accept liability for damages due to misuse of the product or other circumstances

outside the manufacturer’s control. The manufacturer will not be responsible for any loss, damage, or injury

arising directly or indirectly from the use of this product (See limited warranty).

System Introduction

Thank you for choosing the Vista DP. It is the result of Rose Electronics commitment to providing state-of-the-

art solutions for today’s demanding workplace. a dedicated multi-platform KVM switch. It is capable of

managing up to four 4K computers through a single managing computer. The Vista DP comes in two models -

one with a HDMI connection to the managing computer, and another one with a DisplayPort connection.

The Vista DP is DisplayPort 1.1 and HDMI compliant, and supports screen resolutions up to 4K Ultra-HD

(3840x2160 @ 30Hz. Up to four USB 2.0 devices can be connected to the unit which can be controlled by the

managing computer. The switch can be controlled through the Front Panel buttons or from the managing

computer through an RS-232 interface.

EDID pass-through and full USB and mouse emulation of all connected monitors, keyboards and mice allow for

smooth switching.

Features

■Supports DisplayPort video resolutions up to 3840×2160@30Hz

■Two models: DisplayPort in with DisplayPort or HDMI out

■Fully supports Windows, Mac, and Linux

■Supports USB2.0 devices and USB-HID keyboard/mouse

■Switchable stereo audio

■Access and control the switch via front panel push buttons, keyboard hot-keys or the serial RS-232 port

■Serial control interface via the DB9 serial port using the Rose RCS-4RS/D9 4-port remote control switch

■EDID learning and pass-through for all ports, enabling smooth and efficient video switching

■Independent switching and use of the KVM station and USB2.0 ports

■Complete keyboard/mouse emulation for error free booting of connected PC’s/servers

■DVI and HDMI video can be supported by using suitable cable adapters

■Made in USA

Vista DP KVM Switch Manual 2

Package Contents

The package contents consist of the following items:

■Vista DP Switch

■External power supply

■Power cable

■User Manual

Additional Items that may be required

■USB Type A to USB Type B M/M cable

■DisplayPort to DisplayPort M/M cable

■HDMI to HDMI M/M cable

■Stereo 3.5mm audio M/M cable

■Serial DB9 M/F cable

These cables can be ordered separately from Rose Electronics.

MODELS

Vista DP KVM Switch Manual 3

Vista DP Models

The Vista DP is offered in two models – one with a DisplayPort output, and the other with a HDMI output.

Front Panel

Rear Panel

Figure 1. Vista DP with DisplayPort Output

Front Panel

Rear Panel

Figure 2. Vista DP with HDMI Output

Vista DP KVM Switch Manual 4

Installing the Vista DP Switch

Installation of the Vista DP is very simple.

Figure 3. Vista DP cabling layout diagram

1. Ensure that power is disconnected from the Vista DP.

2. Connect the DisplayPort cables and USB cables (male-A to male-B) from the computers to the

respective ports on the Vista DP. Connect the audio cables if required.

3. Connect the USB keyboard and mouse on the two USB ports on the right labelled “KB/MS”. The two

USB ports on the right are dedicated for keyboard and mouse emulation only. The two USB ports on

the left are for other USB 2.0 peripherals (flash drives, printers, etc.)

4. Optionally connect speakers to the Audio-Out port located between the USB connectors and a serial

port controller to the serial port.

5. Connect the display monitor to the video out on the Vista DP, either DisplayPort or HDMI. Connect the

external 5V power supply and power on the Vista DP.

Rackmount Kit:

The Vista DP can be mounted on a 19” rack shelf, fitting only 1 unit per shelf.

Figure 4. Vista DP Rackmount

Vista DP KVM Switch Manual 5

Operation

Controlling the Vista DP

The computers on the Vista DP can be switched using the buttons on the Front Panel, through keyboard hot-

key commands, or RS-232 commands. The video, keyboard, and mouse can all be switched simultaneously or

independently of each other. Each of these are described below.

Front Panel Control

To switch ports using the front panel, press the ▲button to navigate up and ▼button for down.

Figure 5. Front Panel Buttons

Hotkey Commands

A Hotkey command is a keyboard sequence used to trigger an action on the Vista DP through the use of the

keyboard connected on the USB port of the Vista DP. To activate the hotkey sequence, press the CTRL key

twice and then enter the desired hotkey commands.

