Robertshaw RS9210 Manuel utilisateur

R S 9210

Installation Manual

Thermostat System Types

Thank you for purchasing a Robertshaw®thermostat. This manual will describe how to

install and test the Robertshaw RS9210 thermostat.

Gas, Oil, or Electric Heat with Air Conditioning

Heat Pumps (with or without auxiliary or emergency heat)

Multi-Stage Systems

Heat-Only, including for Floor and Wall-Furnace

Cool-Only

750 Millivolt Heating Systems

Table of Contents Page

Installation Location 2

Thermostat Quick Reference 3

Wallplate Installation 4

Wiring 5-12

Installer Setup Menu 13-17

Mounting & Battery Installation 18

Programming 19-22

Specications 23

Power Options

Battery Power

Hardwire (Common Wire)

IMPORTANT SAFETY INFORMATION

WARNING:

• Always turn off power at the main power

source by unscrewing fuse or switching

circuit breaker to the off position

before installing, removing, cleaning, or

servicing thermostat.

• Read all of the information in this manual

before installing or programming this

thermostat.

• This is a 24V AC low voltage thermostat.

Do not install on voltages higher than

30V AC.

• All wiring must conform to local and

national building and electrical codes

and ordinances.

• Do not short (jumper) across terminals

on the gas valve or at the system control

to test installation. This will damage the

thermostat and void the warranty.

INSTALLATION MANUAL

Install the thermostat 4 to 5 feet above the oor in an area with good

air circulation and average temperature.

For new installations, mount thermostat on an inside wall, 4-5 feet

above the oor. Do not install the thermostat in the following locations:

• Behind a Door

• In a Corner

• Near Air Vents

• In Direct Sunlight

• With an Outside Wall Behind the Thermostat

• Near any Heat or Steam Generating Fixtures

• Near any Concealed Pipes or Chimneys

Installation at these locations will affect thermostat operation.

INSTALLATION LOCATION

Getting to know your thermostat

THERMOSTAT QUICK REFERENCE

Mon

Room

Set At

SLEEP

LCD Screen

Fan Switch

System Switch

Temperature Set-Point Buttons

User Buttons

Easy Change Battery Door

Tech Set Sun Mon Tue Wed Thu Fri Sat

Step

Min Com On

Com DelayHeat

Set Time

Run Sched

Set Sched

Hold

Prev Step

Done WAKE RETURN

Cool Swing

Room

LEAVE

Hold

SLEEP

Filter

Set At

Displays the user

selected set-point

temperature.

Days of the week

and time.

Indicates the current

room temperature.

Programmable Time Periods:

This thermostat has 4

programmable time periods

per day.

Button Options

LCD

Hold: Is

displayed when

thermostat

program is

overridden.

Low Battery

Indicator:

Replace

batteries when

indicator is

shown.

NOTE: If

these icons

are ashing,

there is a

5-minute

delay for

compressor

protection.

System

Operation

Indicators:

The , or

icon will display

when the COOL,

HEAT, or (fan)

is on.

FAN

AUTO COOLON

OFF HEAT

EMH

Mercury Notice:

This product is mercury-free. However,

if this product is replacing a control

which contains mercury, it needs to

be disposed of properly. Contact your

local waste management authority for

instructions regarding recycling and

proper disposal of the control.

Caution:

Electrical Hazard

Disconnect power before installing

this product. Failure to do so can

cause electric shock or equipment

damage.

WALLPLATE INSTALLATION

For a vertical mount, put screws

on the top and bottom.

For a horizontal mount, put screws

on the left and the right.

Vertical mount

Horizontal mount

WIRING

1 Turn Off Power to Heating/Cooling System

2 Remove Old Thermostat

Heating/cooling system

power switch

Circuit breaker

box

Remove old thermostat but leave wallplate with wires attached.

Do not remove wallplate

Terminal

designation

WIRING

ELEC

GAS

3 Label Wires with Tags

Label the wires using the supplied wire labels

as you disconnect them.

