Ricatech RTT88 Manuel utilisateur
USER MANUAL
GEBRUIKERSHANDLEIDING
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
MANUALE D’USO
RTT88 Turntable
WARNING :
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE. DO NOT REMOVE COVER.
PILOT LAMPS SOLDERED IN PLACE. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
English
“Ventilation not being impeded.”
“Do not exposed to dripping or splashing and that no objects lled with liquids, such
as vases, shall be placed on the apparatus.”
Specication
FREQUENCY : FM 88 -108 MHz
AM 530 - 1600 KHz
USB Port 2.0 : Full Speed 512MB - 4GB (Support FAT16, FAT32)
POWER SOURCE : AC230V/50Hz
ANTENNA : External antenna for FM
Built-in ferrite bar for AM
POWER CONSUMPTION : 15W
SPEAKER SIZE : 2” x 3” Dynamic type x 2
SPEAKER OHM : 4 ohm
SPEAKER WATT : 3-5W
POWER OUTPUT : 1.2W x 2
* DESIGN AND SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.
The lighting ash with arrow-
head symbol, within an
equilateral triangle, is intend-
ed to alert user to the pres-
ence of uninsulated
“dangerous voltage” within the
product’s enclosure that may
be of sufcient magnitude to
constitute risk of electric
shock to persons.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER -
SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The exclamation point within
an equilateral triangle is in-
tended to alert user to the
presence of important
operating and maintenance
(servicing) instruction in the
literature accompanying
the appliance.
RRIISSKK OOFF EELLEECCTTRRIICC SSHHOOCCKK
DDOO NNOOTT OOPPEENN
CAUTION
IMPORTANT SAFEGUARDS FOR AUDIO PRODUCTS
PLEASE READ CAREFULLY THE FOLLOWING IMPORTANT SAFEGUARDS THAT ARE
APPLICABLE TO YOUR EQUIPMENT.
1. Read Instructions - All the safety and operating instructions should be read before
the appliance is operated.
2. Retain Instructions - The safety and operating instructions should be retained for
future reference.
3. Heed Warnings - All warnings on the appliance and in the operating instructions
should be adhered to.
4. Follow Instructions - All operating and use instructions should be followed.
5. Water and Moisture - The appliance should not be used near water-for example, near
a bathtub,washbowl,kitchen sink,laundry tub, in a wet basement, or near a
swim ming pool and the like.
6. Carts and Stands - The appliance should be used only with a cart or stand that is
recommended by the manufacturer.
6A.An appliance and cart combination should be moved with care. Quick stops,
excessive force, and uneven surfaces may cause the appliance and cart
combination to overturn.
7. Wall or Ceiling Mounting - The appliance should be mounted to a wall or ceiling
only as recommended by the manufacturer.
8. Ventilation - The appliance should be situated so that its location or position does
not interfere with-its proper ventilation.For example, the appliance should not be
situated on a bed, sofa, rug,or similar surface that may block the ventilation
openings or, placed in a built-in installation, such as a bookcase or cabinet that may
impede the ow of air through the ventilation openings.
9. Heat - The appliance should be situated away from heat sources such as
radiators,heat registers, stoves,or other appliances (including ampliers) that
produce heat.
10.Power Sources - The appliance should be connected to a power supply only of the
type described in the operating instructions or as marked on the appliance.
11.Grounding or Polarization - Precautions should be taken so that the grounding or
polarization means of an appliance is not impeded.
12.Power - Cord Protection - Power-supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or against them, paying
particular attention to cords at plugs, and the point where they exit from the
appliance.
13.Cleaning - The appliance should be cleaned only as recommended by the
manufacturer.
14.Antenna -This product is designed for use with the antenna attached and should not
be connected to any other external antennas.
15.Non-use Periods - The power cord of the appliance should be unplugged from the
outlet when left unused for a long period of time.
