Quantum Superloader 3 Manuel utilisateur
SuperLoader 3
SuperLoader™ 3
Quick Start Guide
The Quantum®SuperLoader™ 3 is an automated storage and retrieval
device consisting of a tape drive and up to two tape magazines holding up
to eight cartridges each.
For more information, see the Quantum SuperLoader 3 User’s Guide
(PN 81-81317) on the documentation CD provided with your autoloader.
This quick start guide uses the following conventions:
This document explains how to unpack the SuperLoader 3 and install it in a
standard 19-inch rack.
Choosing a Location
The autoloader is designed to fit in a standard 19-inch rack using either the
long or short brackets (depending on the depth of the rack). The autoloader
uses standard rack mounting hardware.
Note: Notes emphasize important information related to the main
topic.
Caution: Cautions indicate potential hazards to equipment and are
included to prevent damage to equipment.
Warning: Warnings indicate potential hazards to personal safety and
are included to prevent injury.
Note: It is recommended that you review this entire document prior to
beginning the installation.
Contents 0
Choosing a Location.......................... 1
Preparing for the Installation........... 2
Providing Necessary Tools ............. 2
Taking ESD Precautions ................. 3
Preparing for Rack Mounting ........ 3
Unpacking the Autoloader................ 4
Checking Accessories ..................... 5
Rack Mounting the Autoloader ........ 6
Autoloader Panel Overviews........... 12
SCSI Bus Requirements ................... 13
General Information..................... 13
Connecting SCSI, SAS, or
Fibre Channel and Power Cables.... 13
Setting the SCSI ID .......................... 16
Preparing the Host and Verifying
the Connection ............................. 16
Operating System Support ............. 17
Autoloader Device Driver............. 17
Tape Drive Device Driver .............. 17
After the Installation....................... 18
2Preparing for the Installation
SuperLoader™ 3 Quick Start Guide
Choose a location that meets the following criteria:
Preparing for the Installation
Before you begin the installation procedure in this section, make the following
preparations as described in this section:
•Providing Necessary Tools
•Taking ESD Precautions
•Preparing for Rack Mounting
Providing Necessary Tools 0Provide the following tools for unpacking and installing the autoloader:
• #2 Phillips screwdriver
• Level
• Antistatic wrist strap
Criteria Description
Rack requirements Standard 19-inch rack
Room temperature 10–35° C (50–95° F)
Power source AC power voltage: 100–127 VAC; 200–240 VAC
Line frequency: 50–60 Hz
Note: Locate the AC outlet near the autoloader. The AC
power cable is the product’s main disconnect device and must
be easily accessible at all times.
Weight 14.1 kg (31 lb.) unloaded
17.2 kg (38 lb.) loaded with 2 magazines, 16 cartridges
Air Quality Minimize sources of particulate contamination. Avoid areas
near frequently used doors and walkways, cooling or exhaust
vents, stacks of supplies that collect dust, printers, and
smoke-filled rooms.
Caution: Excessive dust and debris can damage tapes and
tape drives.
Humidity 20–80% RH (non-condensing)
Clearance Back: Minimum of 43.2 cm (17 in.)
Front: Minimum of 68.6 cm (27 in.)
Sides: Minimum of 5.08 cm (2 in.)
Preparing for the Installation 3
SuperLoader 3
Taking ESD Precautions 0Some components within the autoloader contain static-sensitive parts. To avoid damaging
these parts while performing installation procedures, always observe the following
precautions:
• Ensure that the work area is free from conditions that could cause electrostatic
discharge (ESD).
• Discharge static electricity from your body by touching a known grounded surface,
such as your computer's metal chassis.
• Keep the autoloader turned off during all installation procedures.
• Use an antistatic wrist strap.
• Keep static-sensitive parts in their original shipping containers until ready for
installation. Look for the ESD sticker to identify static sensitive parts.
• Avoid touching connectors and other components.
Preparing for Rack
Mounting 0The autoloader can be rack mounted by attaching it directly to stationary cabinet rails.
Take the following general safety steps before beginning the rack-mount installation.
1Lower the cabinet feet.
2Extend the cabinet anti-tip device, if available.
3Ensure that the cabinet and all rack mounted equipment have a reliable ground
connection.
4Verify that the total current of all rack mounted components (including the
autoloader) will not exceed the current rating of the power distribution unit or outlet
receptacles.
5Secure the help of at least one other person. At least two people are required to safely
install the autoloader into a rack cabinet.
Note: Dry climates and cold-weather heating environments have lower relative
humidity and are more likely to produce static electricity.
Note: An anti-tip device may be extendable legs or similar equipment used to
stabilize the cabinet. This anti-tip equipment is to help avoid over-
balancing the cabinet when installing or removing equipment.
Warning: Failure to take these safety steps may result in personal injury or
equipment damage.
4Unpacking the Autoloader
SuperLoader™ 3 Quick Start Guide
Unpacking the Autoloader
Before you begin, clear a desk or table so that you can unpack the autoloader.
The Quantum SuperLoader 3 Quick Start Guide
has all the necessary information to unpack
and inspect your autoloader correctly.
You also need to select an open 2U computer rack location near the server that will host
the autoloader.
Carefully unpack and inspect your new Quantum SuperLoader 3 by doing the following:
1Inspect the shipping box for damage. If you notice any damage, report it to the
shipping company immediately.
2Open the shipping box and remove the accessories package. Set the accessories
package aside for now.
3Lift the autoloader and padding out of the box and place it on the work surface, top
facing up. Do not set the autoloader on either end or sides.
4Carefully remove the shipping padding from the left and right sides of the
autoloader. Then remove the bag from the autoloader.
5Remove the foam insert from the magazine bay of the autoloader. Save the packing
materials in case you need to move or ship the autoloader in the future.
Caution: Do not remove the top cover of the autoloader during the installation
process. Removing the top cover could result in damage to the
autoloader.
Caution: If the room in which you are working differs from the temperature in
which the autoloader was shipped or stored by 15° C (30° F) or more, let
the autoloader acclimate to the surrounding environment for at least 12
hours before removing it from the shipping carton.
Caution: If your unit was ordered as a one-magazine autoloader, be sure to remove
the plastic shipping insert from the magazine bay before connecting or
operating your autoloader. Insert either a magazine or a magazine blank
into the bay. The autoloader will not function without both magazine bays
equipped with either a magazine or a magazine blank.
Note: If the cover must be taken off, there are 26 screws that need to be removed.
Unpacking the Autoloader 5
SuperLoader 3
Checking Accessories 0The following accessories are shipped with the Quantum SuperLoader 3:
• Quantum SuperLoader 3 Quick Start Guide
• SCSI tape drive kits
• SCSI host or server cable
• SCSI terminator (not included with Serial Attached SCSI)
• Fibre Channel tape drive kits
• Fibre Channel cable
•Ethernetcable
• Hardware to rack mount the autoloader (see figure 1)
• Four autoloader brackets (two long and two short to accommodate different rack
depths)
• Two support brackets
• Two sets (decimal and metric) of four support bracket 10-32 x 1/4 inch button
head screws (two per support bracket)
•TORX
®L-Key drivers (T8 and T10)
• One magazine blank
•Powercable
• Documentation CD containing all of the documentation in Adobe®Portable
Document Format (PDF)
•Barcodelabels
You will also need the following parts that were shipped with your rack:
• Eight clip nuts
• Eight rack screws
Figure 1 Rack Mount
Hardware
Short autoloader
brackets (72-A225-A)
Support brackets
(74-60605-01)
Long autoloader
brackets (72-A226-A)
Support bracket screws
72-A348-A (4) or 90-60227-50 (4)
6Rack Mounting the Autoloader
SuperLoader™ 3 Quick Start Guide
Rack Mounting the Autoloader
This section provides the steps for attaching the autoloader directly to the stationary rails
of a rack. Refer to table 1 for information on common rack hole types.
Table 1 Rack Hole Types
1Install two clip nuts, 1.75 in. (44.45 mm) apart, onto each of the four rails of the rack,
making sure that you install each pair of clip nuts at exactly the same level (see
figure 2).
Figure Description
Square rack holes are the most
common type of rack holes.
They can accept either cage
nuts which mount from the back
of the rail or clip nuts which clip
on from the side of the rack rail.
Through holes require clip nuts
to accept mounting hardware.
Threaded holes require neither
cage or clip nuts to accept
mounting hardware.
Note: The rails within the rack have a hole pattern that repeats throughout the rail.
