Quantum StorNext QM1200 Manuel utilisateur
StorNext QM1200/QS1200/QS2400 Expansion Unit
Replacing a Power-Fan Canister
6-67554-02 Rev B *6-67554-02 B*
ii Replacing a Power-Fan Canister
StorNext QM1200/QS1200/QS2400 Expansion Unit, Replacing a Power-Fan Canister, 6-67554-02 Rev B, April 2015,
Product of USA.
Quantum Corporation provides this publication “as is” without warranty of any kind, either express or implied, including
but not limited to the implied warranties of merchantability or fitness for a particular purpose. Quantum Corporation
may revise this publication from time to time without notice.
COPYRIGHT STATEMENT
© 2015 Quantum Corporation. All rights reserved.
Your right to copy this manual is limited by copyright law. Making copies or adaptations without prior written
authorization of Quantum Corporation is prohibited by law and constitutes a punishable violation of the law.
TRADEMARK STATEMENT
Quantum, the Quantum Logo, Backup. Recovery. Archive. It's What We Do., Be Certain, Be Quantum Certain, DLT, the DLT
Logo, DLTSage, DLTtape, the DLTtape Logo, DXi, DXi Accent, Dynamic Powerdown, FastSense, FlexLink, GoProtect,
GoVault, iLayer, Lattus, MediaShield, Optyon, Pocket-sized., Well-armored., Preserving the World's Most Important Data.
Yours., Q-Cloud, Quantum Certain, Quantum Certainty, Quantum vmPRO, Scalar, SDLT, SiteCare, SmartVerify,
StorageCare, StorNext, Super DLTtape, SuperLoader, and Vision are either registered trademarks or trademarks of
Quantum Corporation and its affiliates in the United States and/or other countries. All other trademarks are the property
of their respective owners.
Products mentioned herein are for identification purposes only and may be registered trademarks or trademarks of their
respective companies. All other brand names or trademarks are the property of their respective owners.
Quantum specifications are subject to change.
StorNext QM1200/QS1200/QS2400 Expansion Unit - Replacing a Power-Fan Canister April 2015
Quantum Corporation
- 1 -
Replacing a Power-Fan Canister in the StorNext
QM1200/QS1200/QS2400 Expansion Unit
Use these procedures to replace a failed power-fan canister in the StorNext QM1200/QS1200/QS2400 Expansion Unit.
Before you start to replace the power-fan canister in the StorNext QM1200/QS1200/QS2400 Expansion Unit, gather
antistatic protection and the appropriate replacement power-fan canister (AC power or DC power)
Locating the Failed Power-Fan Canister
1. Refer to Figure 1 to locate the power-fan canisters within the expansion unit.
Figure 1 Power-Fan Canister Locations
1. ESM A
2. ESM B
3. Power-fan canister A
4. Power-fan canister B
2. Check the Power-Fan Service Action Required LED to locate the failed power-fan canister (Figure 2).
If a fault is detected, the amber Power-Fan Service Action Required LED is on. If you can safely remove the
power-fan canister, the blue Power-Fan Service Action Allowed LED is on.
Possible equipment damage – If you perform this procedure with the power turned on, you must
complete it within three minutes to prevent the possibility of overheating the equipment.
StorNext QM1200/QS1200/QS2400 Expansion Unit - Replacing a Power-Fan Canister April 2015
Quantum Corporation
- 2 -
Figure 2 LEDs on a Power-Fan Canister
1. Standby Power LED (Green)
2. Power-Fan Output DC Power LED (Green)
3. Power-Fan Service Action Allowed LED (Blue)
4. Power-Fan Service Action Required LED (Amber)
5. Power-Fan Input AC Power LED (Green)
Gathering Support Data/Unpacking Power-Fan Canister
Before you start to replace the power-fan canister in the expansion unit, gather antistatic protection and a
replacement AC power-fan canister.
You can determine whether you have a failed power-fan canister in two ways:
The Recovery Guru directs you to replace a failed power-fan canister.
You locate the failed power-fan canister by checking the amber Power-Fan Service Action Required LED.
1. Gather support data through one of the following methods:
—Use the storage management software to collect and save a support bundle of your storage array. From the
Array Management Window, select Monitor >> Health >> Collect Support Data. Then name and specify a
location on your system where you want to store the support bundle.
—Use the command line interface (CLI) to run the save storageArray supportData command to
gather comprehensive support data about the storage array. For more information about this command,
refer to Command Line Interface and Script Commands. Running this command can temporarily impact
performance on your storage array.
2. Did the Recovery Guru direct you to replace a failed power-fan canister?
—Yes – Go to step 4.
—No – Run the Recovery Guru to identify the failed component, and go to step 3.
3. If the Recovery Guru has directed you to replace the power-fan canister and the blue Power-Fan Service Action
Allowed LED is not on, use either the command line or the GUI to prepare the power-fan canister for removal
a. On the command line, type this command and press Enter:
SMcli <ctrl_IP1> -c “Set tray [trayID] powerfanCanister [left|right] service
Allowed Indicator=on;”
In this command:
—<ctlr_IP1>is the identifier of the controller to which the expansion unit is assigned.
ATTENTION Possible hardware damage – To prevent electrostatic discharge damage to the tray, use proper
antistatic protection when handling tray components.
StorNext QM1200/QS1200/QS2400 Expansion Unit - Replacing a Power-Fan Canister April 2015
Quantum Corporation
- 3 -
—[trayID]is the identifier of the expansion unit that contains the power-fan canister that you want to
replace. Drive tray ID values are 0 to 99. Be sure to type the square brackets around the identifier.