16.Object and Liquid Entry - Care should be taken so objects do not fall and liquids
are not spilled into the enclosure through openings
17.Damage Requiring Service - The appliance should be serviced by qualied service
personnel when:
A. The power-supply cord of the plug has been damaged;or
B. Objects have fallen, or liquid has been spilled into the appliance;or
C. The appliance has been exposed to rain, or
D. The appliance does not appear to operate normally or exhibits a marked change inperformance, or
E. The appliance has been dropped, or the enclosure damaged.
18.Servicing - The user should not attempt to service the appliance beyond that described
in the operating instructions. All other servicing should be referred to qualied service personnel.
SPEAKER VOLUME
ON/OFF
KNOB
EARPHONE JACK
RADIO\
SD/USB\
PHONO
SWITCH
SD CARD
DIAL SCALE AM\FM\
FM.ST
SWITCH
USB PORT
TUNING KNOB SPEAKER
X-BASS
ON/OFF
BACKWARD SKIP
FORWARD SKIP
REC/ERASE
POWER
INDICATOR
SENSOR
LCD DISPLAY
FM.ST INDICATOR
PROGRAM
STOP/
SD/USB
PLAY/
PAUSEREPEAT
EXTERNAL
FM ANTENNA
LINE OUT
JACK
LINE IN JACK
LINE IN SWITCH
AC POWER PLUG
LOCATION OF PARTS
LOCATION OF PARTS
SPINDLE TURNTABLE
ADAPTER FOR 45 RPM RECORDS
TONE ARM
TONE
ARM
REST
SPEED CONTROL SWITCH
PLAY/PAUSE
STOP/SD/USB
BACKWARD SKIP
0-9
REC/ERASE
REPEAT
FORWARD SKIP
PROGRAM
PROG
79
8
3
12
45 6
0
REPEAT
REC/
ERASE
SD/USB
Unpacking
1 packing materials from unit.
Note: Save all packing materials.
2 Remove plastic bag covering radio.
3 Remove tie from A/C cord and untie antenna wire on back of radio.
4 Open lid and remove styrofoam shipping material from turntable.
5 Remove black tie-wrap from under the tone arm.
6 Remove white protective needle cover by gently pulling towards the front of the unit.
Remarks:
a) ESD remark: In case of malfunction due to electrostatic discharge, just reset the product
(reconnect of power source may be required) to resume normal operation.
b) Electrical Fast Transient (Burst) Remark (I2): In case of malfunction due to electrical fast transient
(Burst), just reset the product. (reconnect of power source may be required) to resume normal
operation.
SETUP
1. Unwind the AC POWER CORD at the back of unit.
2. Untie the FM antenna and allow it to hang down in a straight line for optimum FM reception. If you
have trouble tuning a FM station, move the external FM antenna for best reception. Do not connect
FM antenna to outside antenna.
Power Source
1. Plug the A/C cord into appropriate outlet.
Radio Operation
1. Set the Function switch to RADIO.
2. Switch the unit ON by turning the VOLUME knob to the on Position.
3. Turn the VOLUME control in mid-range position.
4. Slide the Band switch to the desired band (AM or FM or FM.ST).
5. Select the desired radio station by rotating Tuning Knob
6. Adjust the Volume Knob to the desired sound level.
Antenna
Antenna: for FM reception, the unit is provided with a FM WIRE ANTENNA, move the wire until the
reception is clear and with no interferences. For AM reception, the unit is provided with a directional
build-in ferrite antenna. Rotate the set to nd the position in which the best reception is obtained.
Do not connect the EXTERNAL FM ANTENNA to any outside antenna.
USB & SD-CARD OPERATION
SD-Card operation:
1. Slide THE FUNCTION Switch to SD/USB mode.
2. Switch the unit ON by turning the VOLUME knob to the on Position. If no Card has been detected,
”Read”*’3f”No Card” will be show on the display.
CARD CARD
3. Turn the VOLUME control in mid-range position.
4. Insert SD-Card into the card slot. “READ” is displayed as the system scans the contents of SD
card.
5. Track no. 1 of root folder (Folder 1) will be displayed after reading SD card contents.
Press PLAY/PAUSE / to start music.