Cage nut
Clip nut
Clip nut
Rack Mounting the Autoloader 7
SuperLoader 3
Figure 2 Installing Two Clip
Nuts
2Select the long or short autoloader brackets (depending on the depth of the rack), and
then attach them to the rear of the autoloader (see figure 3). Use the long autoloader
brackets (72-A226-A) when the distance from the front mounting rail to the rear
mounting rail is less than 30.25 in. (76.84 cm). Otherwise, use the short autoloader
brackets (72-A225-A).
Outer covers
of the rack
Rail
Rail
Rail
Clip nut
1.75 in
(44.45 mm)
Clip nut
8Rack Mounting the Autoloader
SuperLoader™ 3 Quick Start Guide
Figure 3 Attaching Autoloader
Brackets
3Using rack screws, attach a support bracket to the clip nuts on each rear rail (see
figure 4).
Tighten the screws just enough to hold the support brackets firmly against the rail
while still allowing the support bracket to be slightly shifted by hand. This shifting
will help facilitate the engagement of autoloader brackets as the autoloader is
installed in the rack. You will fully tighten the screws in step 8.
Note: Be sure to attach the support brackets correctly; the side of the bracket with
only two holes should be secured to the rail.
Autoloader
Autoloader bracket
Screws (10-32 x 1/4 only)
Rack Mounting the Autoloader 9
SuperLoader 3
Figure 4 Attaching Support
Brackets
4With the help of a second installer, insert the autoloader into the rack so that the
autoloader brackets slide into corresponding support brackets on the rear rails and
the tabs at the front of the autoloader align flush with the clip nuts on the front rails
(see figure 5).
Caution: Do not release the front end of the autoloader until it can be secured to
the rack.
Support bracket
Rack screws
Clip nuts
Rear rail in rack
Outer cover of rack
10 Rack Mounting the Autoloader
SuperLoader™ 3 Quick Start Guide
Figure 5 Sliding Autoloader
into Rack
5While the other installer holds the front end of the autoloader, secure the front end of
the autoloader to the rack using four rack screws (two per tab) as shown in figure 6.
Tighten the screws just enough to secure the autoloader to the front rails.
Figure 6 Front Alignment
6Install four screws (two per side) to secure the support brackets to the autoloader
brackets (see figure 7).
Support bracket
Autoloader bracket
Front rail
Rack screws
Tab (one per side)
Autoloader
(front)
Autres manuels pour Superloader 3
7
Table des matières
Autres manuels Quantum Stockage
Quantum
Quantum Atlas V Manuel utilisateur
Quantum
Quantum DLT 1 Manuel utilisateur
Quantum
Quantum DLTtape DLT 7000 Manuel utilisateur
Quantum
Quantum StorNext QD6000 Manuel utilisateur
Quantum
Quantum Superloader 3 Manuel
Quantum
Quantum PX500 Series Manuel utilisateur
Quantum
Quantum ValueLoader DLT VS160 Manuel utilisateur
Quantum
Quantum DLTtape DLT1 Manuel utilisateur
Quantum
Quantum Scalar LTFS Manuel d'utilisation et d'entretien
Quantum
Quantum Scalar 50 Manuel utilisateur
Quantum
Quantum DLT-V4 Manuel utilisateur
Quantum
Quantum LTO-4 (Model B) Manuel utilisateur
Quantum
Quantum PX500 Series Mode d’emploi
Quantum
Quantum P4000 Series Manuel utilisateur
Quantum
Quantum Scalar 24 Manuel utilisateur
Quantum
Quantum DLT-S4 Manuel utilisateur
Quantum
Quantum FastStor 1 Manuel utilisateur
Quantum
Quantum StorNext QD6000 Manuel utilisateur
Quantum
Quantum StorNext QD7000 Manuel utilisateur
Quantum
Quantum PX500 Series Manuel utilisateur
Manuels Stockage populaires d'autres marques
Spectra Logic
Spectra Logic T-Series Spectra T50e Manuel utilisateur
Panasonic
Panasonic LKM-F931-1 Manuel utilisateur
Tabernus
Tabernus Enterprise Erase E2400 Manuel utilisateur
Rocstor
Rocstor COMMANDER 3F series Manuel utilisateur
HP
HP P9000 Manuel utilisateur
Western Digital
Western Digital Ultrastar Data60 Manuel utilisateur