—[left|right] is the identifier of the power-fan canister you want to replace. Valid values are left or
right. Be sure to type the square brackets around the value.
b. On the GUI, click on the image of the tray that contains the power-fan canister you want to replace. From the
Array Management Window toolbar, select Hardware >> Prepare for Removal.
4. Put on antistatic protection.
5. Unpack the new power-fan canister.
a. Set the new power-fan canister on a flat, static-free surface near the expansion unit.
b. Save all packing materials in case you need to return the power-fan canister.
Removing the Power-Fan Canister
1. Turn off the Power switch on the power-fan canister that has failed (Figure 3).
Figure 3 AC Power Switch on the Drive Tray
1. AC Power Switch
2. Remove the plastic strain relief from the power cord.
3. Unplug the power cord from the failed A power-fan canister.
4. Remove the power-fan canister from the expansion unit (Figure 4 on page 4).
a. Rotate the latches outward to disengage the power-fan canister.
b. Use the latches as handles to pull the power-fan canister out of the expansion unit.
NOTE While removing the power-fan canister, you might notice an increase in fan speed. The fan speed returns to normal after you
have replaced the power-fan canister.
StorNext QM1200/QS1200/QS2400 Expansion Unit - Replacing a Power-Fan Canister April 2015
Quantum Corporation
- 4 -
Figure 4 Removing a Power-Fan Canister
Installing the Power-Fan Canister
1. Slide the replacement power-fan canister all the way into the expansion unit. Rotate the latches towards the
center to lock the power-fan canister into place.
2. Make sure that the Power switch on the replacement power-fan canister is turned off, and plug in the power cord.
3. Attach the plastic strain relief to the power cord, and make sure that it fits snugly up against the power-fan
canister.
4. Turn on the Power switch on the replacement power-fan canister.
5. Check the Power-Fan Input AC Power LED, and the Power-Fan Service Action Required LED on the new power-fan
canister (Figure 2 on page 2).
6. Based on the LED status, perform one of these actions:
—The Power-Fan Input AC Power LED are on and the Power-Fan Service Action Required LED is off – Go to
step 8.
—The Power-Fan Output DC Power LED and the Power-Fan Input AC Power LED are off or the Power-Fan
Service Action Required LED is on – Check that the power-fan canister is installed correctly. Reinstall the
power-fan canister. Go to step 7.
7. Did this action correct the problem?
—Yes – Go to step 8.
—No – If the problem has not been resolved, contact your Customer and Technical Support representative.
8. Using the LEDs and the storage management software, check the status of all of the trays in the storage array.
9. Does any component have a Needs Attention status?
StorNext QM1200/QS1200/QS2400 Expansion Unit - Replacing a Power-Fan Canister April 2015
Quantum Corporation
- 5 -
—Yes – Click the Recovery Guru toolbar button in the Array Management Window, and complete the recovery
procedure. If the problem has not been resolved, contact your Customer and Technical Support
representative.
—No – Go to step 10.
10. Remove the antistatic protection.
11. Gather support data on your updated storage array through one of the following methods:
—Use the storage management software to collect and save a support bundle of your storage array. From the
Array Management Window, select Monitor >> Health >> Collect Support Data. Then name and specify a
location on your system where you want to store the support bundle.
—Use the CLI to run the save storageArray supportData command to gather comprehensive support
data about the storage array. For more information about this command, refer to Command Line Interface and
Script Commands. Running this command can temporarily impact performance on your storage array.
Autres manuels pour StorNext QM1200
4
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels Quantum Stockage
Quantum
Quantum PX500 Series Guide de démarrage rapide
Quantum
Quantum DXi4700 Manuel utilisateur
Quantum
Quantum StorNext QD6000 Manuel utilisateur
Quantum
Quantum StorNext M660 Instructions d'installation
Quantum
Quantum Bigfoot 1.2AT Manuel utilisateur
Quantum
Quantum DXi6700 series Manuel technique
Quantum
Quantum DXi4601 Manuel utilisateur
Quantum
Quantum LTO-4 (Model B) Manuel utilisateur
Quantum
Quantum Scalar 50 Manuel utilisateur
Quantum
Quantum DLT Series Instructions d'installation
Quantum
Quantum Q2000 Manuel utilisateur
Quantum
Quantum DLTtape DLT 2000 Manuel
Quantum
Quantum DAT 72 Manuel utilisateur
Quantum
Quantum DLT-V4 Manuel
Quantum
Quantum ValueLoader LTO-1 Manuel utilisateur
Quantum
Quantum RDX 8000 Manuel utilisateur
Quantum
Quantum DLTtape DLT 7000 Manuel utilisateur
Quantum
Quantum ActiveScale P100E3 Manuel utilisateur
Quantum
Quantum DLTtape DLT 4000 Manuel utilisateur
Quantum
Quantum Fireball Plus AS Manuel utilisateur
Manuels Stockage populaires d'autres marques
Spectra Logic
Spectra Logic T-Series Spectra T50e Manuel utilisateur
Panasonic
Panasonic LKM-F931-1 Manuel utilisateur
Tabernus
Tabernus Enterprise Erase E2400 Manuel utilisateur
Rocstor
Rocstor COMMANDER 3F series Manuel utilisateur
HP
HP P9000 Manuel utilisateur
Western Digital
Western Digital Ultrastar Data60 Manuel utilisateur