Phonak CROS II Manuel utilisateur

Phonak CROS II

March 2015

Desktop Fitting Guide

This guide provides you with a detailed introduction to fitting a Phonak CROS II system in Phonak Target 4.1 and later. or fitting of the

hearing instruments, please see the Hearing Instruments Desktop itting Guide.

Preparation of the hearing instruments

For the fitting of CROS II it is recommended to use iCube II as it enables faster fine tuning and instant demonstration of CROS II.

iCube II

No cables to the hearing instrument or CROS II are needed. Insert

the battery before placing the device on the ear. Turn on the

devices by closing the battery compartment.

NO Hlink or HI-PRO

Connect the programing cables to the hearing instruments and the

fitting device. CROS II is not active with the fittng cables

connected.

Connect the instruments

Click [Connect] to start the fitting. The connected devices will appear next to the

fitting device in the dashboard.

The audiogram data from NOAH will be automatically imported into Phonak Target

and taken into account for the pre-calculation.

Confirm that the correct fitting device is shown. To change the

fitting device, use the pull down arrow next to the fitting device

in the dashboard.

Basic tuning

After the connection, fit the hearing instrument as in a monaural fitting. After the

successful fitting, go to the [Basic tuning] screen to adjust the loudness ratio

between CROS II and the hearing instrument.

For a BiCROS fitting, run the feedback test.

The hearing instrument on the better ear can be adjusted in the same way as in a

standard fitting.

Phonak Target™ 2

Device options

Click [Device options] to adjust the individual settings for the CROS volume / volume and program change (depending on the user

controls available).

or CROS II, the volume of the CROS signal can be adjusted separately, if desired.

Finishing the fitting session

You can close the session at any time by clicking [Save & close session] in the top right corner of the screen. The save dialog will confirm

the successful save of the CROS II fitting. After the save, Phonak Target will guide you to the start screen.

The wireless connection between the CROS II transmitter and hearing aid starts automatically once both instruments have been

disconnected from the fitting device and turned on.

Important: When streaming from the accessories, the CROS II streaming will be automatically disconnected. Reconnection will

also be automatic when you stop streaming of the accessory.

CROS II fitting in Junior Mode

Important: CROS II is not recommended for 0-3 years.

In Junior Mode 4-8 years, the default program setup is Roger/DAI + M (Startup program) and Speech in Noise (2

program) with the push

button disabled.

To access CROS II, go to

[

Fine tuning] 

[

Program manager] and set the

position of Calm Situation to the second position and remove the Speech in Noise

program from the program sequence.

Go to [Device options]  [Push button], enable the [SHOR PRESS] to Program

change.

Once saved and disconnected, toggle to the Calm Situation program to connect

CROS II. The Connect beeps will be heard.

In Junior Modes 9-12 and 13-18, the Startup program is Roger/DAI + M and the push button is enabled by default. AutoSense OS is

available via the push button as an additional program. To access CROS II, toggle to AutoSense OS.

Manufacturer:

Phonak AG

Laubisrütistrasse 28

CH-8712 Stäfa

Switzerland

CE mark applied 2015

Autres manuels Phonak Prothèse auditive

Phonak

Phonak audeo B90-direct Manuel utilisateur

Phonak

Phonak ComPilot Manuel utilisateur

Phonak

Phonak SaviaArt Manuel utilisateur

Phonak

Phonak Versata SR Manuel utilisateur

Phonak

Phonak Exelia Art micro Manuel utilisateur

Phonak

Phonak Q90 Manuel utilisateur

Phonak

Phonak ComPilot Manuel utilisateur

Phonak

Phonak Naida CI Connect Manuel utilisateur

Phonak

Phonak Audeo Yes Manuel utilisateur

Phonak

Phonak Audeo L-R Series Manuel utilisateur

Phonak

Phonak ComPilot Manuel utilisateur

Phonak

Phonak EasyCall Manuel utilisateur

Phonak

Phonak naida ultra power Manuel utilisateur

Phonak

Phonak iCube Manuel utilisateur

Phonak

Phonak Cleck'nTalk Manuel utilisateur

Phonak

Phonak Roger Pen Manuel utilisateur

Phonak

Phonak Phonak Audeo B90-10 Manuel utilisateur

Phonak

Phonak Lyric 3 Manuel utilisateur

Phonak

Phonak Audeo Manuel utilisateur

Phonak

Phonak TVLink II Manuel utilisateur

Phonak

Phonak ComPilot Manuel utilisateur

Phonak

Phonak Una Manuel utilisateur

Phonak

Phonak Nathos S+ ITC W Manuel utilisateur

Phonak

Phonak Naida V90-RIC Manuel utilisateur

Manuels Prothèse auditive populaires d'autres marques

Sonic

Sonic Bliss miniBTE Manuel utilisateur

Lexie

Lexie B1 Manuel de la liste des pièces

Widex

Widex FM+DEX Manuel utilisateur

Siemens

Siemens Triano Manuel utilisateur

Camplicomms

Camplicomms HC-200 Manuel utilisateur

Widex

Widex SUPER 220 S2-VSD Manuel utilisateur

Williams Sound

Williams Sound SoundPlus WIR 237 Mode d’emploi

Oticon Medical

Oticon Medical Ponto SoundConnector Manuel utilisateur

Siemens

Siemens Life micon Manuel utilisateur

Starkey

Starkey Destiny Manuel utilisateur

Audicus

Audicus The Icon Manuel utilisateur

Advanced Bionics

Advanced Bionics Slim HP Standard Manuel utilisateur

Widex

Widex DREAM440 THE DREAM SERIES Manuel utilisateur

NIKEN

NIKEN NK-401 Manuel utilisateur

ON Semiconductor

ON Semiconductor Ezairo 7111 Pre Suite Manuel utilisateur

Sonetik

Sonetik GOHEAR Manuel utilisateur

Widex

Widex FL-9 Manuel utilisateur

Siemens

Siemens MUSIC Pro Pro IT Manuel utilisateur