Premier Mounts SCM-103 Manuel utilisateur
INSTALLATION INSTRUCTIONS
SCM-103
Suspended Ceiling Mount
NORTH AMERICA
3130 East Miraloma Avenue
Anaheim, CA 92806 USA
USA and Canada –
Phone: 800-368-9700
Fax: 800-832-4888
EUROPE
Swallow House,
Shilton Industrial Estate,
Shilton, Coventry, England CV79JY
Phone: +44 (0) 2476 614700
Fax: +44 (0) 2476 614710
AUSTRALIA, NEW ZEALAND,
OCEANIA (DISTRIBUTOR)
P.O. Box 295
Mordialloc Victoria 3195
Australia
Phone: 039586 6330
www.premiermounts.com.au
Other Locations – Phone: (001)-714-632-7100; Fax: (001)-714-632-1044
©Premier Mounts 2008
9531-027-224-02
Page 2 Installation Instructions
Table of Contents
Warning Statements
Warning Statements 2
Parts List 3
Installation Tools 3
Locating the Mounting Points 4
Mounting the Brackets to the Display 5
Securing the Lower Cover 6
Securing the Tubes to the Mounting Brackets 6
Lifting the Display into Position 8
Cable Routing 9
Installing the Beauty Covers 12
Technical Specifications 14
Warranty 15
SCM-103
Redundancy in Engineering is the duplication of critical components of a system with the intention of increasing reliability of the system, usually in the
case of a backup or fail-safe.
IT IS REQUIRED THAT THE INSTALLATION LOCATION BE INSPECTED AND APPROVED BY A
LICENSED STRUCTURAL ENGINEER.
PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS SHOULD BE READ AND COMPLETELY
UNDERSTOOD. THE INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY AND PROPERTY DAMAGE. KEEP
THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE.
PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS PRODUCT FOR
PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR MODIFI-
CATIONS, AND IS NOT RESPONSIBLE FOR ANY DAMAGES, CLAIMS, DEMANDS, SUITS, ACTIONS OR CAUSES OF ACTION OF WHATEVER
KIND RESULTING FROM, ARISING OUT OF OR IN ANY MANNER RELATING TO ANY SUCH USE, ATTACHMENTS OR MODIFICATIONS.
THE SURFACE MUST BE CAPABLE OF SUPPORTING AT LEAST FIVE TIMES THE WEIGHT OF THE DISPLAY. IF NOT, THE CEILING
STRUCTURE MUST BE REINFORCED. THE MAXIMUM WEIGHT THAT CAN BE USED WITH THIS PRODUCT IS 2000LBS. PROPER
INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN, AS OUTLINED IN THE INSTALLATION INSTRUCTIONS, MUST BE
ADHERED TO. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY, OR EVEN DEATH.
SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT. USE PROPER SAFETY GEAR
AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY.
At least two qualified people should perform the assembly procedure. Injury and/or damage can result from dropping or mishandling the display.
If mounting to studs, make sure that the mounting screws are anchored into the center of the studs. Use of an edge-to-edge stud finder is recommended.
This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal injury.
Do not install near sources of high heat. Do not install on a structure that is prone to vibration, movement or chance of impact
Contact Premier Mounts with any questions
(800) 368-9700
Installation Instructions Page 3
Parts List
This ceiling mount is shipped with all proper installation hardware and components. Make sure that none of these
parts are missing and/or damaged before beginning installation. If there are missing and/or damaged parts, please
stop the installation and contact Premier Mounts (800-368-9700).
Recommended Installation Tools
Mounting Bracket Covers
(Qty 2)
Mounting Brackets
(Qty 2)
Display Input Cover
(Qty 1)
Tubing
(Qty 3)
Lower Cover Panel
(Qty 1)
Lower Cover
(Qty 1)
Plastic Coupler Inserts
(Qty 4)
8-32 x 3/8” Phillips
Screws (Qty 18)
8-32 x 1/2” Phillips Screws
(Qty 6)
10-32 Kep Nut
(Qty 4)
6-32 x 1/4” Set Screw
(Qty 4)
Clevis Pins
(Qty 6)
SCM-103
Spirit Level (Supplied)1/2” Socket and Wrench
Tape Measure
Screwdriver
Pencil Stud Finder
1/8” Allen wrench (Supplied)
1/16” Allen wrench (Supplied)
Page 4 Installation Instructions
Locate the Mounting Points
The display comes with four (4) M16 screws with quick release sleeves that are pre-installed on the display.
Mounting
Points
Mounting
Points
Step 1. Locate the 4 quick release sleeves on the back of the display and remove. Place the M16 bolts and split washers to the side.
These will be used for bracket installation on the next page.
SCM-103
Installation Instructions Page 5
Mounting the Brackets to the Display
Step 1. Align the mounting bracket holes up with the mounting holes on the back of the display. There are two mounting holes used on
each side of the display.
Step 2. Place the split washer between the display and the mounting bracket.
Step 3. Insert the M16 mounting bolt through the mounting bracket then through the split washer into the display.
Step 4. Tighten the bolt into place and repeat the steps for the remaining three bolts.
The following steps will require a minimum of 3 people. This should not be done with less then 3 people due to the
weight of mounting brackets.
Right Mounting
Bracket
Left Mounting
Bracket
Split Washer
M16 Bolt
DO NOT OVERTIGHTEN THE M16 BOLTS. DOING SO MAY RESULT IN DAMAGE TO
THE DISPLAY. TIGHTEN TO MANUFACTURERS SPECIFICATIONS.
SCM-103
Page 6 Installation Instructions
Step 1. Insert the lower cover between the vertical mounting brackets.
Step 2. Attach four (4) 10-32 Kep Nuts and tighten down securing the lower cover into place.
Step 3. Insert two (2) 8-32 x ½” screws and tighten down the lower cover bracket against the vertical side mounting brackets.
Securing the Lower Cover
THE SCM-103 IS HEAVY. IT IS STRONGLY RECOMMENDED THAT THREE PEOPLE PERFORM ALL
INSTALLATION STEPS.
8-32 x ½”
Screw
10-32 Kep Nut
Securing Tubes to Mounting Brackets
Step 1. Slide the tubes into the cut outs on the side of the mounting brackets.
Step 2. Slide the tubes in enough to have an even amount showing on each side of the left & right mounting brackets.
Step 3. Once tubes are slid into place, tighten all twelve (12) pre-installed set screws located in the display mounting brackets using the
1/8” Allen wrench (supplied). These screws are installed at the factory and are used to lock the tubes into place.
SCM-103
Factory
Installed Set
Screw
Pre Installed
Handy Box
Lower Cover
Installation Instructions Page 7
THE SCM-103 IS HEAVY. IT IS STRONGLY RECOMMENDED THAT THREE PEOPLE PERFORM ALL
INSTALLATION STEPS.
Now that the mount is attached to the display, double check all mounting locations to insure all hardware is
properly tightened and secured.
Step 5. Once the tubes are locked into place insert the clevis pins into the hole at the end of each tube.
Step 6. Lock each clevis pin into place by inserting the attached cotter pin into the hole.
Cotter Pin
2” Tube
Clevis Pin
SCM-103
Page 8 Installation Instructions
THE SCM-103 IS HEAVY. IT IS STRONGLY RECOMMENDED THAT THREE PEOPLE PERFORM ALL
INSTALLATION STEPS.
Lifting the Display into Position
Step 1. Raise the display to the desired height (Refer to the display manufacturer specs on raising the display into position and the
different options available).
IN THE NEXT STEP A LIFTING DEVICE SUCH AS A FORKLIFT , SCISSOR LIFT, OR HOIST WILL NEED TO
BE UTILIZED IN ORDER TO LIFT DISPLAY INTO POSITION. NOT DOING SO COULD RESULT IN PERSON-
AL INJURY OR DAMAGE TO THE DISPLAY.
Pre-Hung
Cable
Scissor Lift
Display Sucured to
Pallet
Fork Lift
SCM-103
The display may be hung from a ceiling structure using two (2) main support cables and two (2) safety cables. Length,
mounting location and method of attachment will be provided by the installer. The components (below) that are used
to hang the SCM-103 are sold separately and may be ordered through Premier Mounts (800) 368-9700.
1/4” stainless steel 7 x 19 wire rope assembly w/
1/2” - 20 NF stainless steel threaded stud with
3-1/2” thread min. on one end only
1/2-20 NF hex nut
(Qty 18)
Flat Washer
(Qty 8) Cable Access Channel
1/2-20 Threaded Stud
1/4” Cable
1/4” Redundancy Cable
Support Bar
1/2-20 Hex Nut and Flat Washer
1/2-20 Threaded Stud
Bracket Cover
1/2-20 Hex Nut and Flat Washer
1/4” Steel Thimble
Installation Instructions Page 9
Cable Routing
Pre-Hung
Cable
2 Hole
Locations for
Cable Routing
Two holes are provided at the top of each mounting bracket. Cables can be routed so both are going through one hole or
routed so each cable runs through its own hole.
The system is designed to allow for 2 cables on each mounting bracket. 1 cable for support & 1 as a safety redundancy
cable.
Step 1. Route the pre-hung cables through the top of the left and right mounting brackets attached to the display.
Step 2. Locate the plastic insert plugs and slip around cable
through the cut out in the side of the insert.
Plastic Insert
Plug
SCM-103
Page 10 Installation Instructions
THE SCM-103 IS HEAVY. IT IS STRONGLY RECOMMENDED THAT THREE PEOPLE PERFORM ALL
INSTALLATION STEPS.
Step 5. Route the cable down through the provided holes
on the display mounting bracket.
6-32 x 1/4”
Set Screw
Step 3. Slide plastic insert plug down cabling and
insert into the top of the mounting bracket. A cut
out in the mounting bracket is provided that will
allow the plastic cap to sit flush with the top of
the mounting bracket
Step 4. Locate the 6-32 x 1/4” Set Screw and insert
into the sides of the plastic top locking the plastic
plug into position. The set screw location is on
the side of each plastic top. Tighten the set screw
using 1/16” Allen wrench.
Cable Routing Holes
SCM-103
Plastic Top
Table des matières
Autres manuels Premier Mounts Support et étagère
Premier Mounts
Premier Mounts PTM Manuel utilisateur
Premier Mounts
Premier Mounts Convergent Series Manuel utilisateur
Premier Mounts
Premier Mounts PTM-B Manuel utilisateur
Premier Mounts
Premier Mounts LMVSP Manuel utilisateur
Premier Mounts
Premier Mounts USA Manuel utilisateur
Premier Mounts
Premier Mounts PRF Manuel utilisateur
Premier Mounts
Premier Mounts Convergent UNI-UPS-A CLD Manuel utilisateur
Premier Mounts
Premier Mounts RTM Series Manuel utilisateur
Premier Mounts
Premier Mounts Universal Flat-Only Mount UFM Manuel utilisateur
Premier Mounts
Premier Mounts ECM-3763D Manuel utilisateur
Premier Mounts
Premier Mounts PSD-TL Manuel utilisateur
Premier Mounts
Premier Mounts Rotary RTM-S Manuel utilisateur
Premier Mounts
Premier Mounts AM65 Manuel utilisateur
Premier Mounts
Premier Mounts AM300-B Manuel utilisateur
Premier Mounts
Premier Mounts Universal Tabletop Stand PSD-TTS/C Manuel utilisateur
Premier Mounts
Premier Mounts VPM Manuel utilisateur
Premier Mounts
Premier Mounts LMVLF Manuel utilisateur
Premier Mounts
Premier Mounts PP-FCTA-QL Manuel utilisateur
Premier Mounts
Premier Mounts LPSA3747 Manuel utilisateur
Premier Mounts
Premier Mounts CTM-MS2 Manuel utilisateur
Manuels Support et étagère populaires d'autres marques
Salamander
Salamander Acadia AC/W/L400/WH Manuel utilisateur
Fohhn
Fohhn VAT-09 Guide de l'utilisateur
ricoo
ricoo FS0522 Manuel utilisateur
AMSOIL
AMSOIL BMK-22 Guide rapide
Kargo Master
Kargo Master 48220 Manuel utilisateur
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur
