Philips HQC483 Manuel utilisateur

ENGLISH 4

POLSKI 15

РУССКИЙ 27

EESTI 39

LATVISKI 49

LIETUVIŠKAI 60

БЪЛГАРСКИ 70

SRPSKI 82

HQC483, HQC482, HQC440

Introduction

◗Dear customer, you have made the right

choice! Your new Philips hair clipper adapts to

the contours of the head and enables

comfortable use.

◗To enjoy using the hair clipper for a long time,

we advise you to read the following

information.

Important

Read these instructions for use carefully before

using the appliance and save them for future

reference.

◗Check if the voltage indicated on the adapter

corresponds to the mains voltage in your

home before you connect the appliance.

◗This appliance is suitable for mains voltages

from 220 to 240 volts.

◗Only use the adapter supplied.

◗The adapter contains a transformer. Do not

cut off the adapter to replace it with another

plug, as this will cause a hazardous situation.

◗Do not use a damaged adapter.

◗If the adapter is damaged, always have it

replaced by one of the original type in order

to avoid a hazard.

C◗Keep the appliance and the adapter dry.

◗Keep the appliance out of the reach of

children.

ENGLISH4

C◗Use, charge and store the appliance at a

temperature between 15cand 35c.

◗This appliance is only intended for clipping

human hair. Do not use it for any other

purpose.

◗Noise level: Lc= 69 dB [A].

Charging (HQC482 and HQC483 only)

Charge the appliance for at least 12 hours before

you start using it for the first time.

A fully charged appliance has a cordless operating

time of up to 35 minutes.

Do not charge the appliance for more than 24

hours.

1Make sure the appliance is switched off

while charging.

C2Insert the appliance plug into the

appliance.

3Insert the adapter plug into the wall

socket.

C◗The pilot light will go on to indicate that the

appliance is charging.

ENGLISH 5

Optimising the lifetime of the battery

- Discharge the battery completely twice a year

by letting the motor run until it stops.

- Remove the adapter plug from the wall socket

when the battery is fully charged.

- If the appliance has not been used for a long

time, it must be recharged for at least 12 hours.

Corded clipping

HQC482, HQC483:

Do not run the appliance from the mains when

the battery is fully charged.

◗To use the hair clipper connected to the

mains:

Switch the hair clipper off, connect it to the mains

and wait a few seconds before switching it on.

If the battery is completely empty, wait a few

minutes before switching the appliance on.

HQC440:

◗Insert the apliance plug into the apliance and

put the adapter in the wall socket.

ENGLISH6

Preparing for use

Clipping with comb attachment

C1Before you start clipping, make sure the

head of the person whose hair you are

cutting is at the same level as your chest.

2To get the best results, use the hair clipper

only on dry hair. Do not use it on freshly

washed hair.

3First comb the hair into the direction of

hair growth.

C4Always move the clipper against the

direction of hair growth, otherwise it will

not cut the hair properly.

5Move the clipper through the hair slowly.

Using the appliance

Clipping with comb attachment

C1Slide the comb attachment onto the rails

on the appliance until you hear a click.

2Make sure that the arms of the comb

attachment have been properly slid onto

the rails on both sides.

ENGLISH 7

C3Choose the appropriate hair length

setting.

Press the adjustment button on the back of the

appliance and slide the comb attachment to the

desired position.

The clipper has 7 different hair length settings:

-3mm

-6mm

-9mm

- 12 mm

- 15 mm

- 18 mm

- 21 mm

Start at the setting for maximum hair length

(21 mm) to familiarise yourself with the clipper.

4Make sure that the flat part of the comb

attachment is always fully in contact with

the scalp to obtain an even cutting result.

5Pass the clipper slowly over the crown

from different directions to achieve an

even cutting result.

6Make overlapping passes over the head to

ensure that the clipper catches all the hairs

that need to be cut.

7Comb the hair in the direction of hair

growth from time to time so that the

clipper can catch the hair more easily.

ENGLISH8

8To achieve a good result with curly, sparse

or long hair, you can use a comb to guide

the hair towards the clipper.

9We advise you to regularly remove clipped

hair from the comb while clipping.

Graduation

The Philishave hair clipper not only allows you to

cut the hair evenly at the same length all over the

head, it also enables you to achieve a smooth

transition from longer hair on top of the head to

shorter hair on the back and sides of the head.

1Start clipping at the setting for maximum

hair length (i.e. position 21 mm).

2Then choose a shorter setting and cut the

hair on all parts of the head except the

top, where you want the hair to be longer.

3You can repeat this procedure until the

hair on every part of the head has the

desired length.

Precise contouring without comb

attachment

You can use the clipper without comb attachment

to contour the neckline and the area around the

ears.

Be careful when you are clipping without comb

attachment, for the clipper will remove every hair

it touches.

ENGLISH 9

1Remove the comb attachment by pulling it

off the clipper.

2Before contouring the hairline round the

ears, comb the hair ends over the ear.

3Bend the person's ear to get it out of the

way.

C4Tilt the clipper in such a way that only one

edge of the cutting element touches the

hair ends.

C5Only cut the hair ends.The hairline should

be close to the ear.

C6To contour the nape hairline and the

sideburns, turn the clipper and make

downward strokes.

7Move slowly and smoothly.

C8Just follow the natural hairline.

Cutting over styling comb or fingers

This technique can be used to obtain hair lengths

over 21 mm. Bear in mind that this technique is

difficult to master and should only be applied by

experienced users.

ENGLISH10

1Remove the comb attachment.

C2Comb a small section of hair upwards. Lift

the hair with a styling comb or hold it

between your fingers until only the length

that needs to be cut sticks out.

C3Cut the hair protruding from the comb or

fingers.

4Continue this procedure and comb

frequently to remove cut hair and to check

for unevenly cut sections.

Cleaning

Clean the appliance every time you have used it.

Do not use abrasives, scourers or liquids such as

alcohol, petrol or acetone to clean the appliance.

1Make sure the appliance is switched off

and disconnected from the mains before

you start cleaning it.

C2Remove the comb attachment.

C3Push the middle part of the cutting unit

upwards with your thumb until it opens

and then pull it off the appliance.

Be careful that the cutting unit does not fall to the

floor.

ENGLISH 11

C4Clean the cutting unit and the inside of the

appliance with the brush supplied.

C5Place the lug of the cutting unit into the

slot and push the unit back onto the

appliance.

6Make sure you push the cutting unit back

until you hear a click.

Replacement

A worn or damaged cutting unit should only be

replaced with an original Philips cutting unit.

C1Push the middle part of the cutting unit

upwards with your thumb until it opens

and then pull it off the appliance.

C2Place the lug of the cutting unit into the

slot and push the cutting unit back until

you hear a click.

Environment (HQC482 and HQC483 only)

The built-in rechargeable battery contains

substances which may pollute the environment.

ENGLISH12

Autres manuels pour HQC483

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Philips tondeuse à cheveux

Philips

Philips QC5090 Manuel utilisateur

Philips

Philips QC5550/40 Manuel utilisateur

Philips

Philips HC3412/15 Manuel utilisateur

Philips

Philips HQC440 Manuel utilisateur

Philips

Philips HC3420 Manuel utilisateur

Philips

Philips HQ-C888 Manuel utilisateur

Philips

Philips QC5055/40 Manuel utilisateur

Philips

Philips HC7650 Manuel utilisateur

Philips

Philips QC5170 Manuel utilisateur

Philips

Philips Norelco QC5130/80 Manuel utilisateur

Philips

Philips Beolink 1000 Manuel utilisateur

Philips

Philips QC5090 Manuel utilisateur

Philips

Philips QG3380 Manuel utilisateur

Philips

Philips QC5340/40 Manuel utilisateur

Philips

Philips QT4090 Manuel utilisateur

Philips

Philips HC3505/15 Manuel utilisateur

Philips

Philips QC5015 Manuel utilisateur

Philips

Philips HC5410/83 Manuel utilisateur

Philips

Philips QC5380 Manuel utilisateur

Philips

Philips HQC482 Manuel utilisateur

Philips

Philips Norelco QT4050 Manuel utilisateur

Philips

Philips QC5550/15 Manuel utilisateur

Philips

Philips HC3402/15 Manuel utilisateur

Philips

Philips HQC484/40 Manuel utilisateur

Manuels tondeuse à cheveux populaires d'autres marques

Clatronic

Clatronic HSM 800 Manuel utilisateur

Mellerware

Mellerware MACRO ALDANY MA20001 Manuel utilisateur

Create

Create CLIPPER EASY Manuel utilisateur

VALERA

VALERA X-Master 652 Manuel utilisateur

Wahl

Wahl 1870Li Manuel utilisateur

Remington

Remington HC5780 Manuel utilisateur

Lister

Lister Legend Manuel utilisateur

Andis

Andis MBA 23125 Manuel utilisateur

Shear Magic

Shear Magic Nifty 1800 Manuel utilisateur

Andis

Andis US-1 Guide de référence rapide

Panasonic

Panasonic EH-KA81 Manuel utilisateur

Andis

Andis US-1 Instructions d'installation

Remington

Remington Classic HC450 Manuel utilisateur

Andis

Andis ML Instructions d'installation

O'Barber

O'Barber MINI SLIDE Manuel utilisateur

Oster

Oster 76110 Manuel utilisateur

Hyundai

Hyundai HC 420 Manuel utilisateur

Panasonic

Panasonic ER-GP80 Manuel utilisateur