6. Press the FORWARD SKIP / / BACKWARD SKIP / once or repeatedly until the desired
track number appears on the display. Release the button – the track will start playing automatically.
7. Press STOP / to stop playback.
8. To pause the music, press PLAY/PAUSE / , press it again to resume play.
USB operation:
1. Slide the FUNCTION Switch to SD/USB mode.
2. Switch the unit ON by turning the VOLUME knob to the on Position.
3. Turn the VOLUME control in mid-range position.
4. In stop mode Press STOP / and hold key over 2 seconds will switch SD->USB.
If no USB has been detected, “ NO USB” will show on the Display.
USB
5. Plug-in USB mass storage device. READ is displayed as the system scans the contents of USB
device.
USB
6. Track no. 1 of root folder (Folder 1) will be displayed after reading USB device contents.
Press PLAY/PAUSE / to start music.
USB
MP3
7. Press the FORWARD SKIP / / BACKWARD SKIP / once or repeatedly until the
desired track number appears on the display. Release the button – the track will start playing
automatically.
8. Press STOP / to stop playback.
9. To pause the music, press PLAY/PAUSE / , press it again to resume play.
Remarks:
1. USB connector does not support connection with USB extension cable is not designed for
communication with computer directly.
2. It is not guarantee that all USB memory devices and SD cards will work on this audio system
IMPORTANT:
Do not disconnect the USB device SD card during USB/SD card mode, as this may damage
the external device or its les. Please power off rst or press another Mode before safely
disconnecting the USB device /SD card.
USB Specication:
Interface
- USB 2.0 Full speed, HOST (USB HUB is not supported) Corresponding Flash memory
- Compatible with MPEG Audio 1, 2, 2.5
- Compatible with Layer 1, 2, 3
- Compatible with Bit rate: 128 – 320 Kbps
- Subfolder nest : 8 levels
- Number of track / titles max 999
- Support ID3 tag V2.0
TURNTABLE
PREPARING TO USE THE TURNTABLE
1. Lift up lid and remove black tie-wrap by untwisting and gently sliding out from TONE ARM
2. Remove cardboard shipper.
3. Remove white protective needle cover by gently pulling towards front of unit.
4. Release TONE ARM and hold-down clip by gently pushing to the right.
This will unlock tone arm from its ARM REST. Re-lock the hold-down clip when moving the unit
to another location.
TURNTABLE OPERATION
1. Slide the FUNCTION Switch to PHONO mode.
2. Switch the unit ON by turning the POWER switch to the on Position.
3. Turn the VOLUME control in mid-range position.
4. Set the SPEED CONTROL SWITCH to the correct speed (33 1/3, 45 or 78 rpm) for the selected
record.
5. Move the tone arm over the record and lower it to the point you want the record to start.
6. At the end of the record, the TONE ARM will stop automatically. You must return it to the TONE
ARM REST by hand.
ACCESSORY SUPPLIED :
Adaptor for 45 rpm records
To play a 45 rpm record, remove the adaptor by placing thumb &
forenger in recesses and pulling it upwards.
Then placing it on the SPINDLE. The record can then be placed on the turntable.
PROGRAMMING TRACKS
You may store up to 20 tracks in the desired sequence.
1. In the stop position, press PROGRAM / to start programming. Icon “P” and P0-01 start ashing.
CD
P
2. Press the FORWARD SKIP/ / BACKWARD SKIP/ once or repeatedly until the desired track
number appears in the display.
3. Press PROGRAM / to conrm, display shown stored track no. and next store position.
CD
P
4. Repeat step 2-3 to select and store all desired tracks. FULL is displayed if you attempt to program
more than 20 tracks
PCD
5. Press PLAY/PAUSE/ to play the program.
Erasing the programme
You can erase the contents of the memory by :
- once if in stop position, twice during playback
- Press POWER
- Select another sound source
Play mode
1. Press REPEAT / on remote at Play mode.
2. Default Play Mode function is OFF.
3. REPEAT 1 / REPEAT FOLDER / REPEAT ALL . THREE kinds of Play Mode can be chosen in
MP3 type.
X-BASS
Press the X-BASS ON/OFF to ON or OFF the X-BASS effect(Adjust the volume level to mid to maxi-
mize the X-BASS effect).
Line Out Outputs
1. You can connect this unit to different sources using the auxiliary output jacks.
2. Connect the auxiliary cables (not supplied) to the LINE OUT JACK and to the auxiliary inputs of the
desired component. See the owner’s manual for the operating instructions for the desired
component. The LINE OUT JACK only output a signal and will not run external speakers without
using a separate amplied source.
Auxiliary Input
1 You can connect external components to your unit by using the Auxiliary Input.
2 Plug Auxiliary cable into the LINE IN JACK on the back of your unit.
3 Switch the LINE IN SWITCH to the ON position.
4 Plug the other end of the Auxililary cable into the output jack on your desired external component.
5 Check the volume level of your external component.
6 See operators manual for correct operation of the external component.
NOTE: When not using the Auxiliary Input, make sure the LINE IN SWITCH is in the OFF position.
MP3 copying
1. In USB or SD card playback, Press REC/ERASE/ to start Mp3 copying from USB to SD card or
SD card to USB.Playback will be stopped and system will scan the contents of USB/SD card and
create folder to store MP3 track.
2. icon “ REC “ displayed
3. Message COPY will be displayed.
4. The target device icon “USB” or “CARD” start ashing, MP3 copying start, the process will stop as
copy nished.
5. Current MP3 will be playback from beginning
6. You can copy Mp3 from USB to SD card or SD card to USB at Stop Mode press REC/ERASE /
It may not to copy all MP3 depending on the MP3 le, USB device and SD card
From Phono to SD / USB
The system is capable of converting audio signal from PHONO input to MP3 format and store in USB
mass storage device or SD card (default USB if both devices are detected)
1. Slide the FUNCTION button to PHONO mode.
2. Press REC/ERASE / to start ripping, the system will scan the contents of USB/SD card and
create folder to store MP3 tracks.
3. Icon “ REC ” and message “ TO” are displayed of about 15 seconds, icon “ USB “ start ashing.
4. The target device icon “ USB ” or “ CARD ” start ashing as REC begins.
5. Press STOP / to exit PHONO Rec
Delete MP3 tracks
The system support deleting previous recorded MP3 or existing les.
1. In USB or SD card playback mode, press and hold REC/ERASE / for 2 seconds, current
playback track is stopped and will be deleted.
2. Message “ delete “ is displayed
Auxiliary Output
1 You can connect your radio to different sources using the auxiliary output.
2 Plug Auxiliary cables (not supplied) into the LINE OUT JACK.
3 Connect the other end of the Auxiliary cables into the input on your desired component.
4 See the owners’ manual for the component for correction operation.
NOTE: The Auxiliary Output is a passive signal level output only and will not power speakers.
Auxiliary Input
1 You can connect external components to your unit by using the Auxiliary Input.
2 Plug Auxiliary cable into the LINE IN JACK on the back of your unit.
3 Set the FUNCTION SWITCH to LINE IN mode
4 Plug the other end of the Auxiliary cable into the output jack on your desired external componet
5 Check the volume level of your external component.
6 See operator’s manual for correct operation of the external component.
Table des matières
Langues :
Autres manuels Ricatech Platine
Ricatech
Ricatech RMC240 Manuel utilisateur
Ricatech
Ricatech RTT98 Manuel utilisateur
Ricatech
Ricatech Ibiza RMC90 Manuel utilisateur
Ricatech
Ricatech RTT77 Manuel utilisateur
Ricatech
Ricatech RMC430 Manuel utilisateur
Ricatech
Ricatech REVOLUTION BLACK RTT20 Manuel utilisateur
Ricatech
Ricatech RTT21 Manuel utilisateur
Ricatech
Ricatech RMC250 Deluxe Manuel utilisateur
Ricatech
Ricatech RTT95 Manuel utilisateur
Ricatech
Ricatech RTT22 Manuel utilisateur