Wiring Labels

Apply these wiring labels to each wire with the appropriate

terminal designation as you remove it from the existing

thermostat.

B B Y2 Y2

V/VR

AUX

V/VR

AUX

C C W/E W/E F F

L L O O P P

RH RH T T U U

W1 W1 W2 W2 W3 W3

X2 X2 Y Y Y1 Y1

4 Separate Wallplate from

New Thermostat

Remove wallplate from the new thermostat

and mount onto wall.

Wallplate

Wire Labels

Terminal designation

WIRING

5 Mount Wallplate for New Thermostat

Mount the new wallplate using the included screws and anchors.

Drill 3/16-in. holes for drywall

Drill 3/16-in. holes for plaster

WIRING

6 Connect Wires

Simply match wire labels.

If labels do not match letters on the thermostat, check “Alternate Wiring (Conventional Systems)”

on page 9 and connect to terminal as shown (see notes, below).

SCREW

INSERT WIRES AND

TIGHTEN SCREWS

Autres manuels pour RS9210

Table des matières

Autres manuels Robertshaw Thermostat

Robertshaw

Robertshaw 8625 Manuel utilisateur

Robertshaw

Robertshaw 8406 Manuel utilisateur

Robertshaw

Robertshaw 300-204 Manuel utilisateur

Robertshaw

Robertshaw 9400 Manuel utilisateur

Robertshaw

Robertshaw 7610 Manuel utilisateur

Robertshaw

Robertshaw 9610 Manuel utilisateur

Robertshaw

Robertshaw RS4110 Manuel utilisateur

Robertshaw

Robertshaw RS4110 Manuel utilisateur

Robertshaw

Robertshaw 9560 Manuel utilisateur

Robertshaw

Robertshaw RS321P Manuel utilisateur

Robertshaw

Robertshaw 300 series Manuel utilisateur

Robertshaw

Robertshaw Smart Sense Series Manuel utilisateur

Robertshaw

Robertshaw 5300 Series Guide d'installation et d'utilisation

Robertshaw

Robertshaw 300 series Mode d'emploi

Robertshaw

Robertshaw RS6000 Manuel utilisateur

Robertshaw

Robertshaw RS3210 Series Manuel utilisateur

Robertshaw

Robertshaw 9801i2 Manuel utilisateur

Robertshaw

Robertshaw 9515 Manuel utilisateur

Robertshaw

Robertshaw 9701i Manuel utilisateur

Robertshaw

Robertshaw 9500 Manuel utilisateur

Robertshaw

Robertshaw RS9110 Manuel utilisateur

Robertshaw

Robertshaw smart 3000 Manuel utilisateur

Robertshaw

Robertshaw RS9210 Manuel utilisateur

Robertshaw

Robertshaw 9701i2 Manuel utilisateur

Manuels Thermostat populaires d'autres marques

EWELLY

EWELLY EW-181 Manuel utilisateur

Prolon

Prolon T1100 Instructions d'installation

Computherm

Computherm Q20 Manuel utilisateur

Heatmiser

Heatmiser neoStat Manuel utilisateur

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manuel utilisateur

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manuel utilisateur

Saswell

Saswell SAS920XWHB-7-S-RF Mode d’emploi

Aircalo

Aircalo TFP1-ET85P2 Manuel utilisateur

Honeywell

Honeywell CM721 Manuel utilisateur

Carrier

Carrier DEBONAIR 33CS Manuel utilisateur

Lennox

Lennox iHarmony Zone Thermostat Instructions de montage

Gemtech

Gemtech GT7000 Mode d’emploi

Rollei

Rollei Smartes 45000 Manuel utilisateur

Sinope

Sinope TH1300RF Manuel utilisateur

Honeywell

Honeywell RLV4305 Manuel utilisateur

Honeywell

Honeywell Prestige 2.0 THX9421 Manuel utilisateur

NuTone

NuTone NTBZ48 Instructions d'utilisation d'origine

Stelpro

Stelpro MAESTRO ASMT402AD Manuel utilisateur