Pyronix Enforcer Manuel utilisateur

Installation Manual

EN50131-1:2006+A1:2009

EN50131-3:2009

EN50131-6:2008

EN50131-5-3:2005+A1:2008

PD6662:2010+IA:2015

Software Version >10

PIEZO WARNING

The Enforcer system contains a

100dBA siren, please be aware

of this after an activation

RINS1903-1

Enforcer

Time 10:09 c

CONTENTS PAGE

1. Introduction ............................................................................................................................3

1.1 System Overview.................................................................................................................3

2. Specification and Warranty ........................................................................................................4

2.1 Technical Specification..........................................................................................................4

3. Installation Guide .....................................................................................................................5

3.1 Mains and Earth Wiring.........................................................................................................5

3.2 Inside of the Enforcer: Rear .................................................................................................6

3.3 Inside of the Enforcer: Front ................................................................................................6

3.4 Connecting / Replacing the Control Panel Battery .....................................................................7

3.5 Important Installation Notes..................................................................................................7

3.6 RS232 Connection / Uploading and Downloading Software.........................................................8

3.7 Input / Output Board............................................................................................................9

3.8 Connecting Peripherals to the I/O Board .................................................................................9

3.9 Connecting a Wired Input Expander......................................................................................12

3.10 Connecting a Wireless Input Expander ................................................................................12

3.11 Connecting an Output Expander ......................................................................................... 13

3.12 Digi Wi-Fi (Wi-Fi Module). .................................................................................................14

3.13 Other Module Options ....................................................................................................... 14

3.14 Product Information .........................................................................................................14

3.15 Warranty ........................................................................................................................14

Default Codes:

Master Manager Code: 2222

Engineer Code: 1111

Enforcer: Installation Manual

Page: 3

1. Introduction

The Enforcer is a wireless alarm system that has been designed to enable easy installation and minimal

maintenance. The Enforcer protects the property (domestic or commercial) with a multitude of unique

features:

• Two Way Wireless Protection

• Signal Strength Indicator (SSI)

• Instant Two Way Device Control

• Pyronix High Security Wireless Protocol Encryption

• Programmable Wireless Supervision Time

• Intelligent Wireless Jamming Detection

1.1 System Overview

Areas: 4 (4 Levels/Areas)

Wireless Inputs (max): 64 (32 x onboard, 1 x EURO-ZEM32-WE )

Wired Inputs (max): 34 (2 x inputs on I/O board (Inputs 33-34) and 4 x ZEMs

(Inputs 35-66)

Total Inputs: 66

Outputs (max): 38 (1 x output module and 3 x outputs on I/O board, 4 on each ZEM

if EURO-ZEM8+ or EURO-ZEM8+PSU are used, 1 on each RKP)

User / Manager Codes: 80 (Max 32 x wireless keyfobs)

Duress / Guard Codes: 10

Code Combinations: 4294967295 (fully encrypted rolling code)

Communications: DIGI-GPRS, DIGI-LAN, DIGI-WI-FI, DIGI-GSM, DIGI-PSTN, DIGI-

PSTN/VOICE

Arming Devices (max): 4 wired keypads (EURO-LCDPZ) and/or 4 wireless keypads

(LEDRKP-WE). Internal or External Tag Readers.

Sirens: 2 Wireless Sirens or 2 Wired Sirens (in SCB mode)

Logs: 750

Remote Arm and Soak Test: 

Event Signalling to UDL: 

Memory Type: EEPROM

Compliant to EN Grade*:2

Environmental Class: II

NOTE : All wireless learning is performed in the ‘WIRELESS DEVICE CONTROL’menu, refer to the

programming manual for more details.

Compliance labelling should be removed or adjusted if non-compliant configurations are used.

Please note that technical functions for example fire, gas and flooding are not security graded as they are

outside the scope of EN50131-1 and EN50131-3.

Enforcer: Installation Manual

Page: 4

2. Specification and Warranty

2.1 Technical Specification

Enforcer Mains Inputs

European rated voltage 230V AC -15/+10%

European rated current 83mA

Capable operating voltage 90 - 264V AC

Current 222mA - 75mA

Rated Frequency 50 / 60Hz

Input Fuse Rating T 2A (cannot replace)

PSU Type A

Radio Frequency 868MHz, FM Transceiver Narrow Band

Enforcer Battery

Output instant voltage 12.71V (with no mains and battery fully charged)

Peak to peak ripple voltage 10mVpk

Battery low voltage cut off value 8.5V

Type NiMH 8 cell 2200mAh rechargeable battery

CIE current when operating on battery backup 90mA

Environment

Physical Dims 220 x 160 x 50mm

Weight 1025g

Operating Temp -10°C to +40°C

Nominal Temp -10°C to +50°C

Storage Temp -20°C to +60°C

I/O Board (If Connected)

Inputs 2 Wired (DEOL, SEOL)

Output Voltage 13.2 VDC (nominal)

Max Current for PGM Output 70mA

SAB Outputs 250mA Continuous Load

Bus Fuse F500mA 250V Bus Fuse

Aux Fuse F500mA 250V Aux Fuse

Systems Analysis: Inputs (Max 66)

On Board 32 Wireless

I/O Board 2 Wired

Input Modules 4 Wired (8 wired input each): EURO-ZEM8, EURO-ZEM8+ or

EURO-ZEM8+PSU

1 Wireless (32 wireless inputs): EURO-ZEM32-WE

Systems Analysis: Outputs (Max 40)

I/O Board 3 Wired

Keypads/Readers 3 Wired: EURO-LCDPZ, EUR-107

Input Module 16 Wired: EURO-ZEM8+

Output Module 1 Wired: EURO-OEM8R8T or EURO-OEM16R+PSU

1 Wireless: EURO-ZEM32-WE

2 x Fuses F500mA 250V

System Analysis: Additional Devices

Keypads Up to 3

Readers Up to 3

Bell Boxes 2

Wireless Arming Stations 4

Enforcer: Installation Manual

Page: 5

3. Installation Guide

NOTE 1: It is recommended that the Engineer menu is accessed prior to opening a powered Enforcer.

NOTE 2: If any new peripheral is installed (i.e. Modem, I/O board, Expander) it is recommended that the

Enforcer is powered down (mains and battery).

1. Slightly unscrew the two screws

located at the bottom.

NOTE: Do not fully unscrew at

these can be used as a 'hanger' to

the rear casing as shown in Step

2. Unhinge the Enforcer from the top

and pull down to disconnect.

NOTE: Take extra care when

removing the front of the Enforcer as

modems, I/O boards etc may be

connected to the front.

3. Hang the front of the Enforcer

on the opening screws at the

bottom if required. Shown below.

3.1 Mains and Earth Wiring

It is important that the electrical earth connection is connected when connecting the 240V mains

supply to the Enforcer.

NOTE 1: Do not locate the mains cables next to internal cabling.

NOTE 2: Ensure that the Enforcer is not mounted on any metal surfaces.

NOTE 3: That the mains cables should not be internally 'looped' as shown. This may interfere with

the wireless antenna's. Where possible it is recommended that all mains cables should be installed

through the area nearest the mains terminals as shown above.

NOTE 4: If cable management is an issue, a spacer is available: ENF/SPACER-WE

Enforcer: Installation Manual

Page: 6

3.2 Inside of the Enforcer: Rear

1. Terminals for Earth and Mains Supply.

2. If a modem is required (DIGI-PSTN, DIGI-

PSTN/VOICE, DIGI-GPRS, DIGI-LAN or DIGI-WI-

FI) then this space is used to install them.

3. The transformer is situated in a housing.

4. The rear tamper adjustment screw is used if

the tamper from the front of the Enforcer isn't

sitting flush to the back plate - this may happen

if the Enforcer is installed on an uneven surface.

5. If an I/O board is installed, then this space is

used to install it.

3.3 Inside of the Enforcer: Front

1. RS232 connection for Up/downloading to

the InSite software.

2. Where the control panel battery is located.

3. The power connection for a communications

module if connected.

4. The connection for an I/O board if

connected.

5: The connection for a communication module

to be installed.

6: The power connection (+15V DC) for the

Enforcer.

Enforcer: Installation Manual

Page: 7

3.4 Connecting / Replacing the Control Panel Battery

1. Unscrew the battery

compartment

2. Connect the battery pack 3. Close the battery

compartment masking sure no

battery cable is trapped

underneath.

NOTE: The Enforcer back up battery must be replaced by the

manufacturer’s recommendation. The part code for this battery is BATT9V6/2Ah1-WE.

The battery is NiMH 8 cell 2200mAh rechargeable.

Install the batteries in the space provided and connect the battery connector to the

two pins as shown above. Reinstall the battery holder cover and dispose of the batteries in

accordance with the local regulations.

3.5 Important Installation Notes

Ensure wiring is done to the national wiring regulations in the country where the installation is

taking place. In the UK, this is BS 7671 Requirements for electrical installations; IET Wiring

Regulations (17th edition). If in doubt, consult a local qualified electrician.

Ensure that a readily accessible disconnect device incorporated in the premises installation wiring

shall be provided external to the equipment with a contact separation of at least 3,0mm and

connected as closely as possible to the supply.

Ensure that the Input and Output Board (I/O Board) used to connect wired keypads, readers,

inputs and outputs to the Enforcer, and is only connected to circuits operating at SELV voltage.

When securing external wires, ensure that means are provided in the installation to prevent the

SELV or signal circuits from coming into contact with live parts of the power supply circuit. Wires

should be fixed near their terminal blocks.

The end of stranded conductor shall not be consolidated by soft soldering at places where the

conductor is subjected to contact pressure.

On completion of wiring use tie-wraps to prevent any loose wires causing a safety hazard (material

of cables tie shall be rated at least HB or better).

Cables ties and hoses shall be separate for power supply cable and SELV wirings.

Size of protective bonding conductors: minimum section 1.5mm².

Enforcer: Installation Manual

Page: 8

3.6 RS232 Connection / Uploading and Downloading Software

The Enforcer PC software (InSite) can be downloaded from http://www.pyronix.com/pyronix-

downloads.php. To enable the Enforcer to receive upload/download commands, refer to the function

‘SET UP DOWNLOAD’ in the programming manual.

Serial Connection (RS232)

1. Open up InSite.

2. Click on Roving Dial Customer.

3. Enter the panels’ Engineer code.

4. Enter the site name.

5. (This can be found in SYSTEM OPTIONS->SYSTEM DISPLAYS in the panel on site).

6. Enter the Name.

7. The little green box which displays RS232 in the bottom left of the Insite screen should turn

yellow when connecting and when connected switch to blue.

Cloud Connection

1. Open up InSite.

2. Click on ‘Roving Dial Customer.’

3. Set ‘Dial Out Mode’ to ‘Cloud’.

4. Enter the ‘System ID’

5. Enter the panels’ ‘System Password.’

6. Enter the ‘Site Name.’ (This can be found in SYSTEM OPTIONS->SYSTEM DISPLAYS in the panel on

site).

7. Enter a Name. (Enter Customer in Database As)

8. Click dial.

9. The little green box which displays Cloud at the bottom of the Insite screen should turn yellow

when connecting and when connected switch to blue.

Enforcer: Installation Manual

Page: 9

3.7 Input / Output Board

The Input/output (I/O) board contains the RS485 terminals that are used to connect additional wired

keypads, readers, input expanders and output expanders .

Terminals:

D1-: RS485 0V

D2+: RS485 +12V

D3: RS485 'A' Bus

D4: RS485 'B' Bus

PGM1: Programmable Output

BELL: Bell output for a wired external

sounder

STRB: Strobe output for a wired external

sounder

Z33: Wired Input 33

COM: Common terminal for Z33 and Z34

+12V: +12V auxiliary supply

Z34: Wired Input 34

The maximum devices the I/O board can have on the RS485 bus are as follows:

4 x Input Expanders: EURO-ZEM8, EURO-ZEM8+, EURO-ZEM8+PSU or ZEM32-WE

1 x Output Expander: EURO-OEM8R8T or EURO-OEM16R+PSU

3 x Keypads/Readers (same bus): EURO-LCDPZ, EUR-107 or EUR-108

3.8 Connecting Peripherals to the I/O Board

Connecting Keypads (EURO-LCDPZ)

Up to 3 additional keypads can be connected to the Enforcer. These will be addressed

individually and also addressed in the Engineer function '‘Assign Keypads / Readers’.

Addressing at the keypad

Each keypad will also need to be addressed individually, press and hold the Dkey until

‘SECURITY CODE’ is displayed. Enter ‘2000’ and select the desired address (the first keypad that

is connected should be addressed as ‘1’). Press the akey to save the data and exit.

Enforcer: Installation Manual

Page: 10

Connecting Internal Tag Readers (EUR-107)

Up to 3 readers can be connected to the Enforcer. Each keypad or reader need to be addressed

as described below. These will also need assigning in the Engineer function '‘Assign Keypads /

Readers’.

Addressing at the Reader

Address 1 = SWITCH 1 ON.

Address 2 = SWITCH 2 ON.

Address 3 = SWITCH 1: ON, SWITCH 2: ON.

NOTE: If using the EUR-107 as access control/entry control please refer to the peripheral

instructions for connection details

Connecting External Tag Readers (EUR-108)

If an additional external reader is connected, this will need to be assigned in the programming,

‘Assign Keypads/ Readers’. Each reader will also need to be addressed individually via connecting

certain wires to ground.

Addressing at the Reader

Address 1: Brown, Orange to GND

Address 2: Brown, Green to GND

Address 3: Brown to GND

NOTE: If using the EUR-108 as access control/entry control please refer to the peripheral

instructions for connection details

Autres manuels pour Enforcer

Table des matières

Autres manuels Pyronix Système de sécurité

Pyronix

Pyronix Enforcer 32WE Manuel utilisateur

Pyronix

Pyronix ENFORCER RINS1706-1 Manuel de service

Pyronix

Pyronix Enforcer 32-W Manuel utilisateur

Pyronix

Pyronix Enforcer 32WE Manuel utilisateur

Pyronix

Pyronix PCX 256 Manuel utilisateur

Pyronix

Pyronix OCTAGON II Manuel utilisateur

Pyronix

Pyronix EURO 46 V10 Manuel utilisateur

Pyronix

Pyronix Enforcer 32WE Manuel utilisateur

Pyronix

Pyronix Paragon E Instructions d'installation

Pyronix

Pyronix Matrix 424 Manuel utilisateur

Pyronix

Pyronix Enforcer Manuel utilisateur

Pyronix

Pyronix ENFORCER V11 Mode d'emploi

Pyronix

Pyronix XDL12TT-AM Manuel utilisateur

Pyronix

Pyronix 256 Guide de l'utilisateur

Pyronix

Pyronix Enforcer 64 Manuel utilisateur

Pyronix

Pyronix PARAGON E Manuel utilisateur

Pyronix

Pyronix STERLING 10 Manuel utilisateur

Pyronix

Pyronix Enforcer 32WE Manuel utilisateur

Pyronix

Pyronix ENFORCER Series Manuel du propriétaire

Pyronix

Pyronix Enforcer V10 Manuel utilisateur

Pyronix

Pyronix EURO 46 APP Manuel utilisateur

Pyronix

Pyronix RINS1902-2 Manuel utilisateur

Pyronix

Pyronix HOMECONTROLHUB Manuel utilisateur

Pyronix

Pyronix PCX 256 Manuel du propriétaire

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur