Planet IGSW-24040T Manuel utilisateur

Industrial 24-Port 10/100/1000Mbps

with 4 Shared SFP Managed Gigabit Switch

IGSW-24040T

Quick Installation Guide

Table of Contents

1. Package Content.......................................................................................... 3

2. Requirements .............................................................................................. 3

3. Wiring DC Power Inputs ............................................................................... 4

4. Terminal Setup ............................................................................................ 5

5. Logon to the Console ................................................................................... 6

6. Congure IP Address ................................................................................... 7

7. Start Web Management................................................................................ 9

8. Customer Support .....................................................................................12

1. Package Content

Thank you for purchasing PLANET Industrial Layer 2 Managed Switch, IGSW-

24040T. Terms of “Managed Switch” means the Switch mentioned titled in the

cover page of this Quick installation guide, i.e. IGSW-24040T.

Open the box of the Managed Switch and carefully unpack it. The box should

contain the following items:

 The IGSW-24040T Switch x 1

User’s Manual CD x 1

 Quick Installation Guide x 1

RS232 Cable x 1

Rubber Feets x 4

 Two Rack-mounting Brackets with Attachment Screw x 1 (set)

 Power Cord x 1

If any item is found missing or damaged, please contact your local reseller for

replacement.

2. Requirements

 Workstations of subscribers running Windows XP/2003/Vista/7/2008, MAC OS9

or later, Linux, UNIX or other platform compatible with TCP/IP protocols.

 Workstation installed with Ethernet NIC (Network Interface Card)

Serial Port connect (Terminal)

 Above PC with COM Port (DB9)

Ethernet Port connect

 Network cables - Use standard network (UTP) cables with RJ-45 connectors.

 Above PC installed with WEB Browser and JAVA runtime environment Plug-in.

Note

It is recommended to use Internet Explore 7.0 or above to access

the Managed Switch.

3. Wiring DC Power Inputs

The 6-contact terminal block connector on the rear panel of IGSW-24040T is used

for two DC redundant powers input. Please follow the steps below to insert the

power wire.

1. Insert positive / negative DC power wires into the contacts 1 and 2 for DC

POWER 1, or 5 and 6 for DC POWER 2.

OFF

Fault

N/AGNDDO 1DO 0DI 1DI 0

DC 2DC 1

AC POWER 100~240V AC

50/60Hz

Please refer to user’s manual before

connect the DC wire.

DC Input Range: 36V~72V DC

CAUTION

2. Tighten the wire-clamp screws for preventing the wires from loosing.

123456

DC 1 Fault Alarm DC 2

+-+-

Note

The wire gauge for the terminal block should be in the range

between 12 ~ 24 AWG.

4. Terminal Setup

To congure the system, connect a serial cable to a COM port on a PC or

notebook computer and to serial (console) port of the Managed Switch. The console

port of the Managed Switch is DCE already, so that you can connect the console

port directly through PC without the need of Null Modem.

PC / Workstation

with

Terminal emulation software

RS-232

Serial Port Serial Port

115200,8,n,1

PLANET Managed Switch

A terminal program is required to make the software connection to the Managed

Switch. Windows’ Hyper Terminal program may be a good choice. The Hyper

Terminal can be accessed from the Start menu.

1. Click START, then Programs, Accessories and then Hyper Terminal.

2. When the following screen appears, make sure that the COM port should be

congured as:

♦ Baud: 115200

♦Data bits : 8

♦ Parity : None

♦Stop bits : 1

♦ Flow Control : None

5. Logon to the Console

Once the terminal has connected to the device, power on the Managed Switch, the

terminal will display that it is running testing procedures.

Then, the following message asks the login username and password. The factory

default username and password as following and the login screen in Figure 5-1

appears.

Username: admin

Password: admin

Figure 5-1: IGSW-24040T Managed Switch Console Login Screen

Note

1. For security reason, please change and memorize the new pass-

word after this first setup.

2. Only accept command in lowercase letter under console inter-

face.

6. Congure IP Address

The Managed Switch is shipped with default IP address as following.

IP Address: 192.168.0.100

Subnet Mask: 255.255.255.0

To check the current IP address or modify a new IP address for the Switch, please

use the procedures as follow:

Show the current IP address

1. On “Switch/>” prompt, enter “show ip”.

2. The screen displays the current IP address, Subnet Mask and Gateway. As show

in Figure 6-1.

Figure 6-1: Show IP Information Screen

 Congure IP address

3. On “Switch/> ” prompt, enter the following command and press <Enter>. As

show in Figure 6-2.

Switch/> ip setup 192.168.1.100 255.255.255.0 192.168.1.1

The previous command would apply the follow settings for the Switch.

IP Address: 192.168.1.100

Subnet Mask: 255.255.255.0

Gateway: 192.168.1.1

Figure 6-2: Set IP Address Screen

4. Repeat Step 1 to check if the IP address is changed.

If the IP is successfully congured, the Managed Switch will apply the new IP

address setting immediately. You can access the Web interface of the Managed

Switch through the new IP address.

Note

If you do not familiar with console command or the related param-

eter, enter “help” anytime in console to get the help description.

7. Start Web Management

The following shows how to start up the Web Management of the Managed

Switch. Note the Managed Switch is congured through an Ethernet connection,

please make sure the manager PC must be set on the same IP subnet address.

For example, the default IP address of the Managed Switch is 192.168.0.100,

then the manager PC should be set at 192.168.0.x (where x is a number between

1 and 254, except 100), and the default subnet mask is 255.255.255.0.

PLANET Managed Switch

RJ-45/UTP-Cable

PC / Workstation

with

IE Browser

IP Address:

192.168.0.x

IP Address:

192.168.0.100

Figure 7-1: IP Management Diagram

Login the Managed Switch

1. Use Internet Explorer 7.0 or above Web browser, enter IP address

http://192.168.0.100 (the factory-default IP address or that you have just

changed in console) to access the Web interface.

2. When the following dialog box appears, please enter the default username and

password “admin” (or the password you have changed via console). The login

screen in Figure 7-2 appears.

Default Username: admin

Default Password: admin

Figure 7-2: Login Screen

3. After entering the password, the main screen appears as Figure 7-3.

Figure 7-3: Web Main Screen of the Managed Switch

4. The Switch Menu on the left of the Web page let you access all the commands

and statistics the Switch provides.

Figure 7-4: Switch Menu

Note

If you do not familiar with Switch functions or the related param-

eter, press “Help” button anytime at left of the Web page to get

the help description.

Autres manuels pour IGSW-24040T

Table des matières

Autres manuels Planet Changer

Planet

Planet WGSW-28040 Manuel utilisateur

Planet

Planet IKVM-1000 Manuel utilisateur

Planet

Planet IGS-4215 Series Manuel utilisateur

Planet

Planet XDL-2420R Manuel utilisateur

Planet

Planet IGS-4215-4P4T Manuel utilisateur

Planet

Planet POE-400 Manuel utilisateur

Planet

Planet MGSW-004 Manuel utilisateur

Planet

Planet WGSD-1022 Manuel utilisateur

Planet

Planet XGS-6350-48X2Q4C Manuel utilisateur

Planet

Planet SGSW-24040R Manuel utilisateur

Planet

Planet FSD-804P Manuel utilisateur

Planet

Planet GSW-2401 Manuel utilisateur

Planet

Planet GSD-805 Manuel utilisateur

Planet

Planet GS-4210-8P2T2S Manuel utilisateur

Planet

Planet FGSW-2022VHP Manuel utilisateur

Planet

Planet HPOE-460 Manuel utilisateur

Planet

Planet MGS-6320-8HP2X Manuel utilisateur

Planet

Planet ISW-1022MT Manuel utilisateur

Planet

Planet GSD-808HP Manuel utilisateur

Planet

Planet FSD-808P Manuel utilisateur

Planet

Planet FGSW-4840S Manuel utilisateur

Planet

Planet EPL-2000 Manuel utilisateur

Planet

Planet FGSW-1820CS Manuel utilisateur

Planet

Planet ISW-1022M Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur