Philips HQC482 Manuel utilisateur
ENGLISH 4
FRANCAIS 15
34
44
HQC483, HQC482, HQC440
3
á«Hô©dG
Introduction
◗Dear customer, you have made the right
choice! Your new Philips hair clipper adapts to
the contours of the head and enables
comfortable use.
◗To enjoy using the hair clipper for a long time,
we advise you to read the following
information.
Important
Read these instructions for use carefully before
using the appliance and save them for future
reference.
◗Check if the voltage indicated on the adapter
corresponds to the mains voltage in your
home before you connect the appliance.
◗This appliance is suitable for mains voltages
from 220 to 240 volts.
◗Only use the adapter supplied.
◗The adapter contains a transformer. Do not
cut off the adapter to replace it with another
plug, as this will cause a hazardous situation.
◗Do not use a damaged adapter.
◗If the adapter is damaged, always have it
replaced by one of the original type in order
to avoid a hazard.
C◗Keep the appliance and the adapter dry.
◗Keep the appliance out of the reach of
children.
ENGLISH4
C◗Use, charge and store the appliance at a
temperature between 15cand 35c.
◗This appliance is only intended for clipping
human hair. Do not use it for any other
purpose.
Charging (HQC482 and HQC483 only)
Charge the appliance for at least 12 hours before
you start using it for the first time.
A fully charged appliance has a cordless operating
time of up to 35 minutes.
Do not charge the appliance for more than
24 hours.
1Make sure the appliance is switched off
while charging.
C2Insert the appliance plug into the
appliance.
3Insert the adapter plug into the wall
socket.
C◗The pilot light will go on to indicate that the
appliance is charging.
Optimising the lifetime of the battery
- Discharge the battery completely twice a year
by letting the motor run until it stops.
ENGLISH 5
- Remove the adapter plug from the wall socket
when the battery is fully charged.
- If the appliance has not been used for a long
time, it must be recharged for at least 12 hours.
Corded clipping
HQC482, HQC483:
Do not run the appliance from the mains when
the battery is fully charged.
◗To use the hair clipper connected to the
mains:
Switch the hair clipper off, connect it to the mains
and wait a few seconds before switching it on.
If the battery is completely empty, wait a few
minutes before switching the appliance on.
HQC440:
◗Insert the apliance plug into the apliance and
put the adapter in the wall socket.
Preparing for use
Clipping with comb attachment
C1Before you start clipping, make sure the
head of the person whose hair you are
cutting is at the same level as your chest.
2To get the best results, use the hair clipper
only on dry hair. Do not use it on freshly
washed hair.
ENGLISH6
3First comb the hair into the direction of
hair growth.
C4Always move the clipper against the
direction of hair growth, otherwise it will
not cut the hair properly.
5Move the clipper through the hair slowly.
Using the appliance
Clipping with comb attachment
C1Slide the comb attachment onto the rails
on the appliance until you hear a click.
2Make sure that the arms of the comb
attachment have been properly slid onto
the rails on both sides.
C3Choose the appropriate hair length
setting.
Press the adjustment button on the back of the
appliance and slide the comb attachment to the
desired position.
The clipper has 7 different hair length settings:
-3mm
-6mm
-9mm
- 12 mm
- 15 mm
- 18 mm
- 21 mm
ENGLISH 7
Start at the setting for maximum hair length
(21 mm) to familiarise yourself with the clipper.
4Make sure that the flat part of the comb
attachment is always fully in contact with
the scalp to obtain an even cutting result.
5Pass the clipper slowly over the crown
from different directions to achieve an
even cutting result.
6Make overlapping passes over the head to
ensure that the clipper catches all the hairs
that need to be cut.
7Comb the hair in the direction of hair
growth from time to time so that the
clipper can catch the hair more easily.
8To achieve a good result with curly, sparse
or long hair, you can use a comb to guide
the hair towards the clipper.
9We advise you to regularly remove clipped
hair from the comb while clipping.
Graduation
The Philishave hair clipper not only allows you to
cut the hair evenly at the same length all over the
head, it also enables you to achieve a smooth
transition from longer hair on top of the head to
shorter hair on the back and sides of the head.
ENGLISH8
1Start clipping at the setting for maximum
hair length (i.e. position 21 mm).
2Then choose a shorter setting and cut the
hair on all parts of the head except the
top, where you want the hair to be longer.
3You can repeat this procedure until the
hair on every part of the head has the
desired length.
Precise contouring without comb
attachment
You can use the clipper without comb attachment
to contour the neckline and the area around the
ears.
Be careful when you are clipping without comb
attachment, for the clipper will remove every hair
it touches.
1Remove the comb attachment by pulling it
off the clipper.
2Before contouring the hairline round the
ears, comb the hair ends over the ear.
3Bend the person's ear to get it out of the
way.
C4Tilt the clipper in such a way that only one
edge of the cutting element touches the
hair ends.
ENGLISH 9
C5Only cut the hair ends.The hairline should
be close to the ear.
C6To contour the nape hairline and the
sideburns, turn the clipper and make
downward strokes.
7Move slowly and smoothly.
C8Just follow the natural hairline.
Cutting over styling comb or fingers
This technique can be used to obtain hair lengths
over 21 mm. Bear in mind that this technique is
difficult to master and should only be applied by
experienced users.
1Remove the comb attachment.
C2Comb a small section of hair upwards. Lift
the hair with a styling comb or hold it
between your fingers until only the length
that needs to be cut sticks out.
C3Cut the hair protruding from the comb or
fingers.
ENGLISH10
4Continue this procedure and comb
frequently to remove cut hair and to check
for unevenly cut sections.
Cleaning
Clean the appliance every time you have used it.
Do not use abrasives, scourers or liquids such as
alcohol, petrol or acetone to clean the appliance.
1Make sure the appliance is switched off
and disconnected from the mains before
you start cleaning it.
C2Remove the comb attachment.
C3Push the middle part of the cutting unit
upwards with your thumb until it opens
and then pull it off the appliance.
Be careful that the cutting unit does not fall to the
floor.
C4Clean the cutting unit and the inside of the
appliance with the brush supplied.
C5Place the lug of the cutting unit into the
slot and push the unit back onto the
appliance.
ENGLISH 11
6Make sure you push the cutting unit back
until you hear a click.
Replacement
A worn or damaged cutting unit should only be
replaced with an original Philips cutting unit.
C1Push the middle part of the cutting unit
upwards with your thumb until it opens
and then pull it off the appliance.
C2Place the lug of the cutting unit into the
slot and push the cutting unit back until
you hear a click.
Environment (HQC482 and HQC483 only)
The built-in rechargeable battery contains
substances which may pollute the environment.
Remove the rechargeable battery when you
discard the appliance.
Do not throw the battery away with the normal
household waste but hand it in at an official
collection point.
You can also take the appliance to a Philips
service centre, which will remove the battery for
you and will dispose of it in an environmentally
safe way.
ENGLISH12
Autres manuels pour HQC482
1
Ce manuel convient aux modèles suivants
2
Table des matières
Langues :
Autres manuels Philips tondeuse à cheveux
Philips
Philips HQC241 Manuel utilisateur
Philips
Philips Philishave HQC240/20 Manuel utilisateur
Philips
Philips HC3100 Manuel utilisateur
Philips
Philips QC5170/02 Manuel utilisateur
Philips
Philips BG2026 Manuel du propriétaire
Philips
Philips QC5390 Manuel utilisateur
Philips
Philips QC5125 Manuel utilisateur
Philips
Philips QC5050 Manuel utilisateur
Philips
Philips HQC688/60 Manuel utilisateur
Philips
Philips QC5132 Manuel utilisateur
Philips
Philips Hair Clipper QC5000 Manuel utilisateur
Philips
Philips CC 5065 Manuel utilisateur
Philips
Philips BRT381 Manuel utilisateur
Philips
Philips T800 Manuel utilisateur
Philips
Philips QC5045/00 Manuel utilisateur
Philips
Philips HQC442/20 Manuel utilisateur
Philips
Philips QC5115/15 Manuel utilisateur
Philips
Philips QGC5000 Manuel utilisateur
Philips
Philips HC9490 Manuel utilisateur
Philips
Philips QT4040 Philishave Manuel utilisateur
