Pro-Ject Audio Systems Pro-Ject VC-S Manuel utilisateur

INSTRUCTIONS FOR USE

Pro-Ject VC-S

Controls, features and connections

1 Vacuum arm* (adhesive velvet strips attached)

2 Clamp* (base plate)

3 Fixing screw for base part of clamp*

4 Ventilation outlet and drain hole

5 Main switch with mains power cord socket

6 Vacuum on/off switch

7 Motor on/off direction switch

8 Vinyl record (not included)

9 Screwable clamp - top plate* with self-adhesive record label seal* (earlier versions: top plate

of clamp + screwable ball knob, groove with rubber for sealing record label)

10 Hexagon screw for motor flange height adjustment (see page 6)

11 Spindle with motor flange

12 Vacuum arm flange

13 Self-adhesive record label seal*

Accessories (included, but not shown above)

Wash it

vinyl cleaning concentrate (100ml bottle, mixing ratio 1:10 - 1:20)*

2 Goat hair brush*

3 Replacement adhesive strips for vacuum arm*

4 Drain insert (spout)*

5 AC power cord*

Optional accessories (available on request)



Wash it

cleaning concentrate, mixing ratio 1:10 - 1:20

bottle sizes: 100ml/250ml/500ml/1l (100ml ≙ 135 records / both sides, this average quantity

depends on dilution ratio and the amount of ready-to-use cleaning fluid used per application)

Goat hair brush

Adhesive strips for vacuum arm

Cover it VC-S (dust cover with hinges and mounting screws)

Dear music lover,

Thank you for purchasing a Pro-Ject Audio Systems record cleaning machine.

In order to achieve maximum performance and reliability, please study these instructions carefully.

Warning of a hazard for the user, the unit or possible misuse

Important notice

During assembly and adjustment small parts can be easily lost if they are not carefully placed in a suitable

receptacle. Before beginning assembly, please familiarize yourself with the parts listed above which are

correspondingly numbered in the technical diagram. Separately packed items are marked with an asterisk*.

Safety instructions

AC outlet voltages vary from country to country. Before connecting to your wall outlet, make sure that

the voltage in your area meets the voltage requirements printed on the device.

Hold the end of the plug when unplugging the power cord. Never handle the power cord while your

hands are wet or damp.

Never place any open flame sources, like burning candles, on or near the device. Do not operate in

damp or wet locations, such as near to a bathtub, sink, swimming pool or any other similar locations.

Keep plastic bags away from children to prevent any risk of suffocation.

Do not cover any ventilation holes (one is located on the left side and others are on bottom).

During operation this unit will generate loud noises, so we recommend the use of hearing protectors

during longer cleaning sessions. Check the unit after transportation for signs of damage, if a damage

is found, do not operate the unit and contact your dealer!

The unit is capable of long time running however in such case platter spindle may get hot and whole

platter/clamp area as well as air coming out from the unit may get warm. The temperature of the

platter can´t damage vinyl records. In order to keep the temperature as low as possible do not

expose the unit to direct sunlight.

The VC-S motor should not be turned on when not cleaning your records. Extended running time

outside of the guideline process can cause over-heating.

Setting up the unit

The unit is supplied assembled with the exception of the platter and vacuum arm which are packed

separately. Remove all parts from the transport packaging carefully. Please see the diagram above for

assembly instructions. Base part of the clamp (2) should be attached by using the screw (3), a Phillips head

screwdriver is required but not included. Then apply the self-adhesive label seal (13) on top.

Using the unit

Please ensure that all assembly and set up steps have been followed as outlined in this manual. All 3 rocker

switches ("main switch", "motor" and "vacuum" should be in position "0"). Connect the power cord to the

socket on the rear side of VC-S and turn the main switch to the "I" position.

Place a record on the bottom plate. Using moderate force, thread the top clamp plate on the threaded tip of

the centre spindle. Do not over-tighten. If the top plate and screw clamp are too loose, the record will not

turn even if the motor is running.

While the record is turning apply a generous amount of ready-to-use cleaning fluid (6 - 8ml) to the record

while holding the brush horizontally and gently pressing against the record, spread the fluid across the

surface of a the record. Use only the necessary amount of fluid (6 – 8ml), enough to cover the record, not

the machine!

Cleaning efficiency can be significantly improved by applying appropriate force on the cleaning brush.

Even more cleaning improvement can be achieved by using warmed-up

Wash It

cleaning fluid.

Wash It

can be warmed in a microwave oven up to 40 degrees Celsius, please check temperature to avoid

record damage. Dilution ratio of warmed-up

Wash it

should be 1:20.

Wash It

is non-flammable and

non-toxic. Please note that you are doing all this at your own risk.

Please do not apply

Wash it

concentrate directly to the record!

The motor can turn both directions or can be stopped during the application of the fluid, depending on your

personal preference. To change direction, choose the "I" position for clockwise rotation or to the “II” position

for counter-clockwise rotation.

It is recommended that you use the brush to clean the record in both directions before vacuuming. For better

dissolving of impurities, wait a few seconds (longer in the case of heavily soiled records) before starting the

vacuuming process.

Once the record has been thoroughly cleaned in both directions, place the vacuum arm above the record

pointing at the spindle until it reaches its lock position.Turn the Vacuum motor to the “I” position. After the

cleaning fluid has been thoroughly vacuumed, switch off the vacuum, followed by the motor. Return the

vacuum arm into its rest position and wait a few seconds for the record to dry thoroughly. Unscrew the top

clamp plate, turn the record over and repeat steps for the opposite side of the record.

The VC-S is equipped with automatic overheating protection, which switches the motor off in case of

excessive usage. After a cool-down period, the VC-S will return to its fully operational status.

Preparation of Wash it concentrate to get ready-to-use cleaning fluid

The cleaning concentrate is usable for vinyl and shellac records and should be diluted before application:

Mix 1 part of

Wash it

concentrate with 10-20 parts of distilled / demineralized water!

1:10 is better for old and dirty records. For common cleaning or cleaning with warmed-up cleaning

fluid a dilution ratio of 1:20 is sufficient.

Caution! Earlier

Wash it

fluid (or concentrate) containing alcohol is only suitable for

12” and 7”

vinyl records. Most 78rpm records are made of shellac which is sensitive to some cleaning agents.

Please only use

Wash it

without alcohol when cleaning 78rpm shellac records!

Maintenance and cleaning

Your record cleaning machine requires little to no regular maintenance.

A water level gauge is located on the left side of the unit, below the air outlet hole. The internal tank has a

substantial capacity and subsequently takes a long time to reach full capacity. Once the water level reaches

the point marked " ←MAX", the tank should be emptied:

1. Remove the plastic grill from the ventilation outlet and draining hole (4)

2. Place the drain insert spout into the hole (drain insert is included in the accessory box)

3. Lift the opposite side of the VC-S up to drain the unit reservoir

Regularly check the velvet strips on the arm. Make sure they are clean, no dirt or debris is present.

Prior to maintenance, always disconnect the record cleaning machine from the power outlet!

Installing the dust cover (Cover it VC-S is an optional accessory)

The holes for lid hinges are pre-drilled on the back side of the unit. Each hinge is attached with 2 screws

(supplied with the lid).

Fit the lid carefully over the hinge prongs and adjust the screws until the lid stays open at the angle of your

preference without being too stiff to open or close.

Technical specifications Vinyl Cleaner VC-S

Nominal speed 30 r.p.m.

Power consumption 230V/800W, 120V/650W

Dimensions (W x D x H) 435 x 335 x 280 mm (fully assembled)

Weight 10,5kg (netto)

Fuse 230V/120V T5A/T6A

Potential incorrect use and fault conditions

Pro-Ject products are manufactured to the highest standards and undergo strict quality controls before

leaving the factory. Faults that may possibly occur are not necessarily due to material or production faults but

can sometimes be caused by incorrect use. Some of these faults are as follows:

The platter doesn't turn although the unit is switched on:

The power cord is not connected to the unit.

The power cord is not plugged in to the AC wall outlet.

Broken fuse in the main switch.

Overheating protection is active.

Top clamp plate is not tightened properly.

How to adjust the height of VC-S’ record clamp

The VC-S is pre-adjusted to spec for normal standard 80 g records. The vacuum arm works best when it is

parallel to the record when operating and the adhesive strips is pressed gently on the surface of record. If the

vacuum suction arm is not in the correct distance from the record it may not be able to completely vacuum the

cleaning fluid. In this case it may be necessary to adjust the height of the clamp. Especially 180 g pressing need

a different set up of the distance. You will need a Phillips screwdriver (to unscrew the set screw of the clamp

base part) and a 2.5mm hexagon key (to loosen motor spindle):

1. Disassemble the clamp (2) by unscrewing the set screw (3) from the motor flange spindle (11)

2. Insert the 2.5mm hexagon key into the hole on the side of motor flange (11)

3. Loosen the hexagon screw, until the flange can be moved up or down

4. When the correct height position is found, fasten the hexagon screw and mount the clamp (2)

You do not need to fully disassemble the flange from the motor!

Service

Should you encounter a problem which the above information does not able to alleviate or identify, please

contact your dealer for assistance.

Guarantee repairs will only be affected if the unit is returned correctly packaged. For this reason we recommend

keeping the original packaging.

Never return a record cleaning machine without making sure that is it safely disassembled and correctly

packaged in the original packaging.

Warranty

The manufacturer accepts no responsibility for damage caused by not adhering to these instructions

for use and/or by transportation without the original packaging. Modification or change to any part

of the product by unauthorized persons will void the manufacturer’s warranty.

Pro-Ject Audio Systems is a Registered Trademark of

H. Lichtenegger.

This guide was produced by: Pro-Ject Audio Systems

The information was correct at the time of printing.

The manufacturer reserves the right to make

changes to the technical specification without prior

notice as deemed necessary to uphold the ongoing

process of technical development.

Table des matières

Autres manuels Pro-Ject Audio Systems Platine

Pro-Ject Audio Systems

Pro-Ject Audio Systems VC-S2 ALU Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems 9 Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Xtension Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pro-Ject RPM 9.1 SuperPack 1 Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Remote Box S2 Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems VTA it Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems 12 Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems 9 Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pro-Ject 6 PerspeX SuperPack Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Essential Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Align it PRO Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems ESSENTIAL III Guide de dépannage

Pro-Ject Audio Systems

Pro-Ject Audio Systems Debut Carbon RecordMaster HiRes Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems RPM 1.3 Genie Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pro-Ject RPM 10 Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Pro-Ject RPM 9.1 Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems X1 Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Debut Carbon RecordMaster HiRes Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems 1 Xpression Carbon Classic Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Essential II DIGITAL Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems 1 Xpression III Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems 1 Xpression Carbon Classic Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems T1 Phono SB Manuel utilisateur

Pro-Ject Audio Systems

Pro-Ject Audio Systems Primary E Phono Manuel utilisateur

Manuels Platine populaires d'autres marques

Gemini

Gemini CDT-05 MKII Manuel utilisateur

Rotel

Rotel RP-820 Manuel utilisateur

Shuman

Shuman MC-250BT Manuel utilisateur

Stanton

Stanton STR8-150 Manuel utilisateur

Audio Technica

Audio Technica AT-LPW40WN Manuel utilisateur

Crosley

Crosley McQueen CR7011-GY Manuel utilisateur

Reloop

Reloop SMP-1 Manuel utilisateur

auna

auna TT-Classic Plus Manuel utilisateur

COMO AUDIO

COMO AUDIO Turntable Analog Manuel utilisateur

Dual

Dual 1009 F Manuel utilisateur

REED

REED Muse3C Manuel utilisateur

AXIOMTEK

AXIOMTEK OPS883-H Series Manuel utilisateur

Pioneer

Pioneer PL-71 Manuel utilisateur

Vestax

Vestax PDX-a1 Manuel utilisateur

Denon

Denon DP-400 Manuel utilisateur

Dual

Dual 504 Manuel utilisateur

Audio-Techica

Audio-Techica AT-LP60XBT Manuel utilisateur

Goldring

Goldring G99 Manuel utilisateur