PR Lighting PR5000 Manuel utilisateur

PR5000 Beam

This product manual contains important information about the safe installation and use of this

projector. Please read and follow these instructions carefully and keep this manual in a safe place

for future reference.

PR LIGHTING LTD.

http://www.pr-lighting.com

2/22

INDEX

SAFE USAGE OF THE PROJECTOR 3

INSTALLING THE PROJECTOR 4

FITTING THE LAMP 4

POWER SUPPLY – MAINS 5

CONTROL CONNECTIONS 5

DMX TERMINATOR 6

SETUP OPTIONS-PROJECTOR CONFIGURATION 6

TO SET THE DMX START ADDRESS 6

OPERATION MENU 8

ERROR MESSAGES 11

REPLACING GOBOS 11

DMX PROTOCOL 12

LED INDICATION 15

MAINTENANCE 15

LUBRICATION 15

KEEPING THE PROJECTOR CLEAN 15

TROUBLESHOOTING 16

TECHNICAL DATA 17

ELECTRICAL DIAGRAM 20

COMPONENT ORDER CODES 21

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change without

notice. Whilst every care is taken in the preparation of this manual we reserve the right to change specifications in the course of

product improvement. The publishers cannot be held responsible for the accuracy of the information herein, or any consequence

arising from them.

Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are in good

condition before installation and use. Should there be any damage caused by transportation, consult your dealer and do not use the

unit. Any damage caused by improper use will not be assumed by the manufacturer and / or dealer.

ACCESSORIES

These items are packed together with the projector:

Name Quantity Unit Remark

G clamps 2 Pcs

XLR cable 1 Pc 5-pin plug

Safety cord 2 Pcs

Spare gobos 4 Pcs

This manual 1 Pc

Ωclamps 2 Pcs Options

3/22

SAFE USAGE OF THE PROJECTOR

When unpacking and before disposing of the carton check there is no transportation damage before using the projector.

Should there be any damage caused by transportation, consult your dealer and do not use the apparatus.

The projector is for indoor use only, IP20. Use only in dry locations. Keep this device away from rain and moisture,

excessive heat, humidity and dust. Do not allow contact with water or any other liquids.

The projector is not designed or intended to be mounted directly on to inflammable surfaces.

The projector is only intended for installation, operation and maintenance by qualified personnel.

The projector must be installed in a location with adequate ventilation, at least 50cm from adjacent wall surfaces. Be sure

that no ventilation slots are blocked.

Do not project the beam onto inflammable surfaces, minimum distance is 5m. 5m

Avoid direct exposure to the light from the lamp. The light is harmful to the eye.

Do not attempt to dismantle and/or modify the projector in any way.

Electrical connection must only be carried out by qualified personnel.

Before installation, ensure that the voltage and frequency of power supply match the power requirements of the projector.

It is essential that each projector is correctly earthed and that electrical installation conforms to all relevant standards.

Do not connect this device to any other types of dimmer apparatus.

Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the power-cord come into contact

with other cables. Only handle the power-cord by the plug. Never pull out the plug by tugging the power-cord.

Keep the lamp clean. Do not touch the lamp glass with bare hand.

The projector should always be installed with a secondary safety fixing. A safety cord is supplied for this; it should be

attached as shown in “installing the projector” section.

The lamp used in this projector is a discharge lamp. After switching off don’t attempt to restart the projector until lamp has

cooled, this will require approx 15 minutes. Switching the lamp on and off at short intervals will reduce the life of both the

lamp and the projector. But occasional breaks will prolong the life of the lamp and projector.

Never run the projector without a lamp.

The lamp shall be changed if it has become damaged or thermally deformed.

Shields and lens shall be changed if they have become visibly damaged to such an extent than their effectiveness is

impaired, for example by cracks or deep scratches.

Exterior surface temperatures of the luminaire after 5 minutes operation is 80℃, when steady state is achieved 120℃,

There is no user serviceable parts inside the projector, do not open the housing and never operate the projector with the

covers removed.

Always disconnect from the mains, when the device is not in use or before cleaning it or

before attempting any maintenance work !

If you have any questions, don’t hesitate to consult your dealer or manufacturer.

4/22

INSTALL THE PROJECTOR

106

256

HANDLE

SAFETY CORD CLAMP

To pass 2 SAFETY CORDS

through 4 HOLES for safety!

WARNING

CONTROL PANEL

CLAMP

Take 2 clamps and 2 safety cords out from the package and mount 2 clamps on the underside of fixture with 2 retainers

attached to each clamp. Hang the fixture on the structure and fasten the screws attached to each clamp. (See the

WARNING on the underside of the base as shown above) To pass 2 SAFETY CORDS through 4 HOLES for safety!

Always ensure that the projector is firmly anchored to avoid vibration and slipping whilst functioning. Always ensure that

the structure that you are going to mount the projector is secure and is strong enough to support a weight of PR5000

Beam.

WARNING:

1. Unlock the PAN and TILT before the 1st application of projector for safety.

2. The projector MUST be lifted or carried by the HANDLES instead of clamps.

3. For safety the safety cord should afford 10 times of the unit’s weight.

FITTING THE LAMP

LAMP BACK COVER

FAST-FIT SCREWS

Lock the yoke before fitting/replacing the lamp.

Loosen 4 fast-fit screws and remove the back cover, you can see the structure as shown in the figure above.

Rotate the lampholder to the left and take out the worn-out lamp.

Fit new lamp and close the back cover by fastening 4 fast-fit screws. Note: don’t touch the bulb of the new lamp with

bare hand so as not to influence the beam output;

WARNING: The MSR series are high-pressure lamps with external igniters ( ). Care should always be taken

when handling these lamps.Always read the manufacturers "Instructions for use" enclosed with the lamp.

5/22

POWER SUPPLY-MAINS

Connect the power cord as follows:

L (live) =brown

E (earth) =yellow/green

N (neutral) =blue

Use the plug provided to connect the mains power to the projector paying attention to the voltage and frequency marked

on the panel of the projector. It is recommended that each projector be supplied separately so that they may be

individually switched on and off.

IMPORTANT

It is essential that each projector is correctly earthed and the electrical installation conforms to all relevant

standards.

CONTROL CONNECTION

Connection between controller and projector and between one projector and another must be made with a 2

core-screened cable, with each core having at least a 0.5mm diameter. Connection to and from the projector is via

cannon 3 pin (which are included with the projector) or 5 pin XLR plugs and sockets. The XLR's are connected as shown

in the figure above.

Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. The body of

the plug is not connected in any way. The unit accepts digital control signals in protocol DMX512 (1990).

Connect the controller’s output to the first fixture’s input, and connect the first fixture’s output to the second fixture’s input

and connect the rest fixtures in the same way. Eventually connect the last fixture’s output to a DMX terminator as shown

in the figure below.

TO TERMINATER

TO CONTROLLER

DMX IN DMX OUT DMX IN DMX OUT DMX IN DMX OUT

6/22

DMX TERMINATOR

In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This

prevents electrical noise from disturbing and corrupting the DMX control signals.

The DMX terminator is simply an XLR connector with a 120Ω(ohm) resistor connected across pins 2 and 3, which is

then plugged into the output socket on the last projector in the chain. The connections are illustrated below.

120

DMX TERMINATOR

CONNECTION

Connect a 120 (OHM) resistor

across pins 2 and 3 in an XLR plug

and insert into the DMX out socket

on the last unit in the chain.

PIN 3

PIN 2

SETUP OPTIONS-PROJECTOR CONFIGURATION

Projector configuration can be set conveniently via pressbutton switch and LCD display. Turn the projector on and the

LCD display will show DMX address you set and save last time and it can be reset and saved again as you please.

Launch the projector. Press button ENTER more than 5 seconds to unlock panel.

Press button UP or DOWN if you want to browse through the various Setup Options. There are 10 option codes

from DMX Address to Wireless options, and each code has a specific function. If you turn the encoder

knob clockwise, the function like as button UP . On the contrary, the function like as button DOWN .

Press button ENTER to save your settings or enter the next menu. There is same function if you push the encoder knob.

Press button UP or DOWN to shift.

Press button FUNC, it will return to the upper menu one by one. If you stay for minutes defaulted will show display status

automatically.

TO SET THE DMX START ADDRESS

Each projector must be given a DMX start address so that the correct projector responds to the correct control signals.

This DMX start address is the channel number from which the projector starts to “listen” to the digital control information

being sent out from the controller. PR5000 Beam have 3 DMX modes. There are standard mode, extended mode and

short mode. For example standard mode have 24 channels, so set the No. 1 projector’s address 001, No. 2 projector’s

address 025, No. 3 projector’s address 049, No. 4 projector’s address 073, and so on.

Launch the projector. Press button ENTER or encoder knob more than 5 seconds to unlock panel.

7/22

Press button FUNC to display DMX address;

Press button UP and DOWN, you can set the address;

Press button ENTER to confirm; In the same time. The GREEN LED will flash one time. It means the setting has

been enabled.

Press button FUNC, it will return to the upper menu one by one.

8/22

OPERATION MENU

1st LEVEL 2nd LEVEL 3rd LEVEL 4th LEVEL

PR LIGHTING

PR5000 BEAM DMX Address=XXX

DMX Address

Short Mode

Standard Mode

Extended Mode

Reset Rese

re You Sure?

Config Settings

DMX Mode

DMX M

Standard

DMX Mode

Extended

DMX Mode

Short

Lamp Control

Lamp Control B

Control Channel

Lamp

ontrol B

Power On

Lamp

ontrol B

DMX Presen

Loss of DMX

When DMX is Los

Normal Time Ou

When DMX is Los

Hold Last Value

Factory Settings

(Press button

DOWN/UP/ENTER at the

same time to enter the

sub-menu)

Fixture type

(WARNING：Never

change the fixture type

or the systemwill be

damaged!)

Option Settings

Colour Positions

STEPPED

Colour Positions

LINEAR

F-Gobo Positions

STEPPED

F-Gobo Positions

LINEAR

Pan DMX Invert

OFF

Pan DMX Invert

Tilt DMX Invert

OFF

Tilt DMX Invert

Pan Tilt Swap

OFF

Pan Tilt Swap

Dimmer Invert

OFF

Dimmer Invert

Iris Invert

OFF

Iris Invert

9/22

CMY Invert

OFF

CMY Invert

CTO Invert

OFF

CTO Invert

Defaults

OFF

Defaults

Restore Defaults

Display Options

Display Mode

Display

On Always

Display

Off After Delay

Display Invert

OFF

Display Invert

Display Dimming

Disp Dim Level

Min

Disp Dim Level

Full

Display Contrast Display Contrast

XXX(1~36, Default is 16)

Display Language

Language =

English

Language =

Chinese

Information

Lamp Hours Lamp Hours =

XX Reset Lamp Hours

Are You Sure?

Total Hours Total Hours =

Temperature

Display Board Display Board =

XX℃

Driver Board 1 Driver Board 1 =

XX ℃

Driver Board 2 Driver Board 2 =

XX ℃

Driver Board 3 Driver Board 3 =

XX ℃

Pan and Tilt Pan and Tilt =

XX ℃

10/22

Head Sensor Head Sensor=

XX ℃

Software Version

Display Board Display Board =

X.X.X

Driver Board 1 Driver Board 1 =

X.X.X

Driver Board 2 Driver Board 2 =

X.X.X

Driver Board 3 Driver Board 3 =

X.X.X

Pan and Tilt Pan and Tilt =

X.X.X

Power Board Power Board =

X.X.X

View DMX values DMX Channel

1=XXX

Electronic SN Electronic SN=

************

RDM Device Label

ANSI E1.20 RDM

Version

Test M o d e s

Factory Setup

OFF

Factory Setup

Self Test

OFF

self test

Lamp Manual

Control

Lamp Status Status = XXX

Control = X

Turn Lamp On

Turn Lamp Off

Wireless Options

Wireless Mode

Wireless First

Wireless Mode

XLRFirst

Wireless Mode

Wireless Only

Wireless Mode

XLROnly

Wireless Mode

Wireless To XLR

Un Link Wireless Really Un Link

Enter=Yes

Autres manuels pour PR5000

Table des matières

Autres manuels PR Lighting Équipement d'éclairage

PR Lighting

PR Lighting PR-8920 Manuel utilisateur

PR Lighting

PR Lighting PR-6000 FRAMING Manuel utilisateur

PR Lighting

PR Lighting PR-8121 Manuel utilisateur

PR Lighting

PR Lighting PR-111ER MOON Manuel utilisateur

PR Lighting

PR Lighting PR-2900 Manuel utilisateur

PR Lighting

PR Lighting XR250 Manuel utilisateur

PR Lighting

PR Lighting XR 1400 Framing Manuel utilisateur

PR Lighting

PR Lighting CUBIX300 Manuel utilisateur

PR Lighting

PR Lighting XR130 Beam Manuel utilisateur

PR Lighting

PR Lighting AQUA LED 1500 SPOT Manuel utilisateur

PR Lighting

PR Lighting CHAMELEON PR-2012H Manuel utilisateur

PR Lighting

PR Lighting XL WASH 700 Manuel utilisateur

PR Lighting

PR Lighting Junior JNR-8142D Manuel utilisateur

PR Lighting

PR Lighting LS150 TREE Manuel utilisateur

PR Lighting

PR Lighting Mega Colour 2500 Manuel utilisateur

PR Lighting

PR Lighting PR-2330 Manuel utilisateur

PR Lighting

PR Lighting AQUA 350 BEAM Manuel utilisateur

PR Lighting

PR Lighting TANGO FRAMING Manuel utilisateur

PR Lighting

PR Lighting PR-2203 XR 200 Manuel utilisateur

PR Lighting

PR Lighting XR 200 BEAM Mode d’emploi

PR Lighting

PR Lighting ARC LED 372 Manuel utilisateur

PR Lighting

PR Lighting AQUA 380 BEAM Manuel utilisateur

PR Lighting

PR Lighting XL 1500 Manuel utilisateur

PR Lighting

PR Lighting PR-8170A Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur