Renkforce FDM 3D Printer Pro 6+ Manuel utilisateur

Insert the print bed and magnetic mat.

Remove the styrofoam pads

1. Install the spool holder.

2. Slide the lament spool onto the holder.

1. Insert the lament tube in the feeder.

2. Insert the lament tube into the extruder.

System

Tool Print

1. Connect the mains cable to the power inlet on the printer.

2. Flip the power switch into the position I to switch on. The display lights up.

Quick Start Guide

FDM 3D Printer Pro 6+

Item No. 2583518

Read the safety instructions supplied

with the product before using

1Set printer up 2Calibrate Z-Offset

Insert the print bed and magnetic mat.

Open the menu Tools.Touch the button Preheating to start the pre-

heating process.

Wait until the preheat temperature has been reached.

Open the menu Manual.Touch to move the extruder to its zero posi-

tion.

Activate the Z-offset calibration with the slider. Touch the distance increment 0.1 mm to

activate it.

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights including translation reserved.

Reproduction by any method, e.g. photocopy, microlming, or the capture in electronic data processing systems require the prior written approval

by the editor. Reprinting, also in part, is prohibited. This publication represents the technical status at the time of printing.

3Load lament

Open the menu Tools.Open the menu Filament.

Touch the temperature display to preheat the

extruder.

Cut the lament at an angle and then feed it into

the feeder.

Touch the button E1 Load to load the lament

into the extruder.

Touch the button Stop as soon as molten lament ows from the nozzle.

4Print

CAUTION

Hot print bed

Touching hot print bed can cause burns

Let cool down before touching

System

Tool Print

Connect the USB memory stick that contains

the print le to the USB port.

Open the menu Print.

Body-Mido.gcode

mm/s

16%

191/190

51/50 100mm/s

04h07m 03h06m

K1-07-11.gcode

Select le to print. The printer starts printing.

5 6

After printing is complete, let the printer cool

down to room temperature.

Remove the magnetic mat.

Slide one sheet of A4 paper (80 g) between the

nozzle and the print bed.

Slide the paper back and forth while repeatedly touching the button or to lift or lower the

print bed. If you notice slight resistance between nozzle, paper, and print bed, touch the button

to nish the calibration.

Conrm the Z-offset calibration. Touch the button Leveling to start

“Auto-levelling”.

Wait for “Auto-levelling” to nish.

Autres manuels pour FDM 3D Printer Pro 6+

Ce manuel convient aux modèles suivants

Autres manuels Renkforce Imprimante 3D

Renkforce

Renkforce 1528625 Manuel utilisateur

Renkforce

Renkforce 1522157 Mode d’emploi

Renkforce

Renkforce 1538778 Mode d’emploi

Renkforce

Renkforce Basic 3 Manuel utilisateur

Renkforce

Renkforce RF100 Guide de configuration

Renkforce

Renkforce FDM 3D Printer Pro 6+ Manuel utilisateur

Renkforce

Renkforce 2584537 Mise à jour du firmware

Renkforce

Renkforce RF100 XL Manuel d'utilisation

Renkforce

Renkforce 2583518 Manuel d'utilisation

Renkforce

Renkforce RF500 Maker Construction Kit Manuel utilisateur

Renkforce

Renkforce 1521716 Mode d’emploi

Renkforce

Renkforce Pro 6 Manuel utilisateur

Renkforce

Renkforce RF1000 Manuel utilisateur

Renkforce

Renkforce RF100 Manuel utilisateur

Renkforce

Renkforce RF2000 v2 Series Manuel utilisateur

Renkforce

Renkforce RF100 Manuel utilisateur

Renkforce

Renkforce RF2000 Manuel utilisateur

Renkforce

Renkforce RF100 XL Manuel utilisateur

Renkforce

Renkforce RF Pro 3 Manuel utilisateur

Renkforce

Renkforce FDM 3D Printer Pro 6+ Manuel utilisateur

Renkforce

Renkforce 3D Drucker Cube One Manuel utilisateur

Renkforce

Renkforce RF100 v2 Manuel utilisateur

Manuels Imprimante 3D populaires d'autres marques

Ultimaker

Ultimaker S5 Material Station Manuel utilisateur

EcubMaker

EcubMaker TOYDIY Manuel utilisateur

AnyCubic

AnyCubic Kossel Plus Manuel utilisateur

ReDeTec

ReDeTec ProtoCycler Manuel utilisateur

Kywoo3D

Kywoo3D Tycoon IDEX Manuel utilisateur

CraftBot

CraftBot PLUS PRO Manuel utilisateur

3DGence

3DGence INDUSTRY F340 Manuel utilisateur

HP Jet Fusion 4200 Mode d'emploi

Rokit

Rokit AEP Series Manuel utilisateur

AnkerMake

AnkerMake M5 Manuel utilisateur

DIYElectronics

DIYElectronics PRUSA I3 Instructions de montage

Ackuretta

Ackuretta FreeShape 120 Manuel utilisateur

LONGER

LONGER LK5Pro Manuel utilisateur

Stratasys

Stratasys J850 Manuel utilisateur

MakerBot

MakerBot Replicator Manuel utilisateur

Stratasys

Stratasys FDM Vantage Series Manuel utilisateur

ZYYX

ZYYX Pro II Manuel utilisateur

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guide de l'utilisateur