Precor DSL 505 Manuel de référence

SERVICE BULLETIN

SB.DSL.20170507 rev02

Contact Precor Customer Support at [email protected] or 800.786.8404 with any questions. Page - 1 - of 7

DSL 505 Rear Delt / Pec Fly Cable Repair

Applies to

DSL 505 Rear Delt / Pec Fly built prior to 5/16/2017

Issue/Symptoms

On some machines using the 1/8” diameter lift cables, the cam cables may twist and jam not allowing the arms to

properly lift and lower the weight stack.

Resolution

On machines using the 1/8” lift cables that exhibit this issue, replace the existing 1/8” cables with larger 3/16” diameter

cables.

Tools required

•Torque wrench with minimum 150 ft-lb torque fitted to 5/32-inch & 3/8-inch hex key bit sockets.

•#2 Phillips and Flat Blade screw drivers

•Socket wrench with 3/4-inch socket

•Adjustable wrench 0-1.5”

•3/4-inch open-end wrench

•5/32 inch and 3/8 inch hex key wrenches

Parts required

QTY

Part Number

Description

PPP00000CW38299101

CW38299-101 ASSY,CABLE,STK-SROD,119.88,DSRDPF(1)

PPP000CWCLNN172000

CWCLNN172-000 ASSY, CABLE, UPPER, PEC FLY/REAR DELT(1)

Note: 1) only replace cables on machines exhibiting this issue.

Procedure

Review entire procedure before starting.

Important:Take note of the upper cam and stack cable routing before beginning the removal procedure

(recommend taking pictures before cable removal).

Removal Procedure

1. Remove the stack shroud covers, see steps 1 thru 5 in the Shroud Assembly Guide (PN CW39990-101).

2. Remove all pulley covers using a #2 Phillips screw driver. Retain pulley covers and fasteners for installation.

Upper Cam Cable Removal

3. Disconnect the stack cable from the floating pulley bracket by removing

the stack Cable bolt using an adjustable wrench and 3/4” wrench. Retain

fasteners for installation.

SERVICE BULLETIN

SB.DSL.20170507 rev02

Contact Precor Customer Support at [email protected] or 800.786.8404 with any questions. Page - 2 - of 7

4. Disconnect the Cam cable from the left and right cams by removing the E- clip and Clevis Pins using a flat blade

screw driver. Retain fasteners for installation.

5. Remove the cable from the left and right cam redirect pulleys (pulley removal is not required).

6. Remove the upper cam cable from the floating pulley bracket (pulley removal is not required).

7. Remove the upper cam cable from the unit and discard.

Stack Cable Removal

8. Remove the base support pulley using a 3/8” hex key and 3/4” wrench and remove cable from the bracket.

Retain fasteners for installation.

SERVICE BULLETIN

SB.DSL.20170507 rev02

Contact Precor Customer Support at [email protected] or 800.786.8404 with any questions. Page - 3 - of 7

9. Remove the tower pulley guard cover using a 5/32” hex key. Retain tower guard and fastener for installation.

10. Remove the 5/16” shoulder bolt cable keeper from the lower tower stack pulley using a 5/23” hex key. Retain

hardware for installation.

11. Remove the two upper tower pulleys and cable keepers using a 3/8” hex key and 3/4” wrench. Retain pulleys

and fasteners for installation.

12. Loosen the weight stack cable jam nut using the 3/4” wrench and unscrew the cable bolt. Remove and discard

the stack cable from the unit.

SERVICE BULLETIN

SB.DSL.20170507 rev02

Contact Precor Customer Support at [email protected] or 800.786.8404 with any questions. Page - 4 - of 7

Installation Procedure

Stack Cable Installation Procedure

13. Attach the new stack cable to the top of the weight stack. Thread the new stack cable bolt into the weight

stack a minimum of six full turns (6 threads minimum) and lightly finger tighten the jam nut.

14. Thread the cable up through the weight tower frame. Replace the pulleys and cable retainers making sure that

the cable is seated properly in the pulleys and under the cable retaining keepers. Tighten the pulley bolts using a

3/8” hex key and 3/4” wrench and tighten to 124 ft-lb (168 N-m) of torque.

Note: When properly installed, the cable keeper brackets keep the cable securely seated in

the pulley. However, the keepers must not contact the cable while the unit is in use.

15. Route the cable down the left side of the stack and place around the lower stack pulley. Install the 5/16”

shoulder bolt cable keeper using a 5/23” hex key and tighten to 8 ft-lb (11 N-m) of torque.

SERVICE BULLETIN

SB.DSL.20170507 rev02

Contact Precor Customer Support at [email protected] or 800.786.8404 with any questions. Page - 5 - of 7

16. Next route the cable thru the base pulley support bracket. Install the base support pulley using the removed hex

bolt and nut using a 3/8” hex key and 3/4” wrench, tighten to 124 ft-lb (168 N-m) of torque.

Upper Cam Cable Installation Procedure

17. Attach one end to the upper cam cable to the cam using the E-clip and clevis pin.

18. Route the cable around the cam pulley, around the redirect pulley, thru the frame weldment cable opening,

around the vertical frame weldment pulley, and down to the floating bracket pulley.

SERVICE BULLETIN

SB.DSL.20170507 rev02

Contact Precor Customer Support at [email protected] or 800.786.8404 with any questions. Page - 6 - of 7

19. Hold the floating bracket with the tabs pointing up and carefully thread the cable under the pulley and up to the

cam frame weldment pulley.

20. Continue routing the cable from the floating bracket pulley over the cam frame weldment pulley, thru the frame

weldment cable opening, around the redirect pulley, and around the opposite cam to the cable attachment.

21. Attach the cam cable to the cam using the E-clip and Clevis Pin fastener.

22. Make sure that the cables to the floating bracket are straight and not twisted and that cable around the floating

pulley is properly seated.

23. Reinstall the tower pulley guard cover using a 5/32” hex key.

SERVICE BULLETIN

SB.DSL.20170507 rev02

Contact Precor Customer Support at [email protected] or 800.786.8404 with any questions. Page - 7 - of 7

24. Reinstall all removed pulley covers using a #2 Phillips screw driver.

Adjust the cable tension

25. Loosen the jam nut and adjust the stack cable bolt until the cable meets the following requirements:

•The top weight begins to separate from the second weight plate.

•The selector pin can easily be inserted into each of the weight plates.

•The add-on weight is selected when the latch is in the down position.

•At least six threads on the cable bolt extend into the selector stem.

26. Tighten the locking jam nut against the selector stem to 50 ft-lb (81 N-m) of torque.

27. Lift the top weight to relieve any cable twist and check the adjustment by inserting the weight pin into every

weight plate hole. The weight pin should slide easily in and out of each weight plate.

Note: The cable should be tight and the add-on weight should be selected when the lever is in the down

position.

28. Check cable pulleys, end connections, and end fittings. Make sure all connections are tight, adjusting cable

tension as necessary.

29. The distance from the underside of the stack cable bolt head to the top of the jam nut should be no more than

3/4-inch (19 mm).

30. Remove cable weight tension by lifting and pining the first weight plate

above the second weight plate. With no cable tension, verify that the

floating bracket upper cam cable is not twisted and the cable is straight.

Compete Installation

31. Reinstall the stack shroud covers, see the Shroud Assembly Guide (PN

CW39990-101).

32. Verify that the upper cam cable is correctly seated in the floating bracket

pulley and that the cable is not twisted and is hanging straight. Verify the

equipment operation and return to service.

Table des matières

Autres manuels Precor Équipement de fitness

Precor

Precor EFX 556 Manuel utilisateur

Precor

Precor move beyond S3.25 Guide rapide

Precor

Precor RESOLUTE LEG PRESS RSL 602 Manuel utilisateur

Precor

Precor Discovery Selectorized Line Manuel utilisateur

Precor

Precor Resolute Strength Selectorized RSL 208 Manuel utilisateur

Precor

Precor 718e Manuel utilisateur

Precor

Precor Resolute RSL 606 Manuel utilisateur

Precor

Precor Vitality Series Manuel utilisateur

Precor

Precor Experience 800 Series Manuel utilisateur

Precor

Precor Discovery Series Manuel utilisateur

Precor

Precor AB-103 Manuel utilisateur

Precor

Precor Stairclimber 800 Manuel utilisateur

Precor

Precor Discovery Selectorized Line Manuel utilisateur

Precor

Precor Discovery Series Manuel utilisateur

Precor

Precor CW-119 Manuel utilisateur

Precor

Precor move beyond C240 Manuel utilisateur

Precor

Precor Resolute RSL 619 Manuel utilisateur

Precor

Precor Vitality Series Manuel utilisateur

Precor

Precor Discovery Series Manuel utilisateur

Precor

Precor C524 Manuel utilisateur

Precor

Precor Discovery Series Manuel utilisateur

Precor

Precor Experience Series Manuel utilisateur

Precor

Precor C764 Manuel utilisateur

Precor

Precor Icarian Line Manuel utilisateur

Manuels Équipement de fitness populaires d'autres marques

NSD

NSD PB-188P Manuel utilisateur

Performance

Performance HyperVibe Manuel utilisateur

Scalamobil

Scalamobil S27 Manuel utilisateur

FYTTER

FYTTER RedMIUM BENCH BE-T6R Manuel utilisateur

Taurus

Taurus TF-RK1312 Manuel utilisateur

Nustep

Nustep T5 Manuel utilisateur

Movement

Movement BICEPS Idea Manuel utilisateur

Kegel8

Kegel8 V For Men Manuel utilisateur

Skandika

Skandika Styrke II Manuel utilisateur

BLK BOX

BLK BOX 21-0122-0B Manuel utilisateur

Stamina

Stamina aeropilates premier 299 Manuel utilisateur

SPORTSTECH

SPORTSTECH PBX300 Manuel utilisateur

ParaBody

ParaBody Serious Steel 877102 Manuel utilisateur

Weslo

Weslo Gym 650 Manuel utilisateur

Rebel

Rebel ACTIVE RBA-1011 Manuel utilisateur

4iiii

4iiii FLiiiight Manuel utilisateur

Image

Image 540 Manuel utilisateur

SteelFlex

SteelFlex PLHP Guide de démarrage rapide