Pulsar V071 Manuel utilisateur
CAL. V071, V072
ALARM CHRONOGRAPH
ENGLISH
●Analogue time display
●Digital time and calendar
●Daily alarm
●60-minute stopwatch
●Illuminating light
English
English
32
PM
SCREW DOWN CROWN
[for models with screw down crown]
Locking the crown
1Turn Crown counterclockwise until you no
longer feel the threads turning.
2Crown can be pulled out.
1Push Crown back in to normal position.
2Turn Crown clockwise while pressing it lightly
until tight.
DISPLAY AND CROWN/BUTTONS
Unlocking the crown
AWith each press, the mode in the digital display changes in the
following order:
TIME ALARM
➡➡
CALENDAR
➡
STOPWATCH
➡
MODE CHANGE
CROWN
a b
a: Normal position
b: Extended position
C
Digital display
* The shape of the digital
display differs depend-
ing on the calibre.
B
A
English
English
54
TIME/CALENDAR SETTING
CALENDAR SETTING
DIGITAL TIME SETTING
●Before setting the analogue time, be sure to set the digital time.
APress to show TIME mode.
▲
Press for 2 to 3 seconds.
B
▲
B
▲
C
▲
▲
A
or
B
Select the digits to be adjusted.
Set the flashing digits.
Return to TIME mode.
APress to show CALENDAR
mode.
▲
Press for 2 to 3 seconds.
B
▲
B
▲
C
▲
▲
A
or
B
Select the digits to be adjusted.
Set the flashing digits.
Return to CALENDAR mode.
Selection of the digits
Seconds ➾Minutes ➾ Hour ➾ 12-/24-hour indication
➾
(Press for 2 to 3 seconds.)
➾
TIME mode
B
A
PM
C
Selection of the digits
Date ➾Month ➾ Day of the week ➾ CALENDAR mode
➾
(Press for 2 to 3 seconds.)
Date Day
Month
B
A
PM
C
Hour Minutes Seconds
English
English
76
ANALOGUE TIME SETTING
●Before setting the analogue time, be sure to set the digital time. (See the previous
section)
1Pull out when the second hand is
at the 12 o’clock position.
2Turn to set the hour and minute
hands.
3Push back in to normal position
when the second digits count “00”
in the digital time display.
CROWN
ALARM
ALARM TIME SETTING
APress to show ALARM mode.
▲
B
▲
C
▲
▲
A
or
B
Select the digits to be adjusted.
Set the flashing digits.
Return to ALARM mode.
Selection of the digits
Hour ➾Minutes ➾ ALARM mode
➾
Second hand
PM
Hour
hand Minute
hand
➠
➠
B
PM
C
A
ALARM mode mark
Hour Minutes
English
English
98
STOPWATCH
ALARM ENGAGEMENT/DISENGAGEMENT
With each press in ALARM
mode, the alarm is engaged
and disengaged alternately.
C
TURNING ON/OFF OF HOURLY TIME SIGNAL
With each simultaneous press
in CALENDAR or TIME mode,
the hourly time signal is turned
on and off alternately.
B
&
C
* At the designated time, the alarm
rings for 20 seconds.
To stop it manually, press any of
the buttons.
●The stopwatch measures up to 60 minutes in 1/100 second increments.
PM
Alarm engaged
Alarm
mark
C
PM
Hourly time signal turned on
Hourly time
signal mark
C
B
PM
Split time measurement
C
START
▲
B
SPLIT
▲
B
SPLIT
RELEASE
▲
• • • • • • • C
STOP
▲
B
RESET
Minutes Seconds 1/100 seconds
CStart / Stop / Restart
B
Split /
Split release / Reset
English
English
1110
TIME/CALENDAR SETTING
NOTES ON OPERATING THE WATCH
[CALENDAR SETTING]
●The calendar automatically adjusts for odd and even months except February of leap
years.
●The flashing digits move quickly if button C is kept pressed.
●If the watch is left untouched with the digits flashing, it will automatically return to the
CALENDAR mode in 1 to 2 minutes.
[DIGITAL TIME SETTING]
●The flashing digits except the seconds and 12-/24-hour indication move quickly if button
C is kept pressed.
●In second setting, when the seconds count any number from “30” to “59” and button
C is pressed, one minute is added and the seconds are reset to “00”.
●When setting the hour digits in the 12-hour indication, check that AM/PM is properly set.
Only the “PM” mark is displayed. For the AM setting, there is no indication.
●If the watch is left untouched with the digits flashing, it will automatically return to the
TIME mode in 1 to 2 minutes.
[ANALOGUE TIME SETTING]
●When setting the minute hand, first advance it 4 to 5 minutes ahead of the desired time
and then turn it back to the exact minute.
Measurement of two competitors
ILLUMINATING LIGHT
Press and hold in TIME or
CALENDAR mode.
C
PM
C
* The light illuminates the digital
display for easy viewing in the
dark.
C
START
B
FINISH TIME
OF 1ST
COMPETITOR
▲
C
2ND
COMPETITOR
FINISHES
▲
▲
B
FINISH TIME
OF 2ND
COMPETITOR
▲
B
RESET
English
English
1312
BATTERY CHANGE
Battery life : Approx. 3 years
Battery : SEIKO SR927W
●If the alarm is used more than once a day, the stopwatch more than once a day, and/
or the illuminating light for more than one second a day, the battery life may be less
than the specified period.
●As the battery is inserted at the factory to check the function and performance of
the watch, its actual life once in your possession may be less than the specified
period.
●When the battery expires, be sure to replace it as soon as possible to prevent any
malfunction.
●We recommend that you contact an AUTHORIZED PULSAR DEALER for battery
replacement.
3
Years
●Necessary procedure after battery change
After the battery is replaced with a new one, or in case an abnormal display (broken
digits, etc.) appears in the digital display, follow the procedure below to reset the IC.
Press buttons A, B and C at the same time. All the segments of the
●
When the crown is pulled out or pushed in for time setting, the minute hand may move
slightly. However, this is not a malfunction.
STOPWATCH
●
With each press of button C, the light illuminates the digital display with a beep.
●
After measuring 60 minutes, the stopwatch will start counting again from “00'00"oo”
as many times as necessary until it is stopped.
●
Restart and stop of the stopwatch can be repeated by pressing button C.
●
Measurement and release of split time can be repeated by pressing button B.
●
When measuring a long period of time, press button A to return the STOPWATCH mode
to the CALENDAR or TIME mode after the stopwatch starts. This will prevent any
possible malfunction.
ALARM
[ALARM TIME SETTING]
●
When the time function is displayed in the 24-hour indication, the alarm will also be
displayed in the 24-hour indication.
●
The flashing digits move quickly if button C is kept pressed.
●
When setting the hour digits in the 12-hour indication, check that AM/PM is properly set.
Only the “PM” mark is displayed. For the AM setting, there is no indication.
●
If the watch is left untouched with the digits flashing, it will automatically return to the
ALARM mode in 1 to 2 minutes.
●Alarm test:
The alarm can be tested by keeping buttons B and C pressed in the
CALENDAR or TIME mode.
English
English
1514
TO PRESERVE THE QUALITY OF YOUR WATCH
digital display will light up, a beep will sound twice and then “January
1st, Sunday” will be displayed in the digital display.
* Before using the watch, set the time/calendar and alarm.
WARNING
●Do not remove the battery from the watch.
●If it is necessary to take out the battery, keep it out of the reach of
children. If a child swallows it, consult a doctor immediately.
●Never short-circuit, tamper with or heat the battery, and never expose
it to fire. The battery may burst, become very hot or catch fire.
CAUTION
●The battery is not rechargeable. Never attempt to recharge it, as this
may cause battery leakage or damage to the battery.
WATER RESISTANCE
●Non-water resistant
●Water resistance (5 bar)*
If “WATER RESISTANT 5 BAR”
is inscribed on the case back, your
watch is designed and manu-
factured to withstand up to 5 bar
5
bar WR
and is suitable for swimming, yachting and taking
a shower.
If “WATER RESISTANT 10 BAR”,
“WATER RESISTANT 15 BAR”
or “WATER RESISTANT 20 BAR”
is inscribed on the case back,
10/15/20
bar WR
●
Water resistance (10 bar/15 bar/20 bar)*
your watch is designed and manufactured to
withstand up to 10 bar/15 bar/20 bar and is
suitable for taking a bath, shallow diving, but not
for scuba diving. We recommend that you wear a
PULSAR Diver’s watch for scuba diving.
If “WATER RESISTANT” is not
inscribed on the case back, your
watch is not water resistant, and
care should be taken not to get it
If “WATER RESISTANT” is inscribed
on the case back, your watch is
designed and manufactured to
withstand up to 3 bar, such as acci-
●Water resistance (3 bar)
dental contact with splashes of water or rain, but it is
not designed for swimming or diving.
wet as water may damage the movement. If
the watch becomes wet, we suggest that you
have it checked by an AUTHORIZED PULSAR
DEALER or SERVICE CENTER.
English
English
1716
* Before using the water resistance 5, 10, 15 or 20 bar watch in water, be sure the
crown is pushed in completely.
Do not operate the crown when the watch is wet or in water. If used in sea water,
rinse the watch in fresh water and dry it completely.
* When taking a shower with the water resistance 5 bar watch, or taking a bath with
the water resistance 10, 15 or 20 bar watch, be sure to observe the following:
• Do not operate the crown when the watch is wet with soapy water or shampoo.
• If the watch is left in warm water, a slight time loss or gain may be caused. This
condition, however, will be corrected when the watch returns to normal
temperature.
NOTE:
Pressure in bar is a test pressure and should not be considered as corresponding
to actual diving depth since swimming movement tends to increase the
pressure at a given depth. Care should also be taken on diving into water.
TEMPERATURES
+50°C
-5°C
Your watch works with stable
accuracy within a temperature
range of 5°C and 35°C (41°
F and 95°F).
Temperatures over 50°C
(122°F) or below –5°C (+23°F) may
cause a slight time loss or gain or
battery leakage or shorten the
battery life.
However, the above conditions will
be corrected when the watch
returns to normal temperature.
NS
The analogue unit of your
watch will be adversely
affected by strong
magnetism, though the
digital unit will not be
affected. Keep the watch away from
close contact with magnetic objects.
MAGNETISM
CARE OF CASE AND BRACELET
To prevent possible
rusting of the case and
bracelet caused by dust,
moisture and perspiration,
wipe them periodically
with a soft dry cloth.
Light activities will not
affect your watch, but be
careful not to drop your
watch or hit it against hard
surfaces, as this may
cause damage.
SHOCKS & VIBRATION
Be careful not to expose
the watch to solvents,
mercury, cosmetic spray,
detergents, adhesives or
paints. Otherwise, the
CHEMICALS
case, bracelet, etc. may become
discolored, deteriorated or damaged.
English
18
If your watch has a
protective film and/or a
sticker on the case back,
be sure to peel them off
before using your watch.
PRECAUTION REGARDING
CASE BACK PROTECTIVE FILM
It is recommended
that the watch be
checked once every
2 to 3 years. Have
your watch checked
by an AUTHORIZED PULSAR
DEALER or SERVICE CENTER
to ensure that the case, crown,
buttons, gasket and crystal seal
remain intact.
2 - 3
Years
PERIODIC CHECK
The IC (Integrated
Circuit) used in your
watch will be affected
by static electricity
which may disturb the
display. Keep the watch away
from close contact with objects
such as TV screens which emit
strong static electricity.
STATIC ELECTRICITY
Autres manuels pour V071
1
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Pulsar Montre
Pulsar
Pulsar V657 Manuel utilisateur
Pulsar
Pulsar CAL. W440 Manuel utilisateur
Pulsar
Pulsar VX50 Manuel utilisateur
Pulsar
Pulsar VD73 Manuel utilisateur
Pulsar
Pulsar YM22 Manuel utilisateur
Pulsar
Pulsar W850 Manuel utilisateur
Pulsar
Pulsar W671 Manuel utilisateur
Pulsar
Pulsar VJ22 Manuel utilisateur
Pulsar
Pulsar Pulsar ANALOGUE Manuel utilisateur
Pulsar
Pulsar Z46H Manuel utilisateur
Pulsar
Pulsar NX02 Manuel utilisateur
Pulsar
Pulsar Linetic Series Manuel utilisateur
Pulsar
Pulsar VD51 Manuel utilisateur
Pulsar
Pulsar W854 Manuel utilisateur
Pulsar
Pulsar V33J Manuel utilisateur
Pulsar
Pulsar W170 Manuel utilisateur
Pulsar
Pulsar W880 Manuel utilisateur
Pulsar
Pulsar VD50 Manuel utilisateur
Pulsar
Pulsar VX32 Manuel utilisateur
Pulsar
Pulsar Y182 Manuel utilisateur