Commands Hotkeys RS-232 Control

Switch all devices (KVM, USB 2.0, and

Audio) [CTRL] [CTRL] m [port#] [ENTER] //m[port #][cr]

Switch KVM only [CTRL] [CTRL] c [port#] [ENTER] //c[port #][cr]

Switch audio only [CTRL] [CTRL] a [port#] [ENTER] //a[port #][cr]

Switch USB2.0 only [CTRL] [CTRL] u [port#] [ENTER] //u[port #][cr]

Switch analog audio only [CTRL] [CTRL] a [port#] [ENTER] //a[port #][cr]

EDID learning (Model with HDMI only) [CTRL] [CTRL] e [ENTER] //e[cr]

Same as front panel ▲button [CTRL] [CTRL]

↑

(up arrow key) n/a

Same as front panel ▼button [CTRL] [CTRL] ↓ (down arrow key) n/a

Reset [CTRL] [CTRL] r //r

Reset to factory defaults [CTRL] [CTRL] f //f

Table 1. Keyboard hotkey and RS-232 serial port commands

Vista DP KVM Switch Manual 6

Control using the RS-232 port

Controlling the Vista DP via RS-232 requires an RS-232 card installed on your computer or a USB to RS-232

adapter. Below are instructions on how to create an RS-232 connection between a PC and the Vista DP switch

Use a terminal client software to connect the host PC or notebook to the switch. Make sure to use

communication settings 9600 bps, N, 8, 1 No flow control.

Check the device and your PC to determine if you need a male to male or a male to female cable and how long

it needs to be. The Vista DP requires a straight through cable. You can use a Null Modem Adapter to convert a

crossed cable to a straight through cable. Examples of crossed and straight thorough cable pin-outs are shown

below. The standard maximum length for an RS-232 cable is 50 feet (15 meters).

Figure 6. Examples of 9 pin RS-232 Straight Through and Crossed Cables

Establish a connection to the Vista DP switch

1. Connect an RS-232 cable to the RS-232 connector on the PC.

2. Connect the other end of the cable to the RS-232 port of the Vista DP.

3. On Windows, use the Windows Control Panel / Device Manager to identify the COM port number. See

instructions and Figure 6 below.

4. Power on the device.

Figure 7. Identifying Serial Ports on Window Device Manager

Vista DP KVM Switch Manual 7

If you are using a USB to COM port adapter on a Windows PC and need to identify the COM port used, do the

following:

1. Click on the Windows Start button.

2. Click on Control Panel.

3. Click on Device Manager.

4. Click on the arrow next to Ports (COM & LPT).

You should see the name of your adapter and the COM port number in use.

EDID Learning and Programming (HDMI Model Only)

The Vista DP features plug-and-play EDID, making the switch easy to implement in virtually any application. As

soon as a user plugs in a monitor, the switch automatically learns and copies the EDID to all ports. The plug-

and-play EDID helps make switching hassle free and simple.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Rose electronics Changer

Rose electronics

Rose electronics x series Manuel utilisateur

Rose electronics

Rose electronics UltraMatrix EE4-4X16U Guide d'installation

Rose electronics

Rose electronics UltraVista Manuel utilisateur

Rose electronics

Rose electronics UEB-8UB Manuel

Rose electronics

Rose electronics UEB-8UB Manuel utilisateur

Rose electronics

Rose electronics Orion X OXS-CH288-00 Manuel utilisateur

Rose electronics

Rose electronics Porter PO-4P Manuel utilisateur

Rose electronics

Rose electronics Xtensys XTS-V16x64D16-L Manuel utilisateur

Rose electronics

Rose electronics KVM-4THD/4K Manuel utilisateur

Rose electronics

Rose electronics Vista L SERIES Manuel utilisateur

Rose electronics

Rose electronics ServeView 2X Manuel utilisateur

Rose electronics

Rose electronics VISTA DVI Manuel utilisateur

Rose electronics

Rose electronics Vista LC DVI Manuel utilisateur

Rose electronics

Rose electronics MultiVideo Manuel du propriétaire

Rose electronics

Rose electronics ServeView Pro Manuel utilisateur

Rose electronics

Rose electronics Vista Mini Manuel utilisateur

Rose electronics

Rose electronics UltraLink UL-DV3 Manuel utilisateur

Rose electronics

Rose electronics ServeView Pro SEB-8UB Manuel utilisateur

Rose electronics

Rose electronics Station Master Manuel utilisateur

Rose electronics

Rose electronics UltraConsole UC1-1X16U Manuel utilisateur

Rose electronics

Rose electronics MultiVideo MEB-4U2V Manuel utilisateur

Rose electronics

Rose electronics SuperSwitch SS-9 Manuel utilisateur

Rose electronics

Rose electronics VISTA DVI Manuel utilisateur

Rose electronics

Rose electronics SuperSwitch SS-9 Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur