Renishaw UCC2 Manuel utilisateur
General information
© 2004 ‐ 2019 Renishaw plc. All rights reserved.
This document may not be copied or reproduced in whole or in part, or transferred to any other media or language, by any means, without
the prior written permission of Renishaw.
The publication of material within this document does not imply freedom from the patent rights of Renishaw plc.
Disclaimer
RENISHAW HAS MADE CONSIDERABLE EFFORTS TO ENSURE THE CONTENT OF THIS DOCUMENT IS CORRECT AT THE DATE OF
PUBLICATION BUT MAKES NO WARRANTIES OR REPRESENTATIONS REGARDING THE CONTENT. RENISHAW EXCLUDES LIABILITY,
HOWSOEVER ARISING, FOR ANY INACCURACIES IN THIS DOCUMENT..
Trademarks
RENISHAW® and the probe emblem used in the RENISHAW logo are registered trademarks of Renishaw plc in the UK and other countries.
apply innovation is a trademark of Renishaw plc.
All brand names and product names used in this document are trade names, service marks, trademarks, or registered trademarks of their
respective owners.
All trademarks and trade names are acknowledged.
WEEE
The use of this symbol on Renishaw products and/or accompanying documentation indicates that the product should not be mixed with the
general household waste upon disposal. It is the responsibility of the end user to dispose of this product at a designated collection point for
waste electrical and electronic equipment (WEEE) to enable reuse or recycling. Correct disposal of this product will help save valuable
resources and prevent potential negative effects on the environment. For more information, please contact your local waste disposal service
or Renishaw distributor.
Warranty
Renishaw plc warrants its equipment for a limited period (as set out in our Standard Terms and Conditions of Sale) provided that it is installed
exactly as defined in associated Renishaw documentation.
Prior consent must be obtained from Renishaw if non-Renishaw equipment (e.g. interfaces and/or cabling) is to be used or substituted. Failure
to comply with this will invalidate the Renishaw warranty.
Claims under warranty must be made from authorised service centres only, which may be advised by the supplier or distributor.
UCC2 and UCC2-2 installation guide
www.renishaw.com
Issued 07 2021
2
Care of equipment
Renishaw probes and associated systems are precision tools used for obtaining precise measurements and must therefore be treated with
care.
Changes to Renishaw products
Renishaw reserves the right to improve, change or modify its hardware or software without incurring any obligations to make changes to
Renishaw equipment previously sold.
Packaging
To aid end user recycling and disposal the materials used in the different components of the packaging are stated here:
Packaging component Material 94/62/EC code 94/62/EC number
Outer box Corrugated fibreboard PAP 20
Packaging insert Corrugated fibreboard PAP 20
Plastic bags Low density polyethylene bag LDPE 4
Padded bag Paper PAP 21
UCC2 and UCC2-2 installation guide
www.renishaw.com
Issued 07 2021
3
Product compliance
EU declaration of conformity
Contact Renishaw plc or visit www.renishaw.com/EU for the full EU declaration.
FCC (USA only)
Information to user (47 CFR 15.105)
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These
limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference, in which case you will be required to correct the interference at your own expense.
Information to user (47 CFR 15.21)
The user is cautioned that any changes or modifications not expressly approved by Renishaw plc or authorised representative could void the
user's authority to operate the equipment.
Equipment label (47 CFR 15.19)
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
REACH regulation
Information required by Article 33﴾1﴿ of Regulation ﴾EC﴿ No. 1907/2006 ﴾“REACH”﴿ relating to products containing substances of very high
concern (SVHCs) is available at:
www.renishaw.com/REACH
China RoHS
Contact Renishaw plc or visit www.renishaw.com/ChinaRoHS for the full China RoHS tabulation.
UCC2 and UCC2-2 installation guide
www.renishaw.com
Issued 07 2021
4
Safety
Electrical requirements
The UCC2 and UCC2-2 is powered from the ac mains supply via an IEC 320 connector. The operating voltages of the unit are as follows:
100 Vac ‐ 120 Vac and 220 Vac ‐ 240 Vac –
15%, +10%
50 Hz / 60 Hz ±5% 120 W maximum
This equipment must be connected to a protective earth conductor via a three core mains (line) cable. The mains plug shall be inserted only
into a socket outlet provided with a protective earth contact. Connect the unit to mains power using a suitably rated cord and plug conforming
to local regulations. The cord and plug must be capable of carrying 264 Vac / 3 A. Do not use an extension cable without a protective
conductor.
An earth stud is provided to allow bonding of the CMM's metal parts to the protective earth.
CAUTION: Any interruption of the protective conductor may make the equipment dangerous. Make sure that the grounding
requirements are strictly observed.
Machine safety
WARNING: Switching off or isolating the UCC2 and UCC2-2 may NOT prevent unexpected machine movement. The user is
advised to Isolate the machine from the electricity supply, compressed air or other energy sources in accordance with the machine
manufacturer's instructions before entering the danger zone or performing any maintenance operations.
If the equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired.
UCC2 and UCC2-2 installation guide
www.renishaw.com
Issued 07 2021
6
Environmental conditions
The following environmental conditions comply with (or exceed) BS EN 61010-1:1993:
Indoor use IP30 (no protection against water)
Altitude Up to 2000 m
Operating temperature 0 °C to +50 °C
Storage temperature ‐10 °C to +70 °C
Relative humidity 80% maximum ﴾non‐condensing﴿ for temperatures up to +31 °C
Linear decrease to 50% at +40 °C
Transient overvoltages Installation category II
Pollution degree 2
NOTE: If a higher IP rating is required, an additional external enclosure will be required to house the UCC2 and UCC2-2. This
enclosure must facilitate an airflow to allow the internal temperature to maintain the ambient within the operating temperature
range.
UCC2 and UCC2-2 installation guide
www.renishaw.com
Issued 07 2021
7
References and associated documents
It is recommended that the following documentation is referenced when installing the UCC2 and UCC2-2:
Renishaw documents
Title Document number
H-1000-5172 MCU1 installation guide
H-1000-5220 UCC daughtercard installation guide
H-1000-5247 SPA2-2 installation guide
H-1000-5107 SPAlite user's guide
External documents
National and international standards including the following may be applicable to the finished machine or installation: -
EN 292-2:1991 (Safety of machinery - Basic concepts, general principles for design - Part 2: Technical principles and specifications.
EN (IEC) 60204-1:1997 (Safety of machinery - Electrical equipment of machines - Part 1: General requirements).
UCC2 and UCC2-2 installation guide
www.renishaw.com
Issued 07 2021
8
Specifications
Physical specification
The UCC2 controller is housed inside a 3U high enclosure which can be mounted in a 19 inch rack. Alternatively, it can be used as a desktop
unit.
A rack mounting kit (Renishaw part number A-5121-0006) is available as an optional extra.
Height: 127 mm
Depth: 330 mm
Width: 435 mm
Weight: 8 kg (without cables and daughtercards)
Cable lengths
UCC2 to CMM measuring scale readhead
The maximum specified cable length is 18 metres assuming that individual cable wire cross‐sectional area is a minimum of 0.055 mm². For
further details please refer to "CMM readhead input connections".
UCC2 to CMM servo power amplifier input
Dependent on the servo power amplifier, SPAlite, SPA1 or SPA2-2, this link is either a dedicated 25-way D-type cable or a pair of ethernet
cables. One metre cables are supplied as standard with the SPA kits. Other lengths can be fitted but it is recommended that the cable is kept as
short as possible with a maximum cable length of 2 metres.
Ethernet cable link to PC
This is a standard ethernet cat 5 cross-over cable and a 5 metres cable is supplied as part of the UCC2 kit.
Other lengths can be fitted up to a maximum of 100 metres.
Scale readhead signal speed
The maximum frequency of any one of the scale readhead quadrature signals, with ideal waveforms and phase displacement, is 12.5 MHz.
However, it is recommended that the maximum frequency of any one of the scale readheads should be 10 MHz.
UCC2 and UCC2-2 installation guide
www.renishaw.com
Issued 07 2021
9
Electrical power requirements
Controller output supplies
The UCC2 produces a +24 V current limited supply with a maximum output current of 1 A. This supply is available for use by the CMM system
to supply status switches, etc.
The UCC2 also provides protected supplies for other external devices such as scale read-heads, the probe, joystick, etc.
These supplies are:
+ 5 Vdc* at 1 A max
+15 Vdc at 1 A max
- 15 Vdc at 1 A max
* The supply to the scale readheads is a nominal 5.2 Vdc but, providing the sensor lines are connected through to the readhead, this voltage
servoes within the range 5 Vs to 7 Vs to ensure the supply is 5.2 V at the readhead i.e. it compensates for the cable volt drop. If the sensor
lines are not connected the supply defaults to 5.2 Vdc.
UCC2 and UCC2-2 installation guide
www.renishaw.com
Issued 07 2021
10
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Renishaw Instrument de mesure
Renishaw
Renishaw RENGAGE RMP400 Manuel utilisateur
Renishaw
Renishaw RENGAGE OMP600 Manuel utilisateur
Renishaw
Renishaw OTS Manuel utilisateur
Renishaw
Renishaw MIH Manuel utilisateur
Renishaw
Renishaw REVO-2 Manuel utilisateur
Renishaw
Renishaw Equator Gauge Checker Manuel utilisateur
Renishaw
Renishaw SP80 Manuel utilisateur
Renishaw
Renishaw RLP40 Manuel utilisateur
Renishaw
Renishaw RLP40 Manuel utilisateur
Renishaw
Renishaw RMP40 Manuel utilisateur
Renishaw
Renishaw TP8 Manuel utilisateur
Renishaw
Renishaw RMP600 Manuel utilisateur
Renishaw
Renishaw APCA Series Manuel utilisateur
Renishaw
Renishaw PH10 PLUS Series Manuel utilisateur
Renishaw
Renishaw NC1 Mode d'emploi
Renishaw
Renishaw XK10 Manuel utilisateur
Renishaw
Renishaw OMP40 Manuel utilisateur
Renishaw
Renishaw RP1 Manuel utilisateur
Renishaw
Renishaw LP2 Manuel utilisateur
Renishaw
Renishaw RMP600 Manuel utilisateur
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
Keysight
Keysight M8290A Manuel utilisateur
ADTEK
ADTEK MW-5 Manuel utilisateur