Renesas RH850/E2 Series Manuel utilisateur

RH850 Evaluation Platform

RH850/E2x-

292BGA

PiggyBack board

Y-RH850-E2X-292PIN-PB-T1-V1

R20UT4084ED0130 Rev. 1.3

2020-05-12

All information contained in these materials, including products and product specifications,

represents information on the product at the time of publication and is subject to change by

Renesas Electronics Corp. without notice. Please review the latest information published by

Renesas Electronics Corp. through various means, including the Renesas Technology Corp.

website (http://www.renesas.com).

The newest version of this document can be obtained from the following web location:

http://www.renesas.eu/updates?oc=Y-RH850-E2X-292PIN-PB-T1-V1#documentInfo

www.renesas.com

User Manual

R20UT4084ED0130 Rev. 1.3

2020-05-12

Table of Contents

Chapter 1 Introduction ......................................................................... 3

Chapter 2 Overview .............................................................................. 4

2.1 Overview of Y-RH850-E2X-292PIN-PB-T1-V1 .....................................4

2.2 Mounting of the device ........................................................................5

Chapter 3 Power supply ....................................................................... 6

3.1 Board power connection .....................................................................6

3.2 Voltage distribution..............................................................................7

Chapter 4 Clock sources...................................................................... 9

4.1.1 MainOsc .........................................................................................................................9

4.1.2 Programmable Oscillator .............................................................................................9

Chapter 5 Debug and Programming interface .................................. 10

5.1 14 Pin Debug Connector....................................................................10

5.2 34 Pin Aurora Connector ...................................................................10

Chapter 6 Connectors for ports of device......................................... 12

6.1 Push button for RESET......................................................................12

6.2 Mode Selection ...................................................................................12

6.3 Connectors to MainBoard..................................................................12

6.3.1 Assignment of CAN Pins ...........................................................................................12

6.4 RHSIF I/F .............................................................................................13

6.5 HS-SPI I/F ............................................................................................13

6.6 RHSB I/F ..............................................................................................14

Chapter 7 Other circuitry.................................................................... 15

7.1 Signalling for ERROROUT_M ............................................................15

7.2 Pin Headers for Pull-Down and Pull-Up............................................15

7.3 Signalling LEDs ..................................................................................15

Chapter 8 Jumper Configuration ....................................................... 16

Precautions........................................................................ 18

Chapter 9

9.1

9.2

Power-Off Sequence ..........................................................................18

Changed Pin Number on Jumper JP18 ........................................... 18

Chapter 10 Mechanical dimensions .................................................... 19

Chapter 11 Schematic .......................................................................... 20

Chapter 12 Revision History ................................................................ 26

R20UT4084ED0130 Rev. 1.3

2020-05-12

Chapter 1 Introduction

The RH850/E2x Application Board is part of the RH850 Evaluation Platform and

serves as a simple and easy to use platform for evaluating the features and

performance of Renesas Electronics 32-bit RH850/E2x microcontrollers in a

BGA-292 package. The PiggyBack board (Y-RH850-E2X-292PIN-PB-T1 -V1)

can be used as a standalone board, or can be mated with a mainboard (Y-

RH850-X1X-MB-Tx-Vx) for extended functionality.

Main features:

Socket for mounting of device

Standalone operation of the board

Direct supply of device voltage (typ. 5V, 3.3V and 1.25V) enabling single

power supply and dual power supply

Device programming capability

Device debugging capability

Pin headers for direct access to each functional device pin

Reset switch

MainOSC circuitry

Connectors to MainBoard

Operating temperature from 0°C to +40°C

This document describes the functionality provided by the PiggyBack board and

guides the user through its operation.

For details regarding the operation of the microcontroller, refer to the

corresponding User’s Manual.

R20UT4084ED0130 Rev. 1.3

2020-05-12

Chapter 2 Overview

2.1 Overview of Y-RH850-E2X-292PIN-PB-T1-V1

Figures 1 and 2 provide a schematic view of the Y-RH850-E2X-292PIN-PB-T1-

V1 PiggyBack board.

Figure 1 PiggyBack Board Top View

The red arrow denotes the position of socket pin #1.

Figure 2 PiggyBack Board Bottom View

RH850-E2X-292PIN-PB-T1-V1

EESS-0401-153-02

R20UT4084ED0130 Rev. 1.3

2020-05-12

2.2 Mounting of the device

The Y-RH850-E2X-292PIN-PB-T1-V1 PiggyBack board features a socket for

mounting of the device. All E2x in BGA-292 package do fit into the available

Enplas OTB-292(961RS)-0.8-019S-00 socket.

The device must be placed inside the socket IC1. To insert the device align the

device package #1pin with the #1pin of the socket. The #1pin of the socket is

marked with a circle near to the “IC1” label (see also red arrow in Figure 1). The

#1pin of the device is marked by a white triangle on the package (see white circle

in Figure 3).

Figure 3 Enplas OTB-292(961RS)-0.8-019S-00 Socket with Mounted Device

CAUTION: Please be careful with the placement to not damage the device.

R20UT4084ED0130 Rev. 1.3

2020-05-12

Chapter 3 Power supply

3.1 Board power connection

For operation of the device, a supply voltage must be connected to the board.

There are several possibilities to power the device.

Within this document, the following voltages are considered as ‘typical’ values:

Voltage1 = 5V

Voltage2 = 3.3V

Voltage3 = 1.25V

Direct voltage supply

Three different voltages can be supplied to the board.

The following connectors are available to supply those voltages directly:

Four 4mm ‘banana-type’ connectors:

- Three red connectors for voltages 5V (CN15), 3.3V (CN23) and 1.25V

(CN24).

- A black connector for ground (GND) connection (CN22).

Note: The four connectors are supplied with the board but not assembled.

For details about voltage distribution, refer to Chapter 3.2 ‘Voltage distribution’.

Supply by MainBoard

In case the PiggyBack board is mounted on a MainBoard, the 5V and 3.3V is

supplied by the on-board regulator of the MainBoard.

CAUTION: Do not supply 5V or 3.3V directly to the PiggyBack board in case it is

mounted on the MainBoard.

For each of the voltages, 5V, 3.3V and 1.25V a green LED (LED3, LED2 and

LED5, respectively) is available to signal that the related voltage is available on

the PiggyBack board. The corresponding LEDs are placed directly beneath the

connectors of the related voltage.

R20UT4084ED0130 Rev. 1.3

2020-05-12

3.2 Voltage distribution

The table shows the required device power supply pins. For detailed explanation

of their function and specification, please refer to the user documentation of the

corresponding device:

Table 1 Available Power Domains for MCU

Device Supply Pin

SYSVCC

VCC

EnVCC (n = 0-2)

LVDVCC

EMUVCC

AnVCC (n = 0 and 2)

AnVREFH (n = 0 and 2)

ADSVCC

ADSVREFH

EMUVDD

VDD

Additional power supply for the MainBoard and the operation of the PiggyBack

board can be selected:

Table 2 Available Power Domains for Board Operation

Supply voltage

Function

VDDIOF

IO supply voltage for components located on a

connected mainboard.

Board_VCC

Source for all devices (e.g. voltage regulator) on the

PiggyBack board

The following figure shows the configurable voltage distribution on the PiggyBack

board.

All power supply lines can be interrupted by jumpers. This provides the

possibility to measure the current consumption of each individual power

domain of the device (JP4 –16 and JP23 –24).

The IO supply voltage for the Mainboard (VDDIOF) can be connected via

jumper JP17 to 5V or 3.3V, if the PiggyBack board is mounted on a

MainBoard.

VDD and EMUVDD can be powered either directly from the ‘banana-type’

connector (CN24) or by an on-board voltage regulator.

The source for the on-board voltage regulator, as well as the source for all

on-board devices (Board_VCC) needs to be configured via jumper JP30 to

either 5V or 3.3V.

The source for VDD is selectable by the jumper JP22. The jumper JP23 and

JP24 connect the voltage, configured by JP22 with the VDD and EMUVDD

pins.

R20UT4084ED0130 Rev. 1.3

2020-05-12

Note: Although nominally 1.25V is used even as name in the schematic the

output of the voltage regulator IC19 is slightly increased to 1.28V (see

Chapter 11 ‘Schematic’). With this sufficient high voltage is applied, even in

case of any possible voltage drops.

Figure 4 Voltage Distribution on the PiggyBack Board

•The voltage supplied to the device pin W3 (marked "Ball_W3") must be

configured to either LVDVCC or E0VCC according to the device pinout.

Please check the device HW user’s documentation for more details.

For more details, please refer to Chapter 11 ‘Schematic’. For typical

configuration of the jumpers, please refer to Chapter 8 ‘Jumper Configuration’.

JP0+5V

JP1+3.3V JP4

JP2

JP3

E0VCC

JP5

E1VCC

E2VCC

VDDIOF (to

mainboard)

JP6

JP17

JP7

LVDVCC

SYSVCC

VCC

EMUVC C

JP8

JP9

JP10

JP11

A0VCC

JP12

A0VREFH

A2VCC

A2VREFH

ADSVCC

ADSVREFH

JP13

JP14

JP15

JP16

+5V

+3.3V

+1.25V

Voltage regulator IC

fo r 1.25V

Board_VCC

#1 #2

#3 #2 #1

#1 #2

#3 #2 #1

JP22

#3 #2 #1

VDDJP23

#1 #2

EMUVDDJP24

JP30

#3 #2 #1

E0VCC

LVDVCC

JP18

Ball_W3

R20UT4084ED0130 Rev. 1.3

2020-05-12

Chapter 4 Clock sources

External crystal oscillators for the device clock supply are provided with the

board.

4.1.1 MainOsc

A crystal or ceramic resonator can be mounted on socket X1.

A 20MHz and a 40MHz oscillator are supplied with the board.

The signals X1 and X2 are by default not connected to a pin header in order to

minimize disturbance on the resonator signal. If needed the signals can be

connected to CN5 (pins #24 and 26) via connecting with 0Ohm resistances R48

and R49. For details, please refer to Chapter 11 ‘Schematic’.

4.1.2 Programmable Oscillator

It is possible to mount a programmable crystal oscillator on the PiggyBack board

at OSC1. The available footprint and circuitry is designed for a SG-8002CE

programmable crystal oscillator from Epson Toyocom. The output from this

oscillator can be connected to port X1 via resistor R38. The SG-8002CE is

neither mounted nor provided with the board. For details about the available

circuitry, refer to Chapter 11 ‘Schematic’. A resonator mounted on socket X1

must not be used in parallel to another clock source.

R20UT4084ED0130 Rev. 1.3

2020-05-12

Chapter 5 Debug and Programming interface

The signal ‘EVTO’ from below connectors can be pulled up to ‘E0VCC’ via JP28.

Please refer to the documentation of the used tool, whether this is needed.

The signal ‘TRST’ from below connectors can be pulled up to ‘SYSVCC’ or to the

‘TRST’ line of the used tool via jumper JP31.

For typical configuration of the jumpers, please refer to Chapter 8 ‘Jumper

Configuration’.

5.1 14 Pin Debug Connector

For connection of the microcontroller to debug and flash programming tools, the

connector CN25 with fourteen pins is available.

The signal connection of the connector CN25 is shown in the table below:

Table 3 Pin Assignment of CN25

CN25 Pin

Function

TCK

GND

JP31 #3

MD0

TDO

TDI

VCC

TMS

EVTO (P33_9)

DRDY

GND

RES_IN

GND

5.2 34 Pin Aurora Connector

For connection of the microcontroller to a trace tool CN10 is available.

The signal connection of the connector CN10 is shown in the table below:

Table 4 Pin Assignment of CN10

CN10

Function

CN10

Function

TODP0

VCC

TODN0

TCK

Table des matières

Autres manuels Renesas Microcontrôleur

Renesas

Renesas M16C-Flasher Manuel utilisateur

Renesas

Renesas S3A1 Manuel utilisateur

Renesas

Renesas rl78/g1g Manuel utilisateur

Renesas

Renesas RX65N Series Manuel utilisateur

Renesas

Renesas RL78/G23-128p Manuel utilisateur

Renesas

Renesas V850ES/JE3-L Manuel utilisateur

Renesas

Renesas RH850 Series Instructions d'installation et d'utilisation

Renesas

Renesas V853 Manuel utilisateur

Renesas

Renesas YCONNECT-IT-TPS-1L Manuel utilisateur

Renesas

Renesas R5F51105ADFM Manuel utilisateur

Renesas

Renesas RL78/I1C Manuel utilisateur

Renesas

Renesas RX100 Series Manuel utilisateur

Renesas

Renesas RX72M Renesas Starter Kit Manuel utilisateur

Renesas

Renesas RA2E2 Series Manuel utilisateur

Renesas

Renesas Synergy S3A3 Manuel utilisateur

Renesas

Renesas RL78/G1A Manuel utilisateur

Renesas

Renesas M32C/8x StarterKit Plus Manuel utilisateur

Renesas

Renesas RA Series Manuel utilisateur

Renesas

Renesas 7542 Manuel utilisateur

Renesas

Renesas Synergy SK-S7G2 Manuel utilisateur

Renesas

Renesas RA6 Series Manuel utilisateur

Renesas

Renesas RL78/G15 Manuel utilisateur

Renesas

Renesas RH850/E1L Instructions d'installation et d'utilisation

Renesas

Renesas RA2 Series Manuel utilisateur

Manuels Microcontrôleur populaires d'autres marques

AMS

AMS AS7261 Demo Kit Manuel utilisateur

Novatek

Novatek NT6861 Manuel utilisateur

Espressif Systems

Espressif Systems ESP8266 SDK Guide de configuration

Nuvoton

Nuvoton ISD61S00 ChipCorder Mode d’emploi

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Manuel utilisateur

Texas Instruments

Texas Instruments Chipcon CC2420DK Manuel utilisateur

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Manuel utilisateur

NEC

NEC 78GK0S/K 1+ Series Instructions d'installation et d'utilisation

Mikroe

Mikroe SEMITECH N-PLC Click Instructions d'installation et d'utilisation

Intel

Intel Agilex Manuel utilisateur

Cypress

Cypress CY4607 HX2VL Manuel utilisateur

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Manuel utilisateur

Texas Instruments

Texas Instruments TMS320F2837 D Series Manuel utilisateur

CYPRES

CYPRES CY14NVSRAMKIT-001 Manuel utilisateur

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM Manuel utilisateur

Espressif Systems

Espressif Systems ESP8266EX Mode d'emploi

Abov

Abov AC33M8128L Manuel utilisateur

Laird

Laird BL654PA Manuel utilisateur