Ricoh Capella-NB1e Manuel utilisateur

Capella-NB1e

(Machine Code: G829)

SERVICE MANUAL

4 June 2005

Subject to Change

IMPORTANT SAFETY NOTICES

1. Before disassembling or assembling parts of the network scanning box,

make sure that the network scanning box power cord is unplugged.

2. The wall outlet should be near the network scanning box and easily

accessible.

3. The output voltage of the PSU (Power Supply Unit) can be either 100 ~ 240

Vac, without any adjustment. Make sure that the above voltage is used.

4. The power cord should be an approved type, in accordance with the

regulations for the country in which the network scanning box is used.

5. When keeping used lithium batteries in order to dispose of them later, do not

put more than 100 batteries per sealed box. Storing larger numbers or not

sealing them apart may lead to chemical reactions and heat buildup.

Lithium Batteries (Memory Back-up)

CAUTION

The danger of explosion exists if a battery of this type is incorrectly

replaced.

Replace only with the same or an equivalent type recommended by the

manufacturer. Discard used batteries in accordance with the

manufacturer’s instructions.

Maintenance Information

The operating instructions explains how to use and maintain the network scanning

Box . Before performing the maintenance, read the operating instructions.

Warning concerning copyright

Many documents are copyrighted. Such documents may not be reproduced by

scanning or in any other form without the express permission of the copyright

holder.

Notice

The contents of this manual are subject to change without notice.

This manual uses several symbols.

Symbol What it means

Refer to section number

See Core Tech Manual for details

Screw

Connector

E-ring

Clip ring

TABLE OF CONTENTS

1. REPLACEMENT AND ADJUSTMENT ............................................1

1.1 SPECIAL TOOLS ......................................................................................... 1

1.2 REPLACEMENT........................................................................................... 1

1.2.1 REPLACING THE MCBU BOARD (MAIN CONTROLLER BOARD) ... 1

1.2.2 REMOVING THE OPERATION PANEL BOARD,

KEY TOP, LCD BOARD AND LED CONTROL BOARD ...................... 3

2. TROUBLESHOOTING .......................................................................

2.1 SC CODES................................................................................................... 7

3. SERVICE TABLES...........................................................................8

3.1 DIP SWITCH FUNCTION ............................................................................. 8

3.2 SERVICE PROGRAM MODE....................................................................... 8

3.2.1 SP MODE DESCRIPTION................................................................... 8

Entering the service mode ....................................................................... 8

3.2.2 FIRMWARE UPDATE........................................................................ 11

Network firmware update ....................................................................... 11

3.2.3 BACKUP AND RESTORE SD CARD ................................................ 11

Backup SD card procedure.................................................................... 11

Restore SD card procedure ................................................................... 12

SPECIFICATIONS...............................................................................13

14 June, 2005 REPLACEMENT AND ADJUSTMENT

Spec.

1. REPLACEMENT AND ADJUSTMENT

CAUTION

Turn off the main power switch and disconnect the machine’s power cord

before you do the procedures in this section.

1.1 SPECIAL TOOLS

No special tool required for this model

1.2 REPLACEMENT

1.2.1 REPLACING THE MCBU BOARD (MAIN CONTROLLER

BOARD)

1. Remove the three screws from the lower cover.

2. Pull down the lower cover and detach it from the four hooks.

3. Open the upper and lower covers, as shown in the photograph below.

Important: Be careful not to damage the flat cable.

4. Disconnect the flat cable from the MCBU board connector.

Note: In the photograph below, the MCBU board is on the left side.

REPLACEMENT AND ADJUSTMENT 14 June, 2005

5. Remove the bracket (x 2).

6. Remove the MCBU board (x 4).

14 June, 2005 REPLACEMENT AND ADJUSTMENT

Spec.

1.2.2 REMOVING THE OPERATION PANEL BOARD, KEY TOP,

LCD BOARD AND LED CONTROL BOARD

1. Do Steps 1-4 of section 2.2.1.

2. Remove the operation panel board from the upper cover (x 11, x2).

REPLACEMENT AND ADJUSTMENT 14 June, 2005

3. Remove the key top.

14 June, 2005 REPLACEMENT AND ADJUSTMENT

Spec.

4. Remove the LCD board.

REPLACEMENT AND ADJUSTMENT 14 June, 2005

5. Remove the LED control board (x 2).

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Ricoh Scanner

Ricoh

Ricoh Scanner Manuel utilisateur

Ricoh

Ricoh IS330DC - IS - Flatbed Scanner Manuel utilisateur

Ricoh

Ricoh IS200e Manuel utilisateur

Ricoh

Ricoh Wide Format Color Scanner Manuel utilisateur

Ricoh

Ricoh Aficio IS420 Manuel utilisateur

Ricoh

Ricoh Priport JP1010 Manuel utilisateur

Ricoh

Ricoh IS760 Manuel utilisateur

Ricoh

Ricoh IS01 - IS 01 Manuel utilisateur

Ricoh

Ricoh IS100e Manuel utilisateur

Ricoh

Ricoh HS2P PLUS Manuel utilisateur

Ricoh

Ricoh fi-70F Manuel

Ricoh

Ricoh IS430 Manuel utilisateur

Ricoh

Ricoh IS450DE Manuel utilisateur

Ricoh

Ricoh Scanner Manuel utilisateur

Ricoh

Ricoh ImageReader FB735 Manuel utilisateur

Ricoh

Ricoh IS200e Manuel utilisateur

Ricoh

Ricoh Aficio 2105 Manuel utilisateur

Ricoh

Ricoh fi-8040 Manuel d'utilisation et d'entretien

Ricoh

Ricoh ImageReader PowerScan FB750 Manuel utilisateur

Ricoh

Ricoh Printer Manuel utilisateur

Ricoh

Ricoh C2828 Manuel d'instructions et de sécurité

Ricoh

Ricoh IS100e Manuel utilisateur

Ricoh

Ricoh Priport JP1030 Manuel utilisateur

Ricoh

Ricoh G410 Manuel utilisateur

Manuels Scanner populaires d'autres marques

Plustek

Plustek Scanner Manuel utilisateur

Z/I Imaging

Z/I Imaging PhotoScan 2001 Manuel utilisateur

Renkforce

Renkforce DS100-5M Manuel utilisateur

Image Access

Image Access WideTEK A2 Manuel utilisateur

Canon

Canon imageFORMULA CR-120N Manuel utilisateur

Fujitsu

Fujitsu FI-4860C2 Manuel utilisateur

GeoSlam

GeoSlam ZEB Horizon Instructions d'installation

Kodak

Kodak i5800 Scanner Manuel utilisateur

Kodak

Kodak i7300 Manuel utilisateur

Revopoint

Revopoint POP Manuel utilisateur

Fujitsu

Fujitsu fi-4860C Manuel utilisateur

Eddyfi Technologies

Eddyfi Technologies Floormap X Manuel utilisateur

Faselase

Faselase F6 Manuel utilisateur

Fujitsu

Fujitsu CardMinder Manuel utilisateur

Uniden

Uniden BC340CRS Manuel utilisateur

Infinite Peripherals

Infinite Peripherals INFINEA TAB M Manuel utilisateur

Mustek

Mustek PageExpress 4800 Pro Manuel utilisateur

Optex

Optex 750830 Manuel utilisateur