Phottix Ares Manuel utilisateur
INSTRUCTION MANUAL
MANUEL D’UTILISATION
BENUTZERHANDBUCH
MANUAL DE INSTRUCCIONES
INSTRUKCJA OBSŁUGI
РУКОВОДСТВО ПОЛЬЗОВАТЕЛЯ
说明书
說明書
2
40
13
22
31
49
59
68
En
Fr
De
Es
Pl
Ru
CnSimp
Cn Trad
Phottix Ares Flash Trigger
Instructions
Parts
Transmitter
1. Status LED
2. Channel Numbers
3. Channel Adjustment Buttons
4. Fire All Button
5. Test Button
6. Swivel Rotator
7. Locking Ring
8. Camera Hot Shoe Connection
9. Power Switch
10. Battery Cover
11. Battery Compartment
2
1
2
3
4
5
7
8
9
6
10
11
3
Receiver
1. Status LED
2. Hot Shoe Connection
3. Power Switch
4. DC Power Port
5. Channel Numbers
6. Channel Adjustment Buttons
7. 3.5mm Output Port
8. Battery Cover
9. Battery Compartment
10. Locking Ring
11. Cold Shot / Tripod Lug
En INSTRUCTION MANUAL
1
5
6
9
8
2
10
11
3
4
7
4
1. Phottix Ares receivers are designed to work in
camera and ash manual mode and have no
TTL functions.
2. Phottix Ares receivers will re hot shoe ashes
that are triggered from the center contact pin.
Some third party ashes that trigger from
auxiliary hot shoe pins will not trigger when
used on the Ares receiver hot shoe. Flashes will
trigger via sync cable if the ash has a sync port.
Tip: Turn o all devices – ashes/strobes,
cameras, and Phottix Ares transmitters and
receivers - when connecting and disconnecting
devices.
Please Note
1. Press the battery cover in while pushing it
away from the Ares transmitter or receiver. The
battery cover will snap open.
2. Remove the battery cover from the Ares.
3. Insert AA batteries as shown inside the
battery compartment.
4. Replace the battery cover and push back into
the locked position.
Inserting Batteries
1. The Transmitter Test Button will test re
remote ashes/strobes.
2. To Test: Press the Transmitter Test Button –
ashes/strobes connected to Phottix Ares
receivers on the same channel will re.
Test Button
5
En INSTRUCTION MANUAL
1. The Status LED on the front of the Phottix
Ares transmitter will ash green approximately
every one second when in standby mode. It will
turn red when a signal is being transmitted.
2. The Status LED on the Phottix Ares receiver
will ash green approximately every one
second while in standby mode. The LED will
turn red when a signal is received from the
transmitter.
3. When battery power is low the Status LED on
the transmitter or receiver will quickly ash red
indicating low power and the need to change
batteries.
Status LED
1. The Phottix Ares has eight channel settings.
2. Press the Channel Adjustment Buttons (left
or right) on the transmitter or receiver to set
the channel.
3. Channel Numbers 1 to 8 will illuminate on
the transmitter or receiver to indicate which
channel the device is set to.
4. Phottix Ares transmitters will only trigger
receivers set to the same channel.
Setting Channels
1. To turn on the Phottix Ares transmitter or
Turning Transmitter and Receiver
On/O
receiver - move the power switch to the “ON”
position.
2. To turn o the Phottix Ares transmitter or
receiver - move the power switch to the “OFF”
position.
6
1. To re all ashes or strobes on receivers set to
dierent channels press the Fire All Button on
the transmitter.
2. The Channel Numbers 1 to 8 will illuminate.
3. All nearby Ares receivers set to any channel in
standby mode will re connected ashes/
strobes.
4. To turn o Fire All mode press the Fire All
Button. The channel selection will revert to its
previous setting.
Fire All Channels Switch
1. Turn o the camera and Phottix Ares transmit-
ter.
2. Slide the Ares transmitter into the camera’s
The Phottix Ares transmitter can be used in an
up or down position.
1. To lower the transmitter: After mounting,
gently push the Ares transmitter forward to use
in the down position. The transmitter will lock
in place in the down position.
2. To raise the transmitter: gently pull the Ares
transmitter up. The transmitter will lock in
place in the up position.
Connecting the transmitter to the
camera hot shoe
Raising and Lowering the
Transmitter
hot shoe mount.
3. Turn the Ares locking ring until tight.
4. Turn on the camera, Ares transmitter and set
the shooting mode to Manual.
7
En INSTRUCTION MANUAL
1. Turn o the ash/strobe and the Phottix Ares
receiver.
2. Connect a cable to the receiver’s 3.5 mm Sync
Port.
3. Connect the opposite end of the cable to a
ash or studio strobe (A 6.3 mm adapter is
included for studio strobes with larger ports).
4. Turn on the ash/strobe and the Phottix Ares
receiver. Set the ash/strobe to Manual mode.
* It is not unusual for the ash to discharge once
after turning on the Phottix Ares.
Connecting a ash/strobe to the
Ares receiver by sync cable
1. Turn o the ash and the Phottix Ares
receiver.
2. Slide the ash into the receiver’s hot shoe
mount.
3. Lock the ash with the ash’s locking mecha-
nism.
4. Turn on the ash and the Phottix Ares
receiver.
5. Set the ash to Manual mode.
* It is not unusual for the ash to discharge once
after turning on the Phottix Ares.
Connecting a ash to the Ares
Receiver hot shoe
8
Technical Specs
Transmitter
Frequency: 2.4 GHz
Range: 200m +
Channel: 8 channels and Fire All Function
Power: 2 x AA batteries (Transmitter and Receiver), 5V DC (Receiver)
Max sync speed: 1/250 sec*
Antenna: internal antenna
Working Temperature: 0℃～+40℃
Working Humidity: 35﹪～95﹪RH
* On compatible cameras/ashes
Input Voltage: 2.2-3.2V
Current: Maximum Working Current ≤45mA, Standby Current: 7mA (single channel), 27mA (all channels),
O Current Info: 0mA
Dimensions: 104mmx50mmx35mm
Weight: With batteries: 108g, Without batteries: 61g
Receiver
Input Voltage: 2.2-3.2V (DC Input Voltage :5V)
9
En INSTRUCTION MANUAL
Current: Maximum Working Current ≤26mA, Standby Current≤15mA, O Current Info: 0mA
Ports: 3.5mm sync port, hot shoe output
Dimensions: 88mmx50mmx40mm
Weight: With batteries: 108g, Without batteries: 61g
10
- This product is a precise electronic instrument.
Do not expose to damp environments or dust.
- Do not drop or crush.
- Do not disassemble.
- Do not use harsh chemical(s) or solvents to
clean the body. Use a soft cloth or lens paper.
- Interference: The Phottix Ares transmits and
receives radio signals at 2.4 GHz. Its
performance can be aected by electrical
current, magnetic elds, radio signals, wireless
routers, cellular phones, and other electronic
devices. Environmental objects, such as large
buildings or walls, trees, fences, or cars can also
aect performance. If your Ares receiver will not
trigger move its location slightly.
Warnings
Table des matières
Langues :
Autres manuels Phottix Accessoires pour appareils photo
Phottix
Phottix Atlas Manuel utilisateur
Phottix
Phottix odin II TTL Manuel utilisateur
Phottix
Phottix Ares II Manuel utilisateur
Phottix
Phottix Laso Manuel utilisateur
Phottix
Phottix Juno Manuel utilisateur
Phottix
Phottix Atlas Manuel utilisateur
Phottix
Phottix Strato TTL Manuel utilisateur
Phottix
Phottix PPL-200 Manuel utilisateur
Phottix
Phottix Nuada S VLED Manuel utilisateur
Phottix
Phottix Nuada R3 Manuel utilisateur
Phottix
Phottix TR-90 Manuel utilisateur
Phottix
Phottix Indra360 TTL Manuel utilisateur
Phottix
Phottix Odin Manuel utilisateur
Phottix
Phottix Nuada Ring 10 Manuel utilisateur
Phottix
Phottix Nuada S Manuel utilisateur
Phottix
Phottix Odin TTL Manuel utilisateur
Phottix
Phottix Strato II Multi Manuel utilisateur
Phottix
Phottix odin II TTL Manuel utilisateur
Phottix
Phottix Laso Manuel utilisateur
Phottix
Phottix Trafo Manuel utilisateur
