RIOTEC DC9257AN Manuel utilisateur

1

Quick Guide

-DC9257AP (with Battery)

-DC9257AN (without Battery)

1 H92P/H92N

Connect to micro USB port of OTG device

2 H92P/H92N

3



* Before you use it, please switch to "C" for battery charge for

3~4 hours.

*Under “C mode”, you can raise/lower soft-keyboard easily.



H92P Scan Holder is with Li-Ion battery inside. When in

charging, please use the original power adaptor of

smartphone (recommend). Through it, it charges both OTG

device and H92P internal battery at the same time. When in

low battery (Red LED flashing), please charge it

immediately.

LED Indicator Information

Green LED OFF Full charged (Charge mode)

Green LED ON Charging (Charge mode)

Red LED Flashing Low battery (Operation mode)

Attention: Under “Operation mode” please do not charging,

otherwise the OTG device's battery will be charging back to

H92P’s battery.



The touch trigger is in the central area of mini scanner. (for both side).

Please check the above drawing for your reference.

Installation

Before using scanner, please make sure that the OTG device is fully charged.

1. Under USB HID interface

** When plugged into OTG device, it will be recognized and begin to scan

the barcode.

2. Under USB Serial interface

** Please install PL-2303 driver into your OTG device first. PL-2303 driver

can be downloaded from Google Play

** Connect scanner to your OTG device, then, you can know which serial

port scanner connects to.

** The data you scan will be sent to serial port and your APP can get the

data from serial port directly.

Trigger

Area

Suction Cup

PU Glue

(Can be used

repeatedly)

Micro USB

cable (OTG)

Mini

scanner

Micro USB

H92P with

Li- Ion Battery/

H92N without

Battery

Micro USB

LED Indicator

H92P only

O = Operation mode C = Char

e mode

LED Indicator

H92P only

2

Reset Configuration to Defaults

If you are unsure of the scanner configuration or have scanned the

incorrect codes, please from A1 to A7 for USB HID or B1 to B7 for USB

Serial. This will reset the scanner to its factory defaults.

USB HID USB Serial

A1 B1

A2 B2

A3 B3

A4 B4

A5 B5

A6 B6

A7 B7

Note: Please install PL-2303 driver for USB Serial.

Barcode Configuration Method:

(Flow chart for setup procedure :)

Start

Configuration

End

Configuration

Keyboard Language(For USB HID only)

Scan the appropriate country code as below to program the keyboard

layout for your country or language. As a general rule, the following

characters are supported, but need special care for countries other

than the United States: @ | $ # { } [ ] = / ‘ \ < > ~

USA

(Original setting)

Japan

Denmark

Finland

France

Germany

Italy

Norway

1D Symbologies – 1

ENABLE

CODE 39 DISABLE

ENABLE

CODE 39

FULL ASCII

DISABLE

ENABLE

CODE 39 Transmit

Start/Stop Character DISABLE

ENABLE

UPC-E DISABLE

ENABLE

UPC-A DISABLE

ENABLE

Interleaved

25 DISABLE

ENABLE

Matrix

25 DISABLE

ENABLE

Industrial 25 DISABLE

ENABLE

CODE 93 DISABLE

3

Barcode Configuration Method:

(Flow chart for setup procedure :)

Start

Configuration

End

Configuration

1D Symbologies – 2

ENABLE CODABAR DISABLE

ENABLE CODE 128

DISABLE

ENABLE

GS1-128

UCC/EAN-128

DISABLE

ENABLE MSI DISABLE

1D Symbologies – 3

ENABLE CODE 11 DISABLE

ENABLE

GS1-Databar

(RSS) DISABLE

ENABLE

GS1-Databar

(RSS-Limited) DISABLE

ENABLE

GS1-Databar

(RSS-Expand) DISABLE

ENABLE ISSN DISABLE

ENABLE ISBN DISABLE

ENABLE EAN-8

DISABLE

ENABLE EAN-13

DISABLE

Inter-Keystroke Delay (FOR USB HID Only)

This parameter specifies the delay between emulated keystrokes

No Delay Short Delay

(5ms)

Medium Delay

(10ms)

Long Delay

(15ms)

 Information in this document is subject to change without notice.

Q_200325_01

Ce manuel convient aux modèles suivants

Autres manuels RIOTEC Lecteur de codes-barres

RIOTEC

RIOTEC iLS6307JBQ Manuel utilisateur

RIOTEC

RIOTEC OM7228J Manuel utilisateur

RIOTEC

RIOTEC iDC9273A Manuel utilisateur

RIOTEC

RIOTEC LS6302A Manuel utilisateur

RIOTEC

RIOTEC RIOSCAN Manuel utilisateur

RIOTEC

RIOTEC iLS6300JB Manuel utilisateur

RIOTEC

RIOTEC LS6007 Manuel utilisateur

RIOTEC

RIOTEC DC9257AP Manuel utilisateur

RIOTEC

RIOTEC iLS6308KBQ Manuel utilisateur

RIOTEC

RIOTEC RIOSCAN iLS6300FS Manuel utilisateur

RIOTEC

RIOTEC iDC9507A Manuel utilisateur

RIOTEC

RIOTEC iDC9607L Manuel utilisateur

RIOTEC

RIOTEC iDC9502N Manuel utilisateur

RIOTEC

RIOTEC RIOSCAN iCR6307AS Manuel utilisateur

RIOTEC

RIOTEC iLS6303XBQ Manuel utilisateur

RIOTEC

RIOTEC iDC9607LW Manuel utilisateur

RIOTEC

RIOTEC DC9250DP Manuel utilisateur

RIOTEC

RIOTEC DC9270D Manuel utilisateur

RIOTEC

RIOTEC iDC9602A Manuel utilisateur

RIOTEC

RIOTEC LS6300E Manuel utilisateur

RIOTEC

RIOTEC iLS6307LB Manuel utilisateur

RIOTEC

RIOTEC DC9257LP Manuel utilisateur

RIOTEC

RIOTEC iDC9600C Manuel utilisateur

RIOTEC

RIOTEC iDC9607AW Manuel utilisateur

Manuels Lecteur de codes-barres populaires d'autres marques

POSMicro

POSMicro Datalogic PowerScan D7100 Manuel utilisateur

Marson

Marson MT780 Guide de configuration rapide

NCR

NCR RealPOS Manuel utilisateur

Motorola

Motorola SE3300 Guide de configuration rapide

Element

Element P130BT Manuel utilisateur

Motorola

Motorola Symbol LS3008 Manuel d'installation et d'exploitation

Meec tools

Meec tools OBD-II / VAG Manuel utilisateur

SICK

SICK CLP 100 Manuel utilisateur

Royal Tag SA

Royal Tag SA I-Read Manuel utilisateur

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuel utilisateur

Meteor

Meteor 8310 Manuel utilisateur

Denso

Denso BHT-500B Manuel utilisateur

Datalogic

Datalogic Heron HD3130 Manuel utilisateur

Motorola

Motorola MP6000 Instructions de montage

Newland

Newland NLS-HR15-BT Manuel utilisateur

ARTDEV

ARTDEV AS-1310 Manuel utilisateur

Aopos

Aopos AS290 Manuel utilisateur

ENS

ENS 367-5455 Manuel utilisateur