PR Lighting PR-2330 Manuel utilisateur

XL Beam 300

PR-2330/2330M

This product manual contains important information about the safe installation and use of this

projector. Please read and follow these instructions carefully and keep this manual in a safe place

for future reference.

PR LIGHTING LTD.

http://www.pr-lighting.com

2/26

INDEX

SAFE USAGE OF THE PROJECTOR 3

INSTALLING THE PROJECTOR 4

FITTING THE LAMP 4

POWER SUPPLY – MAINS 5

CONTROL CONNECTIONS 5

DMX TERMINATOR 6

SETUP OPTIONS-PROJECTOR CONFIGURATION 6

TO SET THE DMX START ADDRESS 6

MASTER/SLAVE MODE 7

STAND-ALONE MODE 7

OPERATION MENU 8

ERROR MESSAGES 12

REPLACING GOBOS 12

DMX PROTOCOL 13

LED INDICATION 16

MAINTENANCE 16

LUBRICATION 16

KEEPING THE PROJECTOR CLEAN 16

TROUBLESHOOTING 17

TECHNICAL DATA 18

ELECTRICAL DIAGRAM 22

COMPONENT ORDER CODES 24

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change without

notice. Whilst every care is taken in the preparation of this manual we reserve the right to change specifications in the course of

product improvement. The publishers cannot be held responsible for the accuracy of the information herein, or any consequence

arising from them.

Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are in good

condition before installation and use. Should there be any damage caused by transportation, consult your dealer and do not use the

unit. Any damage caused by improper use will not be assumed by the manufacturer and / or dealer.

ACCESSORIES

These items are packed together with the projector:

Name Quantity Unit Remark

G clamps 2 Pcs

3-pin XLR connector 1 Set Without cable

Safety cord 1 Pc

This manual 1 Pc

Ωclamps 2 Pcs Options

3/26

SAFE USAGE OF THE PROJECTOR

When unpacking and before disposing of the carton check there is no transportation damage before using the projector.

Should there be any damage caused by transportation, consult your dealer and do not use the apparatus.

The projector is for indoor use only, IP20. Use only in dry locations. Keep this device away from rain and moisture,

excessive heat, humidity and dust. Do not allow contact with water or any other liquids.

The projector is not designed or intended to be mounted directly on to inflammable surfaces.

The projector is only intended for installation, operation and maintenance by qualified personnel.

The projector must be installed in a location with adequate ventilation, at least 50cm from adjacent wall surfaces. Be sure

that no ventilation slots are blocked.

Do not project the beam onto inflammable surfaces, minimum distance is 5m. 5m

Avoid direct exposure to the light from the lamp. The light is harmful to the eye.

Do not attempt to dismantle and/or modify the projector in any way.

Electrical connection must only be carried out by qualified personnel.

Before installation, ensure that the voltage and frequency of power supply match the power requirements of the projector.

It is essential that each projector is correctly earthed and that electrical installation conforms to all relevant standards.

Do not connect this device to any other types of dimmer apparatus.

Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the power-cord come into contact

with other cables. Only handle the power-cord by the plug. Never pull out the plug by tugging the power-cord.

Keep the lamp clean. Do not touch the lamp glass with bare hand.

The projector should always be installed with a secondary safety fixing. A safety cord is supplied for this; it should be

attached as shown in “installing the projector” section.

The lamp used in this projector is a discharge lamp. After switching off don’t attempt to restart the projector until lamp has

cooled, this will require approx 15 minutes. Switching the lamp on and off at short intervals will reduce the life of both the

lamp and the projector. But occasional breaks will prolong the life of the lamp and projector.

Never run the projector without a lamp.

The lamp shall be changed if it has become damaged or thermally deformed.

Shields and lens shall be changed if they have become visibly damaged to such an extent than their effectiveness is

impaired, for example by cracks or deep scratches.

Exterior surface temperatures of the luminaire after 5 minutes operation is 40℃, when steady state is achieved 50℃,

There is no user serviceable parts inside the projector, do not open the housing and never operate the projector with the

covers removed.

Always disconnect from the mains, when the device is not in use or before cleaning it or

before attempting any maintenance work !

If you have any questions, don’t hesitate to consult your dealer or manufacturer.

4/26

INSTALL THE PROJECTOR

Take 2 clamps and the safety cord out from the package and mount 2 clamps on the underside of fixture with 2 retainers

attached to each clamp. Hang the fixture on the structure and fasten the screws attached to each clamp. (See the

WARNING on the underside of the base as shown above) To pass the SAFETY CORD through 2 HOLES for safety!

Always ensure that the projector is firmly anchored to avoid vibration and slipping whilst functioning. Always ensure that

the structure that you are going to mount the projector to is secure and is strong enough to support a weight of XL Beam

300.

WARNING:

1. Unlock the PAN and TILT before the 1st application of projector for safety.

2. The projector MUST be lifted or carried by the HANDLES instead of clamps.

3. For safety the safety cord should afford 10 times of the unit’s weight.

FITTING THE LAMP

Lock the yoke before fitting/replacing the lamp.

Open the cover board at the rear of the projector by loosening 3 screws, you can see the structure as shown in the figure

above.

Gently pull out the lamp holder assembly.

Take out the worn-out lamp. Insert the new lamp to the socket. Note: don’t touch the bulb of the new lamp with bare

hands so as not to influence the beam output.

Close the rear cover and fasten 3 screws.

WARNING: The MSD series are high-pressure lamps with external igniters ( ). Care should always be taken

when handling these lamps.Always read the manufacturers "Instructions for use" enclosed with the lamp.

5/26

POWER SUPPLY-MAINS

Connect the power cord as follows:

L (live) =brown

E (earth) =yellow/green

N (neutral) =blue

Use the plug provided to connect the mains power to the projector paying attention to the voltage and frequency marked

on the panel of the projector. It is recommended that each projector be supplied separately so that they may be

individually switched on and off.

IMPORTANT

It is essential that each projector is correctly earthed and the electrical installation conforms to all relevant

standards.

CONTROL CONNECTION

Connection between controller and projector and between one projector and another must be made with a 2

core-screened cable, with each core having at least a 0.5mm diameter. Connection to and from the projector is via

cannon 3 pin (which are included with the projector) or 5 pin XLR plugs and sockets. The XLR's are connected as shown

in the figure above.

Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. The body of

the plug is not connected in any way. The XL Beam 300 accepts digital control signals in protocol DMX512 (1990).

Connect the controller’s output to the first fixture’s input, and connect the first fixture’s output to the second fixture’s input

and connect the rest fixtures in the same way. Eventually connect the last fixture’s output to a DMX terminator as shown

in the figure below.

6/26

DMX TERMINATOR

In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This

prevents electrical noise from disturbing and corrupting the DMX control signals.

The DMX terminator is simply an XLR connector with a 120Ω(ohm) resistor connected across pins 2 and 3, which is

then plugged into the output socket on the last projector in the chain. The connections are illustrated below.

120

DMX TERMINATOR

CONNECTION

Connect a 120 (OHM) resistor

across pins 2 and 3 in an XLR plug

and insert into the DMX out socket

on the last unit in the chain.

PIN 3

PIN 2

SETUP OPTIONS-PROJECTOR CONFIGURATION

Projector configuration can be set conveniently via pressbutton switch and LCD display. Turn the projector on and the

LCD display will show DMX address you set and saved last time and it can be reset and saved again as you please.

Launch the projector and press button ENTER for more than 5 seconds to unlock the panel, the LCD will show the

function menu of the projector, each main menu has its submenus and each submenu has a specific function. For

details, please see the “OPERATION MENU” section.

Press button UP or DOWN if you want to browse through the various Setup Options. Press button ENTER to save your

settings or enter the next menu.

Press button UP or DOWN to shift.

Press button FUNC, it will return to the upper menu one by one. If you stay for minutes defaulted will show display status

automatically.

TO SET THE DMX START ADDRESS

Each XL Beam 300 must be given a DMX start address so that the correct projector responds to the correct control

signals. This DMX start address is the channel number from which the projector starts to “listen” to the digital control

information being sent out from the controller. The XL Beam 300 has 3 DMX modes. There are standard mode,

extended mode and short mode. For example standard mode has 19 channels, so set the No. 1 projector’s address 001,

No. 2 projector’s address 020, No. 3 projector’s address 039, No. 4 projector’s address 058, and so on.

Launch the projector. Press button ENTER more than 5 seconds to unlock panel.

