POSIFLEX PS-3416 Manuel utilisateur
1
Package Contents
Fanless LCD touch terminal (x1)
Power adaptor (x1)
Power cord (x1)
User Manual (x1)
Recovery DVD (x1)
(for pre-loaded OS model only)
FCC NOTES
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct
the interference at his own expense.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
CE CLASS A WARNING
This equipment is compliant with Class A of CISPR 32. In a residential environment this
equipment may cause radio interference.
WARRANTY LIMITS
Warranty will terminate automatically when the machine is opened by any person other than
the authorized technicians. The user should consult his/her dealer for the problem happening.
Warranty voids if the user does not follow the instructions in application of this merchandise.
The manufacturer is by no means responsible for any damage or hazard caused by improper
application.
警告使用者
此為甲類資訊技術設備，於居住環境中使用時，可能會造成射頻擾動，在此種情況
下，使用者會被要求採取某些適當的對策。
SAFETY INSTRUCTIONS
This equipment is not suitable for use in locations where children are likely to be present.
PS-3416/3416E
Fanless LCD Touch Terminal
User Manual
13120901030 Ver. C0
2
CONSIGNES DE SÉCURITÉ
Cet équipement ne convient pas à une utilisation dans des lieux pouvant accueillir des
enfants.
BATTERY CAUTION NOTES
Dispose of used batteries according to the instructions.
Replacement of a battery with an incorrect type that can defeat a safeguard (for
example, in the case of some lithium battery types)
Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a
battery that can result in an explosion.
Leaving a battery in an extremely high temperature surrounding environment that
can result in an explosion or the leakage of flammable liquid or gas.
A battery subjected to extremely low air pressure that may result in an explosion or
the leakage of flammable liquid or gas.
BATTERIE ATTENTION NOTES
Jetez les piles usagées conformément aux instructions.
Remplacement d'une batterie avec un type incorrect qui peut annuler une sauvegarde
(par exemple, dans le cas de certains types de batterie au lithium)
Mise au rebut d'une batterie dans le feu ou dans un four chaud, ou écrasement ou
coupure mécanique d'une batterie pouvant entraîner une explosion.
Laisser une batterie dans un environnement environnant à des températures
extrêmement élevées pouvant entraîner une explosion ou la fuite de liquide ou de
gaz inflammable.
Une batterie soumise à une pression atmosphérique extrêmement basse pouvant
provoquer une explosion ou une fuite de liquide ou de gaz inflammable.
警告
本電池如果更換不正確會有爆炸的危險，請依製造商說明書處理用過之電池。
Views of the PS-3416/3416E
Front View
P-CAP Touch Panel
Gen 7E Base
LED Indicator
3
Rear View
Left Side View Right Side View
Bottom View
MSR Port Cover
Bottom I/O Cover
Power Button
Brightness
Adjustment Button “+”
Brightness
Adjustment Button “-”
HDD Cover
Rear I/O Cover
Hinge for LCD
Neck Cover
Cable Cover
Cable Exit
2nd Display
Screw Hole
4
View of I/O Interface
Top I/O Ports Rear I/O Ports
1
COM4 Port
3
Parallel (LPT) Port
Connector
2
USB 2.0 Port
4
PS/2_KB Pin Header
※
The top I/O ports are provided for COM-based and USB-based peripheral
devices, for example, customer display.
Bottom I/O Ports
1
RJ45 LAN Port
2
USB 2.0 Port
3
VGA Port
4
COM Port
(COM3/COM2/COM1)
5
RJ11 Cash Drawer Port
6
12VDC-IN Power Jack
Terminal from shipping mode to operation mode
In consideration of proper packaging, before shipping, the terminal is folded,
staying in shipping mode. Thus, when receiving the product, you will find that
the terminal is well folded, as shown below.
1
2
3
4
1
2
3
4
5
6
5
Before operating this terminal, unfold it and make this terminal rise in
operation mode by referring to the following steps. Here, an equivalent model
with GEN 7 base is taken below for example.
1. Firstly, lift this terminal gently to make it
to be unfolded.
2. Overturn this terminal in the direction as
indicated by the arrow in the right figure.
3. Place this terminal on a flat table.
4. Tilt this terminal to a degree in the direction as indicated by the arrow
below.
6
5. Remove the cable cover from the base.
6. Fix the base with two #/6/32-14L screws.
7. Push the cable cover back to the base.
Terminal from operation mode to shipping mode
To fold this terminal, refer to the following steps. Here, an equivalent model
with GEN 7 base is taken below for example.
1. Remove the cable cover.
2. Remove the two screws from the base.
7
3. Carefully hold the lower rim of the display.
4. Push the base-folding lever in the direction as indicated by the arrow
below (1). Then, the display will be loosen and go down (2).
5. When the display goes down to a degree, loose the base-folding lever, as
shown in the direction as indicated by the arrow below.
6. Then, gently tilt the display in the direction as indicated by the arrow
below until the display is well folded.
1
2
8
7. Put back the cable cover.
Installing Optional Upgrade Kits and Peripherals
PS-3416/3416E can work with multiple optional upgrade kits and peripheral
devices, such as magnetic stripe reader (MSR), LCD monitor, cash drawer and
the like.
Before installing an optional upgrade kit and/or peripheral device, make sure
that the system is powered off and the external power source is removed from
the POS box to prevent electric hazard! Failure to follow the warning
description will void the product warranty!
For the detailed instruction, refer to each of the user manuals of the optional
upgrade kits and peripheral devices.
Connecting Power Adapter and I/O Cables
Before connecting power adapter and I/O cables to the I/O ports of PS series
terminal, please route and arranging the cables. Refer to the following step-by-
step instruction of cable routing and arrangement for the details. Here, an
equivalent model with GEN 7 base is taken below for example.
1. Press the circled section of the cable
cover with your thumb.
9
2. Pull out the cable cover.
3. Push and tilt the terminal to the end in
the direction as shown by the arrow.
Then determine that the terminal is tilted
to the end, as shown in the right figure.
4. Press the circled section with two
thumbs and pull by force the two sides
of the locking hook with two forefingers
as indicated by the arrow.
5. Remove the neck cover from the base
stand.
Pull out
10
6. Tilt the terminal slightly at a little angle in the direction as shown by the
arrow, making cables easily pass through the cable passage.
7. Make the connector, which will be connected to the I/O port of the
terminal, pass through the cable passage of base stand.
8. Push and tilt the terminal to the
end in the direction as shown by
the arrow.
Cable Passage
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels POSIFLEX Terminal tactile
POSIFLEX
POSIFLEX PST-7000 Series Manuel utilisateur
POSIFLEX
POSIFLEX XT-7315 Manuel utilisateur
POSIFLEX
POSIFLEX TX-3700 Series Manuel utilisateur
POSIFLEX
POSIFLEX Jiva TP-8000 Manuel utilisateur
POSIFLEX
POSIFLEX Cash Drawer CR400X Manuel utilisateur
POSIFLEX
POSIFLEX RT-1016A-G2 Manuel utilisateur
POSIFLEX
POSIFLEX HS-3510W-E Manuel utilisateur
POSIFLEX
POSIFLEX XT-3817 Manuel utilisateur
POSIFLEX
POSIFLEX Jiva TP-5815 Pro series Manuel utilisateur
POSIFLEX
POSIFLEX XT-3615 Manuel utilisateur
POSIFLEX
POSIFLEX XT-3015 Manuel utilisateur
POSIFLEX
POSIFLEX MT-5208A Manuel utilisateur
POSIFLEX
POSIFLEX HT-4600 Series Manuel utilisateur
POSIFLEX
POSIFLEX KS-6115 Manuel utilisateur
POSIFLEX
POSIFLEX JIVA HS-3310A Manuel utilisateur
POSIFLEX
POSIFLEX HC-1521 Series Manuel utilisateur
POSIFLEX
POSIFLEX HT-4600 Series Manuel utilisateur
POSIFLEX
POSIFLEX KS-6115 Manuel utilisateur
POSIFLEX
POSIFLEX HT-4000 Series Manuel utilisateur
POSIFLEX
POSIFLEX Jiva LT - 8300 Manuel utilisateur
Manuels Terminal tactile populaires d'autres marques
Wincor Nixdorf
Wincor Nixdorf iPOS plus Advanced Manuel utilisateur
Ingenico
Ingenico AXIUM EX4000 Manuel utilisateur
Heisei Electronics
Heisei Electronics Q-POS 815 Manuel utilisateur
Amano
Amano MTX-15 Manuel utilisateur
FLOWBIRD
FLOWBIRD CWT Compact Touch Manuel utilisateur
Demco
Demco SP7 Manuel utilisateur
