powersoft DigiMod 1000 NPS Guide de sécurité
powersoft_connecting_dm1000nps_to_500_1000_1000IS_en_v1.0
© 2012 Powersoft
Powersoft S.r.l. • Via Enrico Conti, 5 • 50018 Scandicci (FI) • Italy
+39 055 735 0230 • sales@powersoft.it • www.powersoft-audio.com
How To Connect a DigiMod
1000NPS to a DigiMod
500/1000/1000 IS
1 Introduction
1.1 Preliminary considerations
The DigiMod 1000NPS is an exact replica of the DigiMod 1000 output stage (2-channel bridgeable, 2x500W on 4Ω, 1x1000W on 8Ω),
which can be used in combination with DigiMod 500/1000/1000 IS to extend the range of possible multi-channel congurations and power
3-way active loudspeakers. In order to make this connection possible, the DigiMod 1000NPS must be equipped with an optional DSP-C
board.
Related Products:
▶DigiMod 1000NPS*
▶DigiMod 500
▶DigiMod 1000
▶DigiMod 1000 IS
* with DSP
1.2 Tools Needed:
▶1 male MOLEX 3-pin connector
▶1 female MOLEX 3-pin connector
▶1 male PHOENIX 5-pin connector (MSTB, 2.5/5-ST-5.08)
▶Balanced cable (low impedance)
▶Soldering iron and solder
▶Powersoft CB000098 cable or equivalent (10 pole 8/10 mm cable, with 2 MOLEX Micro-Fit 3.0 connectors)
▶pliers for electronic use
2 Procedure
2.1 Connect the Power supply
FIGURE 1: DigiMod 500 power supply connector position
▶2
How To Connect a DigiMod 1000NPS to a DigiMod 500
FIGURE 2: DigiMod 1000 power supply connector position
FIGURE 3: DigiMod 1000 IS power supply connector position
Use the CB000098 Powersoft cable to connect the DigiMod 500/1000/1000 IS power supply to the DigiMod1000NPS.
FIGURE 4: The DigiMod 1000NPS power supply connector
2.2 Master or Slave
Powersoft recommends using the module with a DSP on board as master module, while the module without a DSP should be used as a
slave1. In this particular case, the DigiMod 1000NPS will act as master module with its on board DSP, while the DigiMod 500/1000 will be
the slave module. DigiMod 1000 IS modules come equipped with a DSP board that must be removed in order to congure the module as
a slave module.
The onboard DSP has 4 outputs:
Channels 1 and 2 output directly from the DSP board. These two channels could be used, for example, to drive the rst two ways of a three
way system.
Channels 3 and 4 are used to carry the input signal over to the DigiMod 500/1000/1000 IS slave module through a MOLEX connector on
the DSP board itself. The DigiMod 500/1000/1000 IS will therefore receive channels 3 and 4 as input. In this conguration, the slave module’s
1Please note that this conguration is compatible with all presets Powersoft makes available to the public. Any other conguration is not guaranteed as compatible with Powersoft presets.
▶3
How To Connect a DigiMod 1000NPS to a DigiMod 500
output can be used, for example, in a bridged conguration to drive a subwoofer requiring more power.
2.3 How To Set Master And Slave Modules
Locate the jumpers on the modules
To set the module with DSP as MASTER: remove the jumpers in the pins BY22-BY33 in CN18 and BY31-BY21 in CN17 (the innermost
jumpers). Use pliers to aid in the removal (see Section FIGURE 5)
To set the other module (the one without DSP) as SLAVE: leave the jumper conguration as factory set.
FIGURE 5: Jumpers for setting a module as master or slave
3.3 Connecting the DigiMod 1000NPS To The DigiMod 500/1000/1000 IS
In order to connect the master module’s output channels (DigiMod 1000NPS) 3 and 4 from the DSP so they become inputs for the DigiMod
500/1000/1000 IS:
1. Remove the DSP from the DigiMod 1000NPS module
2. Take the male MOLEX 3-pin connector and solder this connector in the DSP board as seen in the picture below2
2Some DSP modules are equipped with a MOLEX connector at production time
▶4
How To Connect a DigiMod 1000NPS to a DigiMod 500
FIGURE 6: DSP with soldered MOLEX connector and three pin male MOLEX connector
3. Make the following cable so it connects DSP output channels 3 and 4 from the MOLEX connector to the DigiMod 1000NPS Phoenix
inputs. The cable will be balanced, low impedance and will have the following connectors:
▶1 3-pin female MOLEX
▶2 5-pin male Phoenix
4. Use the gure below as a connector pin soldering diagram.
FIGURE 7: Connector pin diagram
5-pin male Phoenix
Pin 1: GND
PIn 2: Hot Pole
Pin 3: Cold Pole
Pins 4 & 5: unused
3-pin female MOLEX connector:
Pin 1: Cold pole
Pin 2: GND
Pin 3: Hot pole
▶5
How To Connect a DigiMod 1000NPS to a DigiMod 500
In case of ground loop problems, remove the GND wire connection in the cable.
In order to connect the master module outputs to the slave module inputs:
1. Connect the cable that you’ve just made to the DSP in the DigiMod 1000NPS master module (with the MOLEX 3-pin connector).
2. Connect the other end of the cable with its two Phoenix 5-pin connectors to the slave module’s input connectors as seen in the gure
below:
FIGURE 8: DigiMod 500 Phoenix input connector
FIGURE 9: DigiMod 1000 Phoenix input connector (DigiMod 1000 IS is identical)
Ce manuel convient aux modèles suivants
3
Table des matières
Autres manuels powersoft Unité de contrôle
powersoft
powersoft IpalMod Manuel utilisateur
powersoft
powersoft LiteMod 4HC Manuel utilisateur
powersoft
powersoft DigiMod IS Series Fiche technique
powersoft
powersoft M-Drive Series Manuel utilisateur
powersoft
powersoft DigiMod 3004PFC2 Manuel utilisateur
powersoft
powersoft DigiMod 500 Manuel utilisateur
powersoft
powersoft DigiMod IS integration kit Mode d’emploi
powersoft
powersoft DigiMod 3004PFC4 Manuel utilisateur
powersoft
powersoft LiteMod 4HC Manuel utilisateur
powersoft
powersoft IpalMod Manuel utilisateur
Manuels Unité de contrôle populaires d'autres marques
Festo
Festo Compact Performance CP-FB6-E Manuel de la liste des pièces
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur
JS Automation
JS Automation MPC3034A Manuel utilisateur
JAUDT
JAUDT SW GII 6406 Series Guide rapide
Spektrum
Spektrum Air Module System Manuel utilisateur
BOC Edwards
BOC Edwards Q Series Manuel utilisateur
