Planet FNSW-1600P Manuel utilisateur
16-Port 10/100BASE-TX 802.3at PoE Switch
FNSW-1600P
User’s Manual
Table of Contents
1. Package Contents........................................................................................ 3
2. Product Features ......................................................................................... 4
3. Product Specications .................................................................................. 5
4. Hardware Description .................................................................................. 6
4.1 Front Panel........................................................................................... 6
4.2 Rear Panel............................................................................................ 6
5. Hardware Installation................................................................................... 8
5.1 Desktop Installation .............................................................................. 8
5.2 Rack Mounting...................................................................................... 9
6. Troubleshooting..........................................................................................11
7. Customer Support ......................................................................................13
3
1. Package Contents
Thank you for purchasing PLANET 16-Port 10/100TX 802.3at PoE Switch, FNSW-
1600P. Open the box of the PoE Switch and carefully unpack it. The box should
contain the following items:
PoE Switch x 1 User’s Manual x 1
Power Cord x 1 Accessories x 1
If any of these are missing or damaged, please contact your dealer immediately;
if possible, retain the carton including the original packing material, and use them
again to repack the product in case there is a need to return it to us for repair.
4
2. Product Features
Physical Port
16 10/100BASE-TX RJ45 ports with IEEE 802.3at PoE+ injector
Power over Ethernet
Complies with IEEE 802.3at Power over Ethernet Plus/mid-span PSE
Supports PoE power up to 30 watts for each PoE port
125W PoE power budget
Auto detects powered device (PD)
Circuit protection prevents power interference between ports
Remote power feeding up to 100m
Switching
Hardware-based 10/100Mbps auto-negotiation and auto MDI/MDI-X
Flow control for full duplex operation and back pressure for half duplex opera-
tion
Integrates address look-up engine, supporting 8K absolute MAC addresses
Automatic address learning and address aging
Case and Installation
19-inch desktop size, 1U height
LED indicators for PoE ready, PoE activity
2 silent fans to provide stable and efcient power performance
Rack-mountable, Plug-and-Play installation
Note
PSE (Power Sourcing Equipment) is a device (switch or hub
for instance) that will provide power in a PoE setup. The maximum
allowed continuous output power per such device in IEEE 802.3af is
15.4 watts and in IEEE 802.3at is 30 watts.
PD (Powered Device) such as IP phone, network camera or wire-
less access point is a PoE-enabled terminal that consumes energy
supplied by PSE.
5
3. Product Specications
Model FNSW-1600P
Hardware Specications
Copper Ports 16 10/100BASE-TX RJ45 auto-MDI/MDI-X ports
PoE Inject Port 16 ports with 802.3at/af PoE injector function with
Port-1 to Port-16
LED Indicators
System: Power(Green)
Port 1 to Port 16: 10/100 LNK/ACT (Green)
PoE-in-Use (Orange)
Switch Architecture Store-and-Forward
Address Table 8K entries, automatic source address learning and
aging
Switch Fabric 3.2Gbps/non-blocking
Throughput
(packet per second) 2.38Mpps@64 bytes
Power Requirements AC 100~240V, 50/60Hz, 2A max.
Power Consumption Max. 133.3 watts/457.4 BTU
Dimensions (W x D x H) 445 x 207 x 45 mm
Weight 2330g
Power over Ethernet
PoE Standard IEEE 802.3af Power over Ethernet/PSE
IEEE 802.3at Power over Ethernet Plus/PSE
PoE Power Supply Type Mid-span
PoE Power Output Per port 52V DC max. 30.8 watts
Power Pin Assignment 4/5(+), 7/8(-)
PoE Power Budget 125 watts
Standards Conformance
Regulatory Compliance FCC Part 15 Class A, CE
Standards Compliance
IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX/100BASE-FX
IEEE 802.3x ow control and back pressure
IEEE 802.3af Power over Ethernet
IEEE 802.3at Power over Ethernet Plus
Environment
Operating Temperature: 0 ~ 50 degrees C
Relative Humidity: 5 ~ 95% (non-condensing)
Storage Temperature: -10 ~ 70 degrees C
Relative Humidity: 5 ~ 95% (non-condensing)
6
4. Hardware Description
4.1 Front Panel
The front panel of the 16-Port 10/100TX 802.3at PoE switch consists of 16 auto-
sensing 10/100Mbps Fast Ethernet RJ45 ports. The LED indicators are also located
on the front panel of the FNSW-1600P.
2 4 6 8 10 12 14 16
1 3 5 7 9 11 13 15
2
1
PWR
4
3
6
5
8
7
10
9
12
11
14
13
16
15
FNSW-1600P
ACT10/100 LNK
PoE In-use
PoE
16-Port 10/100TX
802.3at PoE+ Ethernet Switch
Figure 4-1: FNSW-1600P Switch Front Panel
4.2 Rear Panel
The rear panel of the FNSW-1600P comes with an AC inlet power socket, which
accepts input power from 100 to 240V AC, 50-60Hz.
100~240V AC
50 / 60Hz
Figure 4-2: FNSW-1600P Switch Rear Panel
Power
Notice
1. The device is a power-required device, meaning it will not work
till it is powered. If your networks should be active all the time,
please consider using UPS (Uninterrupted Power Supply) for your
device. It will prevent you from network data loss or network
downtime.
2. In some areas, installing a surge suppression device may also
help to protect your FNSW-1600P from being damaged by
unregulated surge or current to the FNSW-1600P or the power
adapter.
7
LED Denition
System
LED Color Function
PWR Green Lights to indicate the Switch has power.
Per 10/100Mbps Port
LED Color Function
PoE-in-Use Orange Lights to indicate the port is providing 52V DC in-line
power.
LNK/ACT Green
Lights to indicate the link through that port is
successfully established.
Blinks to indicate that the Switch is actively sending
or receiving data over that port.
8
5. Hardware Installation
This section describes the functionalities of the PoE switch’scomponents and
guides you to installing it on the desktop and rack mount. Basic knowledge of
networking is assumed. Please read this chapter completely before continuing.
5.1 Desktop Installation
To install the Switch on the desktop, simply follow the steps below:
Step1: Attach the rubber feet to the recessed areas on the bottom of the Switch,
as shown in Figure 5-1.
2 4 6 8 10 12 14 16
1 3 5 7 9 11 13 15
2
1
PWR
4
3
6
5
8
7
10
9
12
11
14
13
16
15
FNSW-1600P
ACT10/100LNK
PoEIn-use
PoE
16-Port 10/100TX
802.3at PoE+ Ethernet Switch
Figure 5-1: Attaching the Rubber Feet to the Switch
Step 2: Place the Switch on the desktop near an AC power source.
Step 3: Keep enough ventilation space between the Switch and the surrounding
objects.
Step 4: Connect your Switch to 802.3af/at complied powered devices and other
network devices.
A. Connect one end of a standard network cable to the 10/100TX RJ45
ports on the front panel of the Switch.
B. Connect the other end of the cable to the network devices such as
printer servers, workstations and router.
Step 5: Supply power to the Switch.
A. Connect one end of the power cable to the Switch.
B. Connect the power plug of the power cable to a standard wall outlet.
When the Switch receives power, the power LED should remain solid green.
9
5.2 Rack Mounting
To install the Switch in a 19-inch standard rack, follow the instructions described
below.
Step 1: Place your Switch on a hard at surface, with the front panel positioned
towards your front side.
Step 2: Attach a rack-mount bracket to each side of the Switch with supplied
screws attached to the package. Figure 5-2 shows how to attach brackets
to one side of the Switch.
2 4 6 8 10 12 14 16
1 3 5 7 9 11 13 15
2
1
PWR
4
3
6
5
8
7
10
9
12
11
14
13
16
15
FNSW-1600P
ACT10/100LNK
PoEIn-use
PoE
16-Port 10/100TX
802.3at PoE+ Ethernet Switch
Figure 5-2: Attaching the Brackets to the Switch.
You must use the screws supplied with the mounting brackets.
Damage caused to the parts by using incorrect screws would invali-
date the warranty.
Step 3: Secure the brackets tightly.
Step 4: Follow the same steps to attach the second bracket to the opposite side.
10
Step 5: After the brackets are attached to the Switch, use suitable screws to
securely attach the brackets to the rack, as shown in Figure 5-3.
2 4 6 8 10 12 14 16
1 3 5 7 9 11 13 15
2
1
PWR
4
3
6
5
8
7
10
9
12
11
14
13
16
15
FNSW-1600P
ACT10/100LNK
PoEIn-use
PoE
16-Port 10/100TX
802.3at PoE+ Ethernet Switch
Figure 5-3: Mounting the Switch in a Rack
Step 6: Proceed with Steps 4 and 5 of Section 5.1 Desktop Installation to
connect the network cabling and supply power to your Switch.
Autres manuels pour FNSW-1600P
1
Table des matières
Autres manuels Planet Routeur réseau
Planet
Planet IGS-10020 Manuel utilisateur
Planet
Planet IGS-6325 DIN rail Series Manuel utilisateur
Planet
Planet GSD-800S Manuel utilisateur
Planet
Planet WGS3-2840 Manuel utilisateur
Planet
Planet ADE-3410 Manuel utilisateur
Planet
Planet ERT-805 Manuel utilisateur
Planet
Planet G.SHDSL.bis Bridge Router GRT-504 Manuel utilisateur
Planet
Planet FSD-805 Manuel utilisateur
Planet
Planet ADW-4401 A/B Manuel utilisateur
Planet
Planet FNSW-1601 Manuel utilisateur
Planet
Planet SW-501 Manuel utilisateur
Planet
Planet G.SHDSL.bis Bridge Router GRT-504 Manuel utilisateur
Planet
Planet GS-4210-24P2S Manuel utilisateur
Planet
Planet GSW-2400HPS Manuel utilisateur
Planet
Planet WNRT-625G Manuel utilisateur
Planet
Planet WNRT-320GS Manuel utilisateur
Planet
Planet ISW-800M Manuel utilisateur
Planet
Planet WGD-800 Manuel utilisateur
Planet
Planet IAD-200 Manuel utilisateur
Planet
Planet WGSW-2620HP Manuel utilisateur
Manuels Routeur réseau populaires d'autres marques
NETGEAR
NETGEAR FS526T - Switch Manuel utilisateur
Korenix
Korenix JetNet 5710G Series Manuel utilisateur
Automated Logic
Automated Logic ZN551 Manuel du propriétaire
Cisco
Cisco ASR 1000 Series Manuel de l'opérateur
EnGenius
EnGenius ESR-9710 Manuel utilisateur
Cisco
Cisco 805 Series Instructions d'utilisation et de sécurité