POSIFLEX RT-1016A-G2 Manuel utilisateur

Package Contents

RT-1016A-G2 15.6” fanless touch terminal (x 1)

Power adapter (x 1)

Power cord (x 1)

User manual (x 1)

FCC NOTES

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the user will be required to correct

the interference at his own expense.

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

CE CLASS A WARNING

This equipment is compliant with Class A of CISPR 32. In a residential environment this

equipment may cause radio interference.

AVERTISSEMENT CE CLASSE A

Cet équipement est conforme àla classe A de CISPR 32. Dans un environnement résidentiel,

cet équipement peut provoquer des interférences radio.

WARRANTY LIMITS

Warranty will terminate automatically when the machine is opened by any person other than

the authorized technicians. The user should consult his/her dealer for the problem happening.

Warranty voids if the user does not follow the instructions in application of this merchandise.

The manufacturer is by no means responsible for any damage or hazard caused by improper

application.

LIMITES DE GARANTIE

La garantie prend fin automatiquement lorsque la machine est ouverte par une personne autre

que les techniciens autorisés. L'utilisateur doit consulter son revendeur pour le problème qui

se produit. La garantie s'annule si l'utilisateur ne suit pas les instructions d'application de

cette marchandise. Le fabricant n'est en aucun cas responsable de tout dommage ou danger

causé par une mauvaise application.

RT-1016A-G2

Fanless Touch POS Terminal

User Manual

16950908010 Ver. A0

http://www.posiflex.com

警告使用者

此為甲類資訊技術設備，於居住環境中使用時，可能會造成射頻擾動，在此種情況

下，使用者會被要求採取某些適當的對策。

SAFETY INSTRUCTIONS

Never open the equipment. For safety reasons, the equipment should be opened and installed

only by qualified skilled person. The power outlet socket must be located near the equipment

and must be easily accessible.

CONSIGNES DE SÉCURITÉ

Cet équipement ne convient pas àune utilisation dans des lieux pouvant accueillir des

enfants.

WARNING

Power cord shall be connected to a socket-outlet with earthing connection.

ATTENTION

Le cordon d'alimentation doit être connecté à une prise de courant avec mise à la terre.

BATTERY WARNING

Risk of explosion if battery is replaced by an incorrect type. Dispose of expended battery in

accordance with local disposal regulations.

AVERTISSEMENT DE BATTERIE

Risque d'explosion si la batterie est remplacée par un type incorrect. Jetez la batterie

usagée conformément aux réglementations locales en matière d'élimination.

警告

本電池如果更換不正確會有爆炸的危險，請依製造商說明書處理用過之電池。

Views of RT-1016A-G2

Front View

Rear View

Bottom View

System Back Cover

Stand Cover

Cable Exit

Attachment Bay

Release Lever for System Back Cover

Screw for Fire-Resistant

System Back Cover

LED indicator

P-Cap Touch

Panel

Camera (Optional)

Left-Side View

Views of RB-5000 UPS Base Stand (Option for RT Series Model)

Top View Bottom View

When the AC power is turned off, the RT terminal will begin to be

three seconds. At this time, back up the data on the terminal

immediately and power off the RT terminal.

When the AC power is turned off, if the UPS battery is very low, the

RB-5000 will beep once every second. At this moment, power off the

RT terminal immediately.

To get more detailed information of RB-5000, please contact the service team

of Posiflex or download the RB-5000 user manual from Posiflex Global

Website: (http://www.posiflex.com/en-global/Download/download).

Power Button

Brightness Adjustment Button ＋

Brightness Adjustment Button －

BATT.

DC OUT

DC IN

Rubber Foot

Battery Cable

Screw Hole

Through Hole

View of I/O Interface of RT-1016A-G2

Bottom Side View

Side View

Positioning your POS for a Perfect Viewing Angle

Steady the base with one hand, and then tilt the screen

in the direction shown by the arrow in the figure.

Please do NOT press on the LCD panel while

setting up the tilt angle.

Installing Power Adapter and Cables

The following provides instructions required to install your cables.

1. Lay the terminal with its rear facing

towards you and tilt the screen all the way

down.

USB 3.0 Port

DB9 COM Port

CR Port

LAN Port

DC IN

Power

Connector

Micro USB OTG

RJ50 COM Ports

USB 2.0 Port

Micro SD Card Slot

HDMI Port

2. Remove the system back cover.

2.1 If the system back cover is fire-resistant, first locate the screw as

indicated in the figure, and then remove it.

2.2 Hold down the release lever at the bottom of

the system back cover and then pulling the

cover outwards.

3. To remove the stand cover from the base, grab the top side of the

cover, (1) lift the stand cover up gently, (2) pull it at a 45 degree

angle, and then (3) slide it in the horizontal direction shown by the

arrow.

4. Connect the connector of the power adapter

to the DC-IN power jack. If necessary,

properly insert other cables into the correct

port.

Screw for Fire-Resistant

System Back Cover

5. Neatly arrange the cables. Locate the cable holder inside the base as

shown in the figure. Push down the lever to release if from the hook,

pass the cable through cable holder, and then press down the lever

again to lock it onto the hook.

6. Make sure the cord can be held into place

and passed through the cable exit after

sliding back the stand cover.

7.1 Place back the sytem back cover. Make sure

it is well locked into place with a click sound.

7.2 For the fire-resistant system back cover, please insert another

screw into the screw hole indicated in the figure, and secure it.

8. Make sure the cable could be pulled out of

the cable exit from the bottom of the base.

Cable holder

Screw for Fire-Resistant

System Back Cover

Cable connectors like the connector of LAN cable have to be gently inserted

until a click sound is given. It is recommended that the I/O ports, such as COM

(DB9) port and VGA port, should be fastened with connector thumb screws

after the I/O cable connectors are completely connected. And please make sure

that each connector has to be connected to the right peripheral device in the

right way.

CAUTION: On doing insertion or extraction of a cable connector, please always

hold the connector head itself instead of pulling the cable wire. Doing this could

damage the cables, which is considered as an artificial damage and is not covered

by the warranty. The means of power cord should be connected to a socket-outlet

with earthing connection.

ATTENTION: Lors de l'insertion ou de l'extraction d'un connecteur de câble,

veuillez toujours tenir la tête du connecteur elle-même au lieu de tirer le fil du

câble. Cela pourrait endommager les câbles, ce qui est considérécomme un

dommage artificiel et n'est pas couvert par la garantie. Le cordon d'alimentation

doit être connecté à une prise de courant avec mise à la terre.

Installing Optional Upgrade Kits and Peripherals

RT-1016A-G2 is an expandable model which allows you to upgrade its own

capacity by additionally installing multiple peripheral devices, such as

magnetic stripe reader (MSR), fingerprint or iButton sensors, and 2nd rear-

mount POS monitor, according to your preference. The following will give

you brief instructions on how to expand on your current POS system with

these optional upgrade kits. Before proceeding with the installation of

peripherals, please make sure the POS system is completely shut down to

prevent damage.

Installing Side Mount Upgrade Kits

Located at left side on the back of your system

unit, side mount compartment is mainly used for

installation of side-mounted equipment, such as

magnetic stripe reader. For detailed installation

instructions, please refer to the user manual

specific to the device which you intend to

mount onto the terminal.

Installing Rear-Mount POS Monitor

RT-series POS terminal also allows you to additionally

install rear-mount POS monitor to expand its

functionality. Regarding the step-by-step instructions

which aim to help you mount it onto your POS system,

Please refer to the user manual specific to the device you

intend to install.

Installing PoweredUSB or USB Hub

Please go through the below steps to complete the installation of

PoweredUSB or USB hub.

1. After tilting the screen all the way down, remove the system back

cover.

1.1 If the system back cover is fire-resistant, first locate the

screw as indicated in the figure, and then remove it.

1.2 Hold down the release lever at the

bottom of the system back cover and

then pulling the cover outwards

2. To remove the stand cover from the base, grab the top side of the

cover, (1) lift the stand cover up gently, (2) pull it at a 45 degree

angle, and then (3) slide it in the horizontal direction shown by the

arrow.

Screw for Fire-Resistant

System Back Cover

3. Align the two screw bolts at the bottom of PoweredUSB or USB hub

with rail slots in the base.

Push PoweredUSB or USB hub in the

direction shown by the arrow to lock it

into place.

To remove the PoweredUSB or USB hub from the rail slots, press

down the hubs first and then push it outwards.

5. Install power adaptor extension cable, USB cable, and power adaptor

for PoweredUSB hub.

5.1 Insert one end of the provided power

adaptor extension cable to DC Input port

of PoweredUSB hub and another end to

DC-in power jack of the terminal.

5.2 Insert mini-USB connector of the USB

cable to PoweredUSB hub and another

end to USB3.0 port of the terminal.

5.3 Connect the connector of the power

adapter to DC Output port of

PoweredUSB hub, and the other end to the

electrical outlet.

Table des matières

Autres manuels POSIFLEX Terminal tactile

POSIFLEX

POSIFLEX XT-2614E Manuel utilisateur

POSIFLEX

POSIFLEX XT-3817 Manuel utilisateur

POSIFLEX

POSIFLEX XT-6015C Manuel utilisateur

POSIFLEX

POSIFLEX XT-3817-G2 Manuel utilisateur

POSIFLEX

POSIFLEX MT-4310W/R Manuel utilisateur

POSIFLEX

POSIFLEX Jiva TP-5815 Pro series Manuel utilisateur

POSIFLEX

POSIFLEX HT-3200 SERIES Manuel utilisateur

POSIFLEX

POSIFLEX PS-3315 Manuel utilisateur

POSIFLEX

POSIFLEX KS-7410 Manuel utilisateur

POSIFLEX

POSIFLEX KS - 6910 series Manuel utilisateur

POSIFLEX

POSIFLEX XT-4015-G2 Manuel utilisateur

POSIFLEX

POSIFLEX XT-3015 Manuel utilisateur

POSIFLEX

POSIFLEX PST-6000 SERIES Manuel utilisateur

POSIFLEX

POSIFLEX XP-2000 Series Manuel utilisateur

POSIFLEX

POSIFLEX XT-4015 Manuel utilisateur

POSIFLEX

POSIFLEX SA-304 Manuel utilisateur

POSIFLEX

POSIFLEX XT-3615 Manuel utilisateur

POSIFLEX

POSIFLEX DT-207 series Manuel utilisateur

POSIFLEX

POSIFLEX RT-2015E Manuel utilisateur

POSIFLEX

POSIFLEX XT-5315 Manuel utilisateur

POSIFLEX

POSIFLEX HS-66 W Series Manuel utilisateur

POSIFLEX

POSIFLEX PST-7000 Series Manuel utilisateur

POSIFLEX

POSIFLEX KS-6115 Manuel utilisateur

POSIFLEX

POSIFLEX KS - 6810 Manuel utilisateur

Manuels Terminal tactile populaires d'autres marques

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Manuel utilisateur

Ingenico

Ingenico AXIUM EX4000 Manuel utilisateur

Heisei Electronics

Heisei Electronics Q-POS 815 Manuel utilisateur

Amano

Amano MTX-15 Manuel utilisateur

FLOWBIRD

FLOWBIRD CWT Compact Touch Manuel utilisateur

Demco

Demco SP7 Manuel utilisateur

Lathem

Lathem PC600 Series Manuel utilisateur

Partner

Partner MF-2352 Manuel utilisateur

NCR

NCR RealPOS 7460-2 Manuel

Simrad

Simrad MS50 Instructions de montage

Unitech

Unitech MR350 MKII Guide de démarrage rapide

Jungheinrich

Jungheinrich WMT 210 Manuel utilisateur

Motorola

Motorola MTP850 Manuel utilisateur

YASKAWA

YASKAWA 62H-MDC0 Manuel utilisateur

MVG industries

MVG industries NeptuLink Manuel utilisateur

Price Industries Limited

Price Industries Limited FDC Manuel d'instructions

Honeywell

Honeywell TemaKey Manuel utilisateur

EBN

EBN BPC65-B-A16G Manuel utilisateur