Press button FUNC to display DMX address;

7/26

Press button UP and DOWN, you can set the address;

Press button ENTER to confirm; In the same time. The GREEN LED will flash one time. It means the setting has

been enabled.

Press button FUNC, it will return to the upper menu one by one.

STAND-ALONE MODE

Operate the projector without connecting a controller, enable the master mode in the operation panel, the

projector will run in Stand-Alone mode automatically.

MASTER/SLAVE MODE

Without using a controller, many projectors can run synchronously in the Master/Slave mode by linking them

with each other. Select one projector as the master with setting options master mode enabled but slaves.

Regard the other projectors as the slaves with setting options slave mode enabled and all DMX start

address “001”.

Connect the controller’s output to the first fixture’s input, and connect the first fixture’s output to the second fixture’s input

and connect the rest fixtures in the same way. Eventually connect the last fixture’s output to a DMX terminator as shown

in the figure below.

8/26

OPERATION MENU

1st LEVEL 2nd LEVEL 3rd LEVEL 4th LEVEL 5th LEVEL 6th LEVEL

PR LIGHTING

SERIES

XL BEAM 300

PR LIGHTING

DMX Address

PR LIGHTING

DMX Address

XXX

PR LIGHTING

Reset

PR LIGHTING

Reset

Are you sure

PR LIGHTING

Config Settings

PR LIGHTING

DMX Mode

PR LIGHTING

DMX Mode

Standard

PR LIGHTING

DMX Mode

Extended

PR LIGHTING

DMX Mode

Short

PR LIGHTING

Loss of DMX

PR LIGHTING

When DMX is Lost

Normal Time Out

PR LIGHTING

When DMX is Lost

Hold Last Value

PR LIGHTING

Lamp Control

PR LIGHTING

Lamp Control By

Control Channel

PR LIGHTING

Lamp Control By

Power On

PR LIGHTING

Lamp Control By

DMX Present

PR LIGHTING

Option Settings

PR LIGHTING

Colour Positions

PR LIGHTING

Colour Positions

STEPPED

PR LIGHTING

Colour Positions

LINEAR

PR LIGHTING

Pan DMX Invert

PR LIGHTING

Pan DMX Invert

OFF

PR LIGHTING

Pan DMX Invert

PR LIGHTING

Tilt DMX Invert

PR LIGHTING

Tilt DMX Invert

OFF

PR LIGHTING

Tilt DMX Invert

PR LIGHTING

Pan Tilt Swap

PR LIGHTING

Pan Tilt Swap

OFF

PR LIGHTING

Pan Tilt Swap

PR LIGHTING

Dimmer Invert

PR LIGHTING

Dimmer Invert

OFF

PR LIGHTING

Dimmer Invert

9/26

PR LIGHTING

Iris Invert

PR LIGHTING

Iris Invert

OFF

PR LIGHTING

Iris Invert

PR LIGHTING

Zoom Invert

PR LIGHTING

Zoom Invert

OFF

PR LIGHTING

Zoom Invert

PR LIGHTING

CYM Invert

PR LIGHTING

CYM Invert

OFF

PR LIGHTING

CYM Invert

PR LIGHTING

Defaults

PR LIGHTING

Defaults

OFF

PR LIGHTING

Defaults

Restore Defaults

PR LIGHTING

Display Options

PR LIGHTING

Display Mode

PR LIGHTING

Display Mode

On Always

PR LIGHTING

Display Mode

Off After Delay

PR LIGHTING

Display Invert

PR LIGHTING

Display Invert

OFF

PR LIGHTING

Display Invert

PR LIGHTING

Display Dimming

PR LIGHTING

Disp Dim Level

XXX(Min,1~9,Full),

Default is 8)

PR LIGHTING

Display Contrast

PR LIGHTING

Display Contrast

XX(0~20, Default

is 10)

PR LIGHTING

Information

PR LIGHTING

Lamp Hours

PR LIGHTING

Lamp Hours=

PR LIGHTING

Reset Lamp Hours

Are You Sure?

PR LIGHTING

Total Hours

PR LIGHTING

Total Hours=XX

PR LIGHTING

Temperature

PR LIGHTING

Driver Board

PR LIGHTING

Driver Board=

XX℃

PR LIGHTING

Head Sensor

PR LIGHTING

Head Sensor=

XX ℃

PR LIGHTING

Software Version

PR LIGHTING

Display Board

PR LIGHTING

Display Board=

X.X.X

PR LIGHTING

View DMX Values

PR LIGHTING

DMX Channel

1=0

PR LIGHTING

Electronic SN

PR LIGHTING

Electronic SN=

=************

PR LIGHTING

Test Modes

PR LIGHTING

Factory Setup

PR LIGHTING

Factory Setup

OFF

PR LIGHTING

10/26

Factory Setup

PR LIGHTING

Self Test

PR LIGHTING

Self Test

OFF

PR LIGHTING

Self Test

PR LIGHTING

Lamp Manual

Control

PR LIGHTING

Lamp Status

PR LIGHTING

Status = XX

Control = XX

PR LIGHTING

Turn Lamp On

PR LIGHTING

Turn Lamp Off

PR LIGHTING

Operation Mode

PR LIGHTING

Operation Mode=

DMX Operation

PR LIGHTING

Operation Mode=

Master Mode

PR LIGHTING

Select Memory

User Memory 1

PR LIGHTING

Select Memory

User Memory 2

PR LIGHTING

Select Memory

Preset Memory

PR LIGHTING

Select Memory

Preset Memory 2

PR LIGHTING

Select Memory

Preset Memory

PR LIGHTING

Operation Mode=

Slave Mode

PR LIGHTING

Select Memory

User Memory 1

PR LIGHTING

Select Memory

User Memory 2

PR LIGHTING

Select Memory

Preset Memory

PR LIGHTING

Select Memory

Preset Memory 2

PR LIGHTING

Select Memory

Preset Memory

PR LIGHTING

Mode=

Static Scene

PR LIGHTING

User Memories

PR LIGHTING

Edit User Memory

PR LIGHTING

User Memory 1

PR LIGHTING

Scene XX

（1~28）

PR LIGHTING

Shutter

PR LIGHTING

Shutter

XXX

PR LIGHTING

Dimmer

PR LIGHTING

Dimmer

XXX

PR LIGHTING

CYM Macro

PR LIGHTING

CYM Macro

XXX

PR LIGHTING

Cyan

PR LIGHTING

Cyan

XXX

PR LIGHTING

Yellow

PR LIGHTING

Yellow

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels PR Lighting Équipement d'éclairage

PR Lighting

PR Lighting XLED 4007 BEAM Manuel utilisateur

PR Lighting

PR Lighting PR5000 Manuel utilisateur

PR Lighting

PR Lighting XPar 360 Manuel utilisateur

PR Lighting

PR Lighting PR-2203 XR 200 Manuel utilisateur

PR Lighting

PR Lighting XL 1500 Manuel utilisateur

PR Lighting

PR Lighting TANGO FRAMING Manuel utilisateur

PR Lighting

PR Lighting XR 380 BWS Manuel utilisateur

PR Lighting

PR Lighting AQUA 380 BEAM Manuel utilisateur

PR Lighting

PR Lighting CUBIX300 Manuel utilisateur

PR Lighting

PR Lighting XR130 Beam Manuel utilisateur

PR Lighting

PR Lighting PR-111ER MOON Manuel utilisateur

PR Lighting

PR Lighting PR-2900 Manuel utilisateur

PR Lighting

PR Lighting XLED 590 Manuel utilisateur

PR Lighting

PR Lighting PR-8170A Manuel utilisateur

PR Lighting

PR Lighting CHAMELEON PR-2012H Manuel utilisateur

PR Lighting

PR Lighting LS150 TREE Manuel utilisateur

PR Lighting

PR Lighting AQUA 380 BWS Manuel utilisateur

PR Lighting

PR Lighting ARC LED 372 Manuel utilisateur

PR Lighting

PR Lighting XR 200 BEAM Mode d’emploi

PR Lighting

PR Lighting PR-8836 Manuel utilisateur

PR Lighting

PR Lighting AQUA 350 BEAM Manuel utilisateur

PR Lighting

PR Lighting XPar 150 Zoom Manuel utilisateur

PR Lighting

PR Lighting PR-8835 Manuel utilisateur

PR Lighting

PR Lighting XL WASH 700 Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur