PR Lighting Mega Colour 2500 Manuel utilisateur

MEGA COLOUR 2500

PR-1255

This product manual contains important information about the safe installation and use of this

projector. Please read and follow these instructions carefully and keep this manual in a safe place

for future reference.

PR LIGHTING LTD.

http://www.pr-lighting.com

2/20

INDEX

SAFE USAGE OF THE PROJECTOR 3

INSTALLING THE PROJECTOR 4

FITTINGTHE LAMP 4

POWER SUPPLY – MAINS 5

CONTROLCONNECTIONS 5

DMXTERMINATOR 6

SETUP OPTIONS-PROJECTOR CONFIGURATION 6

TO SETTHE DMX STARTADDRESS 6

STAND-ALONE MODE 8

MASTER/SLAVE MODE 8

OPERATION MENU 9

DMX PROTOCOL 13

LED INDICATION 14

MAINTENANCE 14

KEEPING THE PROJECTOR CLEAN 14

TROUBLESHOOTING 14

TECHNICALDATA 15

ELECTRICAL DIAGRAM 17

COMPONENT ORDER CODES 18

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change without

notice. Whilst every care is taken in the preparation of this manual we reserve the right to change specifications in the course of

product improvement. The publishers cannot be held responsible for the accuracy of the information herein, or any consequence

arising from them.

Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are in good

condition before installation and use. Should there be any damage caused by transportation, consult your dealer and do not use the

unit. Any damage caused by improper use will not be assumed by the manufacturer and / or dealer.

ACCESSORIES

These items are packed together with the projector:

Name Quantity Unit Remark

Waterproof power female plug 1 Pc 3-pin 16A

XLR cable 1 Pc With plug and socket

Safety cord 4 Pcs

Fastfit clamp 4 Pcs

This manual 1 Pc

3/20

SAFE USAGE OF THE PROJECTOR

When unpacking and before disposing of the carton check there is no transportation damage before using the projector.

Should there be any damage caused by transportation, consult your dealer and do not use the apparatus.

The projector is for indoor use only, IP44. Use only in dry locations. Keep this device away from rain and moisture,

excessive heat, humidity and dust. Do not allow contact with water or any other liquids.

The projector is not designed or intended to be mounted directly on to inflammable surfaces.

The projector is only intended for installation, operation and maintenance by qualified personnel.

The projector must be installed in a location with adequate ventilation, at least 50cm from adjacent wall surfaces. Be sure

that no ventilation slots are blocked.

Do not project the beam onto inflammable surfaces, minimum distance is 10m. 10m

Avoid direct exposure to the light from the lamp. The light is harmful to the eye.

Do not attempt to dismantle and/or modify the projector in any way.

Electrical connection must only be carried out by qualified personnel.

Before installation, ensure that the voltage and frequency of power supply match the power requirements of the projector.

It is essential that each projector is correctly earthed and that electrical installation conforms to all relevant standards.

Do not connect this device to any other types of dimmer apparatus.

Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the power-cordcomeintocontact

withothercables.Only handle the power-cord by the plug. Never pull out the plug by tugging the power-cord.

Keep the lamp clean. Do not touch the lamp glass with bare hand.

The lamp used in this projector is a discharge lamp. After switching off don’t attempt to restart the projector until lamp has

cooled, this will require approx 15 minutes. Switching the lamp on and off at short intervals will reduce the life of both the

lamp and the projector. But occasional breaks will prolong the life of the lamp and projector.

Never run the projector without a lamp.

The lamp shall be changed if it has become damaged or thermally deformed.

Shields and lens shall be changed if they have become visibly damaged to such an extent than their effectiveness is

impaired, for example by cracks or deep scratches.

Exterior surface temperatures of the luminaire after 5 minutes operation is 60℃, when steady state is achieved 80℃,

During the initial start-up some smoke or smell may arise. This is a normal process and does not necessarily mean that

the device is defective.

There is no user serviceable parts inside the projector, do not open the housing and never operate the projector with the

covers removed.

Always disconnect from the mains, when the device is not in use or before cleaning it or

before attempting any maintenance work!

If you have any questions, don’t hesitate to consult your dealer or manufacturer.

4/20

INSTALLTHE PROJECTOR

HANDLE

SAFETY CORDS

CLAMP

4PCS

2PCS

CLIP

4PCS

WATERPROOF

1PC CONNECTOR

Fitted on the floor Fitted on the celling

PLUG WITH

POWER BOX

HOLE FOR

2PCS

DMX

HOLE FOR CONNECTOR

HOLE FOR

The unit was designed to make installation easy: it can be fitted on a floor, wall or ceiling as required and will

operate in any working position,

Take fastfit clamps and 4 safety cords out from the package and mount them on the underside of fixture. Hang the fixture

on the structure and fasten the screws attached to each clamp. Always ensure that the projector is firmly anchored to

avoid vibration and slipping whilst functioning. Always ensure that the structure that you are going to mount the projector

is secure and is strong enough to support a weight of MEGACOLOUR 2500.

WARNING:

1. Unlock the PAN and TILT before the 1st application of projector for safety.

2. The projector MUST be lifted or carried by the HANDLES instead of clamps.

3. For safety the safety cord should afford 10 times of the unit’s weight.

FITTING THE LAMP

Lock the yoke before fitting/replacing the lamp.

Loosen 4 clips and open the front covers.

Remove and rotate the filter module by undoing 2 M4 screws, then you will see the lamp holder and reflector.

Do not change new lamp until old lamp has cooled.

Insert the new lamp in the lamp-holder, and ensure the little bubble on the lamp is at a right angle (90°) to the beam path.

Keep the lamp clean during installation.

Fasten 2 M3 screws at the both ends of lamp.

Put back the filter module and fasten 2 M4 screws.

Close the front cover and fasten 4 clips.

5/20

POWER SUPPLY-MAINS

Connect the power cord as follows:

L(live) =brown

E (earth) =yellow/green

N (neutral) =blue

Use the plug provided to connect the mains power to the projector paying attention to the voltage and frequency marked

on the panel of the projector. It is recommended that each projector be supplied separately so that they may be

individually switched on and off.

N = NEUTRAL

3 - PIN MALE SOCKET

3 - PIN FEMALE PLUG

= GROUND

L = PHASE

IMPORTANT

It is essential that each projector is correctly earthed and the electrical installation conforms to all relevant

standards.

CONTROLCONNECTION

FUNCTION

DMX IN

DMX OUT

GND

DATA +

DATA -

DMX512

Connection between controller and projector and between one projector and another must be made with a 2

core-screened cable, with each core having at least a 0.5mm diameter. Connection to and from the projector is via

cannon 3 pin (which are included with the projector) or 5 pin XLR plugs and sockets. The XLR's are connected as shown

in the figure above.

Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. The body of

the plug is not connected in any way. The MEGA COLOUR 2500 accepts digital control signals in protocol DMX512

(1990).

Connect the controller’s output to the first fixture’s input, and connect the first fixture’s output to the second fixture’s input

and connect the rest fixtures in the same way. Eventually connect the last fixture’s output to a DMX terminator as shown

in the figure below.

No.1 No.2 No.n

DMX OUTDMX IN

DMX IN FROM TERMINATER

DMX IN DMX OUT DMX IN DMX OUT

CONTROLLER

The projector uses 3-pin XLR plug / socket. If your controller uses 5-pin XLR plug / socket, you should convert 5-pin plug

6/20

/ socket into 3-pin socket / plug as shown below.

5 PIN PLUG

Pin 1: GND (Screen)

Pin 2: Signal (data -)

Pin 3: Signal (data +)

Pin 4: N/C

Pin 5: N/C

3 PIN SOCKET

Pin 1: GND (Screen)

Pin 2: Signal (data -)

Pin 3: Signal (data +)

5 PIN SOCKET

Pin 1: GND (Screen)

Pin 2: Signal (data -)

Pin 3: Signal (data +)

Pin 4: N/C

Pin 5: N/C

3 PIN PLUG

Pin 1: GND (Screen)

Pin 2: Signal (data -)

Pin 3: Signal (data +)

DMX TERMINATOR

In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This

prevents electrical noise from disturbing and corrupting the DMX control signals.

The DMX terminator is simply an XLR connector with a 120Ω(ohm) resistor connected across pins 2 and 3, which is

then plugged into the output socket on the last projector in the chain. The connections are illustrated below.

120

DMX TERMINATOR

CONNECTION

Connect a 120 (OHM) resistor

across pins 2 and 3 in an XLR plug

and insert into the DMX out socket

on the last unit in the chain.

PIN 3

PIN 2

SETUP OPTIONS-PROJECTOR CONFIGURATION

Projector configuration can be set conveniently via pressbutton switch and LCD display. Turn the projector on and the

LCD display will show DMX address you set and save last time and it can be reset and saved again as you please.

Launch the projector. Press button ENTER more than 5 seconds to unlock panel.

Press button UP or DOWN if you want to browse through the various Setup Options. There are 10 option codes

from DMX Address to Lamp Manual Control, and each code has a specific function.

Press button ENTER to save your settings or enter the submenu.

Press button UP or DOWN to decrease / increase the numbers.

Press button FUNC will return to the previous menu one by one. If you stay for minutes the screen will return to the

default display status automatically.

TO SETTHE DMX STARTADDRESS

Each unit must be given a DMX start address so that the correct projector responds to the correct control signals. This

DMX start address is the channel number from which the projector starts to “listen” to the digital control information being

sent out from the controller. The projector have 11 channels, so set No. 1 projector’s address 001, No. 2 projector’s

address 012, No. 3 projector’s address 023, No. 4 projector’s address 034, and so on.

Launch the projector. Press button ENTER more than 5 seconds to unlock panel.

7/20

Press button ENTER to display DMX address;

Press button UP or DOWN, you can set the address;

Press button ENTER to confirm; In the same time. The GREEN LED will flash one time. It means the setting has

been enabled.

Press button FUNC, it will return to the previous menu one by one.

8/20

STAND-ALONE MODE

Operate the projector without connecting a controller, enable the master mode in the operation panel, the

projector will run in Stand-Alone mode automatically.

MASTER/SLAVE MODE

Without using a controller, many projectors can run synchronously in the Master/Slave mode by linking them

with each other. Select one projector as the master with setting options master mode enabled but slaves.

Regard the other projectors as the slaves with setting options slave mode enabled and all DMX start

address “001”.

Connect the controller’s output to the first fixture’s input, and connect the first fixture’s output to the second fixture’s input

and connect the rest fixtures in the same way. Eventually connect the last fixture’s output to a DMX terminator as shown

in the figure below.

Master

DMX OUTDMX IN

TERMINATER

DMX IN DMX OUT DMX IN DMX OUT

Slave Slave

9/20

OPERATION MENU

1st LEVEL 2nd LEVEL 3rd LEVEL 4th LEVEL 5th LEVEL 6th LEVEL

PR LIGHTING

MEGA

COLOUR

2500

DMX Address DMX Address

（001-512）

Reset Reset

Are you sure

Operation

Mode

Mode=

DMX Operation

Mode=

Master Mode

elect Memory

Preset Memory

elect Memory

Preset Memor

elect Memor

Preset Memory

elect Memory

User Memor

elect Memory

User Memor

Mode=

Salve Mode

elect Memory

Preset Memory

elect Memory

Preset Memor

elect Memor

Preset Memory

elect Memory

User Memor

elect Memory

User Memor

Mode=

Static Scene

Option

Settings

Option

Lamp Control

Lamp Control B

Power On

Lamp Control B

Control Channel

Lamp Control B

DMX Present

Option

Display Mode

Displa

OnAlwa

Displa

OffAfter Dela

Option

Display

Dimming

Disp Dim Level

Min

Disp Dim Level

10/20

Disp Dim Level

Full

Option

Pan DMX Invert

Pan DMX Inver

Option

Tilt DMX Invert

Option

Pan Tilt Swap

Pan Tilt Swa

Option

Dimmer Invert

Dimmer Inver

Option

Defaults

Restore Defaults

Information

Display

Lamp Hours Lamp Hours=

XX Reset Lamp Hours

Are You Sure?

Display

Total Hours Total Hours=XX

Display

Temperature

Display Board Display Board=

XX℃

Temperature

Drive Board Drive Board=

XX℃

Temperature

Pan Tilt Board Pan Tilt Board=

XX℃

Display

Firmware

Version

Firmware Version

Display Board Display Board=

X.X.X

Firmware Version

Drive Board Drive Board=

X.X.X

Firmware Version

Pan Tilt Board Pan Tilt Board=

X.X.X

Test Modes

Factory Setup

Off

Factory Setup

Test Modes

SelfTest

Off

SelfTest

User Memory Edit User

Memory User Memory

1 Scene XX

（1~32）

Dimmer Dimmer

XXX

CYM

Macr

(Overrides

CYM) CYM Macro

Cyan Cyan

（0~25

）

Yellow Yellow

（0~25

）

Magenta Magenta

（0~25

）

Table des matières

Autres manuels PR Lighting Équipement d'éclairage

PR Lighting

PR Lighting XR 230 Beam Manuel utilisateur

PR Lighting

PR Lighting LS150 TREE Manuel utilisateur

PR Lighting

PR Lighting PR-8120 Manuel utilisateur

PR Lighting

PR Lighting AQUA LED 1500 SPOT Manuel utilisateur

PR Lighting

PR Lighting XR250 Manuel utilisateur

PR Lighting

PR Lighting TANGO FRAMING Manuel utilisateur

PR Lighting

PR Lighting DESIGN 150 Manuel utilisateur

PR Lighting

PR Lighting PR-2001L Manuel utilisateur

PR Lighting

PR Lighting PR-8170A Manuel utilisateur

PR Lighting

PR Lighting CUBIX300 Manuel utilisateur

PR Lighting

PR Lighting PR5000 Manuel utilisateur

PR Lighting

PR Lighting ARC LED 372 Manuel utilisateur

PR Lighting

PR Lighting PR-8835 Manuel utilisateur

PR Lighting

PR Lighting XR130 Beam Manuel utilisateur

PR Lighting

PR Lighting AQUA 380 BEAM Manuel utilisateur

PR Lighting

PR Lighting XR 380 BWS Manuel utilisateur

PR Lighting

PR Lighting XLED 4007 BEAM Manuel utilisateur

PR Lighting

PR Lighting XPar 150 Zoom Manuel utilisateur

PR Lighting

PR Lighting AQUA 580 BWS Manuel utilisateur

PR Lighting

PR Lighting Junior JNR-8142D Manuel utilisateur

PR Lighting

PR Lighting XL 1500 Manuel utilisateur

PR Lighting

PR Lighting PR-111ER MOON Manuel utilisateur

PR Lighting

PR Lighting AQUA 380 BWS Manuel utilisateur

PR Lighting

PR Lighting PR-8920 Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur