Renault Espace Mode d’emploi
77 11 205 204 MAY 1999 Edition Anglaise
N.T. 3219A
"The repair methods given by the manufacturer in this document are based on the
technical specifications current when it was prepared.
The methods may be modified as a result of changes by the manufacturer in the
production of the various component units and accessories from which his vehicles
are constructed".
All copyrights reserved by Renault.
Copying or translating, in part or in full, of this document or use of the service part
reference numbering system is forbidden without the prior written authority of
Renault.
C Renault 1999
JE0N
ESPACE
FITTED WITH THE F4R ENGINE
For parts not described in this technical note refer to Workshop Repair
Manual M.R. 315.
This note is a supplement to Technical Note 3107A (en-
gine and cooling section) and covers the special fea-
tures of Espace vehicles fitted with automatic trans-
mission.
Contents
Pages
Engine and peripherals
Specifications
Engine repair 10-1
10-6
ENGINE AND PERIPHERALS ASSEMBLY
10
Cooling assembly 19-1
COOLING
19
Transmission
Timing belt 11-1
ENGINE AND PERIPHERALS ASSEMBLY
11
Exploded view
General
Consumables
Parts which must always be changed
Oil
Draining
Filling - Levels
Converter setting point check
Hydraulic distributor
Automatic transmission
(Removal- Refitting)
Differential outlet seal
Converter seal
Multifunction switch
Sensors
Solenoid valves
Line pressure socket
23-1
23-2
23-3
23-3
23-3
23-4
23-5
23-6
23-7
23-10
23-14
23-15
23-16
23-18
23-19
23-20
AUTOMATIC TRANSMISSION
23
ENGINE AND PERIPHERALS ASSEMBLY
Specifications 10
Engine Index Cubic capacity
(cm3)Bore
(mm) Stroke
(mm) Compression
ratio
F4R 700
701 1998 82.7 93 9.8/1
10-1
ENGINE AND PERIPHERALS ASSEMBLY
Specifications 10
CYLINDER HEAD
Removal of the cylinder head requires the removal/refitting of the engine and transmission assembly (see
Section 10-2 NT 3107A)
The bolts can be reused if the length under the head does not exceed 118.5 mm (otherwise change all the
bolts).
Cylinder head tightening procedure
REMINDER: to achieve correct tightening of the bolts, remove any oil from the cylinder head securing holes
using a syringe.
Do not coat new bolts with oil. However, if the bolts are reused, it is essential to coat them with engine oil.
Tighten all the bolts to 2 daN.m in the order indicated below.
15153-1R
Check that all the bolts are correctly tightened to 2 daN.m, then carry out angular tightening (bolt by bolt) of
165°±6°.
No retightening of the cylinder head bolts following application of this procedure.
10-2
ENGINE AND PERIPHERALS ASSEMBLY
Specifications 10
15156R
Details of mark (A) :
- mark (B) is only used by the supplier,
- mark (C) identifies the camshafts:
A= Inlet
E= Exhaust
- mark (D) indicates the engine type
Example:
F4RE66810414 22
BCD
VALVES
Valve lift (in mm)
Inlet: 10
Exhaust: 10
Camshafts
The camshafts are identified
- either by a mark (A).
- or by the ends of the camshafts.
15152R
-F exhaust camshaft
-G inlet camshaft
10-3
ENGINE AND PERIPHERALS ASSEMBLY
Specifications 10
Timing diagram (cannot be checked)
Diagram with the intake not dephased
Inlet
camshaft
Cam
1Cam
2
Exhaust
camshaft
Cam
1Cam
2
Intake
opening
delay* - 10 - 14 - -
Intake
closing
delay 40 44 - -
Exhaust
opening
advance --2420
Exhaust
closing
advance** ---40
Diagram with the intake dephased
Inlet
camshaft
Cam
1 Cam
2
Exhaust
camshaft
Cam
1 Cam
2
Intake
opening
delay* 62--
Intake
closing
delay* 24 28 - -
Exhaust
opening
advance --2420
Exhaust
closing
advance** ---40
* As the Intake Opening Delay is negative, the
valves open after TDC.
** As the Exhaust Closing Advance is negative,
the valves close before TDC.
15521R
1 The direction of the piston Λengine flywheel
side
2 The piston category (2-3)
3 Only used by the supplier
4 Only used by the supplier
5 Piston line of symmetry
6 Piston pin hole line
7 Offset between the hole of line (6) and the
piston symmetry line (5) is 0.8 mm
8 Identification of the piston in relation to the
engine, marking of the cubic capacity of the
engine (2) corresponds to the F4R engine.
PISTONS
SMP piston
The pin is free in the connecting rod and in the
piston.
Piston marking
10-4
ENGINE AND PERIPHERALS ASSEMBLY
Specifications 10
CONNECTING RODS
Lateral clearance of the big end (in mm)
0.22 to 0.402
Centreline distance between the big end and the
little end (in mm) 144 ±0.035
Big end diameter (in mm) 51.587
Little end diameter (in mm) 23 (without ring)
21 (with ring)
0
- 0.019
10-5
ENGINE AND PERIPHERALS ASSEMBLY
Engine repair 10
Replacement of the control solenoid valve seal
Remove:
- the coil,
- the solenoid valve,
15200S
- the seal.
The seal is refitted using tool Mot. 1513.
Refit in the reverse order to removal.
16016R
10-6
Angular tightening wrench
14 mm hexagonal wrench
TOP AND FRONT OF ENGINE
Timing belt 11
ESSENTIAL SPECIAL TOOLS
Mot. 799-01 Tool for immobilising pinions for
toothed timing belt
Mot. 1054 Top dead centre pin
Mot. 1509 Tool for immobilising camshaft
pulleys
Mot. 1509-01 Accessory for Mot. 1509
Mot. 1512 Tool for fitting the exhaust
camshaft seal
Mot. 1517 Tool for fitting the inlet camshaft
seal
Mot. 1496 Tool for setting camshafts
ESSENTIAL EQUIPMENT
There are two very distinct procedures for setting
the timing.
FIRST PROCEDURE
This is applied in the event of replacement of any
components which require slackening of the ex-
haust camshaft pulley and of the timing inlet
camshaft phase shifter.
During this operation, it is essential to change:
- the exhaust camshaft pulley nut,
- the inlet camshaft phase shifter bolt,
- the phase shifter camshaft seal,
- the phase shifter blanking piece seal.
11-1
Autres manuels pour Espace
3
Table des matières
Autres manuels Renault Automobile
Renault
Renault FLUENCE Z.E. Manuel utilisateur
Renault
Renault GRAND SCENIC Manuel utilisateur
Renault
Renault Trafic Manuel utilisateur
Renault
Renault MEGANE COUPE CABRIOLET Manuel utilisateur
Renault
Renault Kadjar Manuel utilisateur
Renault
Renault 2005 Megane Manuel utilisateur
Renault
Renault GRAND SCENIC Manuel utilisateur
Renault
Renault WIND Manuel utilisateur
Renault
Renault MEGANE Manuel utilisateur
Renault
Renault Duster Manuel utilisateur
Renault
Renault 2009 X79 Manuel utilisateur
Renault
Renault MEGANE E-TECH 100% ELECTRIC 2022 Manuel utilisateur
Renault
Renault Avantime 2002 Manuel utilisateur
Renault
Renault Twingo Clio Mode d'emploi
Renault
Renault Megane Berline Manuel utilisateur
Renault
Renault zoe Manuel utilisateur
Renault
Renault Duster 2007 Manuel utilisateur
Renault
Renault SENIC Manuel utilisateur
Renault
Renault CLIO 2019 Manuel utilisateur
Renault
Renault KWID 2023 Manuel utilisateur
