RIOTEC DC9277A Manuel utilisateur

1

Quick Guide

-DC9277A

Connect to micro USB port of OTG device

* Before you use scanner, please switch to "C" for battery

charge for 3~4 hours.

* Under “C mode”, you can raise/lower soft-keyboard

easily. (For USB HID only)

DC9277A is with Li-Ion battery inside. When in charging,

please use the original power adaptor of OTG device

(recommend). Through it, it charges both OTG device and

DC9277A internal battery at the same time. When in low

battery (Red LED flashing), please charge it immediately.

LED Indicator Information

Green LED OFF Full charged (Charge mode)

Green LED ON Charging (Charge mode)

Red LED Flashing Low battery (Operation mode)

Attention: Under “operation mode” please do not charging,

otherwise the OTG device's battery will be charging back to

DC9277A’s battery.



The touch sensor area is around the central area. There are 2

button trigger on the right and left side.

Please check the above drawing for your reference.

Installation

Before using scanner, please make sure that the OTG device is

fully charged.

1. Under USB HID interface

** When plugged into OTG device, it will be recognized and

begin to scan the barcode.

2. Under USB Serial interface

** Please install PL-2303 driver into your OTG device first.

PL-2303 driver can be downloaded from Google Play

** Connect scanner to your OTG device, then, you can

know which serial port scanner connects to.

** The data you scan will be sent to serial port and your

APP can get the data from serial port directly.

Suction Cup

PU Glue

(Can be used

repeatedly)

Micro USB

cable (OTG)

Li- Ion Battery

Button Trigger

O=Operation mode

Exit Windo

C=Char

e mode

Touch Trigger Area

Button Trigger

Char

e port

Indicator

(

LED

)

Indicator

(

LED

)

2

Reset Configuration to Defaults

If you are unsure of the scanner configuration or have

scanned the incorrect codes, please scan from A1 to A7 for

USB HID or B1 to B7 for USB Serial. This will reset the scanner

to its factory defaults.

USB HID USB Serial

A1 B1

A2 B2

A3 B3

A4 B4

A5 B5

A6 B6

A7 B7

Note: Please install PL-2303 driver for USB Serial.

Barcode Configuration Method:

(Flow chart for setup procedure :)

Start

Configuration

End

Configuration

Keyboard Language(For USB HID only)

Scan the appropriate country code as below to program the

keyboard layout for your country or language. As a general

rule, the following characters are supported, but need special

care for countries other than the United States:

@ | $ # { } [ ] = / ‘ \ < > ~

USA

(Original setting)

Japan

Denmark

Finland

France

Germany

Italy

Norway

1D Symbologies – 1

ENABLE

CODE 39 DISABLE

ENABLE

CODE 39

FULL ASCII

DISABLE

ENABLE

CODE 39 Transmit

Start/Stop Character DISABLE

ENABLE

UPC-E DISABLE

ENABLE

UPC-A DISABLE

ENABLE

Interleaved

25 DISABLE

ENABLE

Matrix

25 DISABLE

ENABLE

Industrial 25 DISABLE

ENABLE

CODE 93 DISABLE

ENABLE

CODABAR DISABLE

3

Barcode Configuration Method:

(Flow chart for setup procedure :)

Start

Configuration

End

Configuration

1D Symbologies – 2

ENABLE CODE 128

DISABLE

ENABLE

GS1-128

UCC/EAN-128

DISABLE

ENABLE MSI DISABLE

1D Symbologies – 3

ENABLE CODE 11 DISABLE

ENABLE

GS1-Databar

(RSS) DISABLE

ENABLE

GS1-Databar

(RSS-Limited) DISABLE

ENABLE

GS1-Databar

(RSS-Expand) DISABLE

ENABLE ISSN DISABLE

ENABLE ISBN DISABLE

ENABLE EAN-8

DISABLE

ENABLE EAN-13

DISABLE

Inter-Keystroke Delay (For USB HID Only)

This parameter specifies the delay between emulated

keystrokes

No Delay

Short Delay

(5ms)

Medium Delay

(10ms)

Long Delay

(15ms)

 Information in this document is subject to change without notice.

 For more information, please visit:

www.riotec.com.tw

R_180504_01

Autres manuels RIOTEC Lecteur de codes-barres

RIOTEC

RIOTEC LS6320E Manuel utilisateur

RIOTEC

RIOTEC DC9257AP Manuel utilisateur

RIOTEC

RIOTEC iDC9502K Manuel utilisateur

RIOTEC

RIOTEC iDC9607A Manuel utilisateur

RIOTEC

RIOTEC LS6300E Manuel utilisateur

RIOTEC

RIOTEC iDC9600C Manuel utilisateur

RIOTEC

RIOTEC RIOSCAN iLS6300FS Manuel utilisateur

RIOTEC

RIOTEC iDC9607LW Manuel utilisateur

RIOTEC

RIOTEC LS6322A Manuel utilisateur

RIOTEC

RIOTEC OM7320 Manuel utilisateur

RIOTEC

RIOTEC iDC9602NW Manuel utilisateur

RIOTEC

RIOTEC OM7220J Manuel utilisateur

RIOTEC

RIOTEC iDC9278K Manuel utilisateur

RIOTEC

RIOTEC LS6300V Manuel utilisateur

RIOTEC

RIOTEC RIOSCAN iLS6300FS Manuel utilisateur

RIOTEC

RIOTEC iDC9607L Manuel utilisateur

RIOTEC

RIOTEC DC9257L Manuel utilisateur

RIOTEC

RIOTEC LS6302A Manuel utilisateur

RIOTEC

RIOTEC iDC9608KW Manuel utilisateur

RIOTEC

RIOTEC RIOSCAN iLS6308KS Manuel utilisateur

RIOTEC

RIOTEC DC9273A Manuel utilisateur

RIOTEC

RIOTEC iLS6303XBU Manuel utilisateur

RIOTEC

RIOTEC iLS6300VBQ Manuel utilisateur

RIOTEC

RIOTEC DC9250 Manuel utilisateur

Manuels Lecteur de codes-barres populaires d'autres marques

POSMicro

POSMicro Datalogic PowerScan D7100 Manuel utilisateur

Marson

Marson MT780 Guide de configuration rapide

NCR

NCR RealPOS Manuel utilisateur

Motorola

Motorola SE3300 Guide de configuration rapide

Element

Element P130BT Manuel utilisateur

Motorola

Motorola Symbol LS3008 Manuel d'installation et d'exploitation

Meec tools

Meec tools OBD-II / VAG Manuel utilisateur

SICK

SICK CLP 100 Manuel utilisateur

Royal Tag SA

Royal Tag SA I-Read Manuel utilisateur

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuel utilisateur

Meteor

Meteor 8310 Manuel utilisateur

Denso

Denso BHT-500B Manuel utilisateur

Datalogic

Datalogic Heron HD3130 Manuel utilisateur

Motorola

Motorola MP6000 Instructions de montage

Newland

Newland NLS-HR15-BT Manuel utilisateur

ARTDEV

ARTDEV AS-1310 Manuel utilisateur

Aopos

Aopos AS290 Manuel utilisateur

ENS

ENS 367-5455 Manuel utilisateur