POSIFLEX HS-3310A-G2 Manuel utilisateur

Package Contents

HS-3310A-G2/3314A-G2 desktop POS (x 1)

24V/60W Power Adaptor (x 1)

Power cord (x 1)

3-inch wide thermal paper roll (x 1)

Paper separator for 2” thermal paper roll (x 1)

Desktop mounting kit pack for HS-3310A-G2 (x 1)

(including 1 desktop mounting bracket,

4 fixing screws, and 4 plastic anchors)

Desktop mounting kit pack for HS-3314A-G2 (x 1)

(including 1 bottom plate, 1 desktop mounting

bracket, 4 fixing screws, and 4 plastic anchors)

User manual (x 1)

15670903010 Ver. A0

http://www.posiflex.com

HS-3310A-G2/3314A-G2

Desktop POS

User Manual

SOME IMPORTANT NOTES

FCC NOTES

This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own expense.

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may cause

undesired operation.

CE CLASS A WARNING

This equipment is compliant with Class A of CISPR 32. In a residential environment

this equipment may cause radio interference.

AVERTISSEMENT CE CLASSE A

Cet équipement est conforme à la classe A de CISPR 32. Dans un environnement

résidentiel, cet équipement peut provoquer des interférences radio.

WARRANTY LIMITS

Warranty will terminate automatically when the machine is opened by any person other

than the authorized technicians. The user should consult his/her dealer for the problem

happening. Warranty voids if the user does not follow the instructions in application of

this merchandise. The manufacturer is by no means responsible for any damage or

hazard caused by improper application.

LIMITES DE GARANTIE

La garantie prend fin automatiquement lorsque la machine est ouverte par une personne

autre que les techniciens autorisés. L'utilisateur doit consulter son revendeur pour le

problème qui se produit. La garantie s'annule si l'utilisateur ne suit pas les instructions

d'application de cette marchandise. Le fabricant n'est en aucun cas responsable de tout

dommage ou danger causé par une mauvaise application.

警告使用者

此為甲類資訊技術設備，於居住環境中使用時，可能會造成射頻擾動，在此種情

況下，使用者會被要求採取某些適當的對策。

SAFETY INSTRUCTIONS

This equipment is not suitable for use in locations where children are likely to be

present.

CONSIGNES DE SÉCURITÉ

Cet équipement ne convient pas àune utilisation dans des lieux pouvant accueillir des

enfants.

WARNING

Power cord shall be connected to a socket-outlet with earthing connection

BATTERY CAUTION NOTES

Dispose of used batteries according to the instructions.

Replacement of a battery with an incorrect type that can defeat a safeguard (for

example, in the case of some lithium battery types)

Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting

of a battery that can result in an explosion.

Leaving a battery in an extremely high temperature surrounding environment

that can result in an explosion or the leakage of flammable liquid or gas.

A battery subjected to extremely low air pressure that may result in an

explosion or the leakage of flammable liquid or gas.

BATTERIE ATTENTION NOTES

Jetez les piles usagées conformément aux instructions.

Remplacement d'une batterie avec un type incorrect qui peut annuler une

sauvegarde (par exemple, dans le cas de certains types de batterie au lithium)

Mise au rebut d'une batterie dans le feu ou dans un four chaud, ou écrasement

ou coupure mécanique d'une batterie pouvant entraîner une explosion.

Laisser une batterie dans un environnement environnant àdes températures

extrêmement élevées pouvant entraîner une explosion ou la fuite de liquide ou

de gaz inflammable.

Une batterie soumise à une pression atmosphérique extrêmement basse pouvant

provoquer une explosion ou une fuite de liquide ou de gaz inflammable.

警告

本電池如果更換不正確會有爆炸的危險，請依製造商說明書處理用過之電池。

Cable Exit

Views of HS-3310A-G2/3314A-G2

Front View

Rear View

Power LED Indicator

Printer Error

LED Indicator

Printer Paper-Out

LED Indicator

3-Track Magnetic

Stripe Reader

(Optional)

Printed Paper Exit

HS-331xA-G2

P-CAP Touch & LCD Panel

Fingerprint or iButton

Sensors (Optional)

Posiflex 2D Scanner

(Optional)

Paper Jam Rescue

Compartment

Top I/O Interface

Cable Cover

Bottom I/O Interface

Cable Cover

Feed Button

Left Side View Right Side View

Bottom View

Views of I/O Interface of HS-331xA-G2

Top I/O Interface

Bottom I/O Interface

Rubber Pad

HDMI Port

Rubber Pad

Mounting holes

Micro SD Card Slot

USB 3.0 Port

Reset Button

Line Out Port

12V DC-OUT

Power Jack

Paper Roll Cover

Release Lever

RFID Card Reader

(Optional)

Power Button

Bottom I/O Interface

Connecting Power Adapter

Please refer to the following instructions on how to connect power adapter to

HS-331xA-G2 and to organize your cables.

1. Lay your desktop POS on a level surface

with its touch screen facing down as shown

in the figure.

2. Hold the bottom I/O interface cover with

your thumb and forefinger, and then gently

pull the cover outwards to remove the

cover.

3. Connect power adapter and I/O cables to

the bottom I/O interface.

4. Have the cover join to the wedge portions

of the bottom I/O interface.

24V DC-IN Power Jack

USB 2.0 Port

DB-9 COM Ports

RJ-45 LAN Port

Cash Drawer Port

5. Before pushing the cover back into place,

neatly thread the cables through the cable

exit.

6. Press down the cover to close the bottom

I/O interface chamber.

CAUTION:

On doing insertion or extraction of a cable connector,

please always hold the connector head itself instead of

pulling the cable wire. Doing this could damage the

cables and ports, which is considered as an artificial

damage and is not covered by the warranty.

ATTENTION:

Lors de l'insertion ou de l'extraction d'un connecteur de

câble, veuillez toujours tenir la tête du connecteur elle-

même au lieu de tirer le fil du câble. Cela pourrait

endommager les câbles, ce qui est considéré comme un

dommage artificiel et n'est pas couvert par la garantie.

Le cordon d'alimentation doit être connecté à une prise

de courant avec mise à la terre.

Loading 2” or 3” Paper Rolls

Before operating the printer, please follow the below steps to load a paper roll.

1. To open the paper roll cover, push down the

paper roll cover release lever in the direction

shown in the figure.

2. Before installing 2-inch paper roll in the thermal printer, place paper

separator in the paper roll compartment by following the instructions

below. If you are using 3” paper roll for the printer, please skip to

next step.

2.1. Hold the separator with the sharp-

pointed side down.

Cable Exit

2.2. Push the sharp-pointed part of paper

separator into the slot on the bottom

of the paper roll compartment.

2.3. Slide another side of paper separator into the slot on the top

of the paper roll compartment.

2.4. Drop 2-inch paper roll inside the

paper roll compartment.

3. To load the thermal printer with the 3-inch

paper roll, just drop the thermal paper roll

inside the paper roll compartment of the

printer as illustrated in the figure.

4. Unroll the thermal paper and drag the loose

end of the paper till it extends towards the

paper cutter.

Paper cutter

5. Make sure the loose end sticks out of the

opening of the paper roll compartment. Then,

close the paper roll cover by pushing it back

at the center of the top side of the cover with

a click sound.

6. Make sure the paper roll is well loaded with

the end of the paper sticking out as shown in

the figure.

To avoid paper jam or other printing errors, do NOT

press the paper roll cover release lever during printing.

Troubleshooting Paper Jams

When it comes to the common printing problems, it is inevitable that you

might encounter the issue of paper jams at some point. The following steps are

provided to assist you in fixing the problem. Before proceeding, make sure that

your POS terminal is properly shut down.

1. Open the paper jams rescue compartment by

sliding the cover in the direction shown by

the arrow.

2. In the paper jams rescue compartment, find

the adjustment wheel, which mainly allows

you to manually adjust the cutting position of

the cutter blade.

3. Keep rotating the wheel until the cutter blade

is completely retracted.

Adjustment wheel

4. Observe the cutter position through the paper exit slot to ensure the

cutter blade moves upward to the retracted position.

5. Gently push down paper roll cover release

lever to open the paper roll cover. If the

cover is still stuck, please repeat Step 3 and

Step 4.

6. Remove the jammed paper, reinstall the paper roll, and then close the

paper roll cover firmly.

Mounting the POS onto a Table

This section will describe two alternative solutions to help you fix the POS

firmly onto a table in preventing your POS system from being rocked, tipped

or tilted accidentally.

Using bottom plate

Please follow the steps below to install the bottom plate for HS-3314A-G2.

1. Take the bottom plate with the mounting bracket out of the package,

and place it with its screw holes on the top in your preferred position.

2. Support your POS terminal with its

screen facing towards you. Then, align

the two screw bolts on the bottom of the

POS with the rail slots of the mounting

bracket.

Bottom Plate

Mounting bracket

Screw holes

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels POSIFLEX Terminal tactile

POSIFLEX

POSIFLEX LCD Customer Display PD-7100 Manuel utilisateur

POSIFLEX

POSIFLEX Jiva 5815 Pro Manuel utilisateur

POSIFLEX

POSIFLEX HT-4312 Series Manuel utilisateur

POSIFLEX

POSIFLEX HT-3600 Series Manuel utilisateur

POSIFLEX

POSIFLEX XT-3015 Manuel utilisateur

POSIFLEX

POSIFLEX Jiva KS-6615 Series Manuel utilisateur

POSIFLEX

POSIFLEX TM-7117E Manuel utilisateur

POSIFLEX

POSIFLEX PS-3415 Manuel utilisateur

POSIFLEX

POSIFLEX SA-304 Manuel utilisateur

POSIFLEX

POSIFLEX MT-4308W Series Manuel utilisateur

POSIFLEX

POSIFLEX XT-2614E Manuel utilisateur

POSIFLEX

POSIFLEX JIVA TP-5700 Manuel utilisateur

POSIFLEX

POSIFLEX XT-2614Q Manuel utilisateur

POSIFLEX

POSIFLEX DT-207 series Manuel utilisateur

POSIFLEX

POSIFLEX Jiva KS-6615 Series Manuel utilisateur

POSIFLEX

POSIFLEX PST-7000 Series Manuel utilisateur

POSIFLEX

POSIFLEX PS Series Manuel utilisateur

POSIFLEX

POSIFLEX PS-3515 Manuel utilisateur

POSIFLEX

POSIFLEX DT-308 Series Manuel utilisateur

POSIFLEX

POSIFLEX HT-3200 SERIES Manuel utilisateur

POSIFLEX

POSIFLEX TX-3700 Series Manuel utilisateur

POSIFLEX

POSIFLEX KS-6115 Manuel utilisateur

POSIFLEX

POSIFLEX XT-5315 Manuel utilisateur

POSIFLEX

POSIFLEX HT-4000 Series Manuel utilisateur

Manuels Terminal tactile populaires d'autres marques

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Manuel utilisateur

Ingenico

Ingenico AXIUM EX4000 Manuel utilisateur

Heisei Electronics

Heisei Electronics Q-POS 815 Manuel utilisateur

Amano

Amano MTX-15 Manuel utilisateur

FLOWBIRD

FLOWBIRD CWT Compact Touch Manuel utilisateur

Demco

Demco SP7 Manuel utilisateur

Lathem

Lathem PC600 Series Manuel utilisateur

Partner

Partner MF-2352 Manuel utilisateur

NCR

NCR RealPOS 7460-2 Manuel

Simrad

Simrad MS50 Instructions de montage

Unitech

Unitech MR350 MKII Guide de démarrage rapide

Jungheinrich

Jungheinrich WMT 210 Manuel utilisateur

Motorola

Motorola MTP850 Manuel utilisateur

YASKAWA

YASKAWA 62H-MDC0 Manuel utilisateur

MVG industries

MVG industries NeptuLink Manuel utilisateur

Price Industries Limited

Price Industries Limited FDC Manuel d'instructions

Honeywell

Honeywell TemaKey Manuel utilisateur

EBN

EBN BPC65-B-A16G Manuel utilisateur