Pentair AUTOTROL LOGIX 742 Manuel utilisateur

Logix™ No-Salt Detector (Chlorine Generator)

Installation Instructions (North American)

The Logix 742 and 762 controls feature a check salt light

which indicates when the end user should add salt to the

regenerant tank. The Logix control can also be

programmed to produce a low level of chlorine to

chlorinate the resin bed during regeneration. Potassium

chloride or sodium chloride may be used. Installing this

feature is simple.

Step 1

Remove the Logix control from the valve and disconnect

power.

Step 2

Insert the small connector of the no-salt detector cord to

the back of the Logix control. See Figure 1.

Step 3

Remove the existing refill controller and ball from the valve

and replace it with the no-salt detector refill flow control.

See the illustrations to the right for the location of the refill

controller.

Step 4

Insert the large white connector of the no-salt detector

cord to the end of the refill flow control. Press it in firmly to

make sure there is good contact.

Step 5

Reconnect power to the Logix control and reinstall the

control to the valve.

Step 6 742/762 Programming

To activate the chlorine generator/salt detector on the

742/762, follow these instructions:

1. Power up the 742/762 control.

2. Press the UP and DOWN buttons

simultaneously for 5 seconds to enter Level

II programming.

3. Scroll to parameter P13 using the DOWN button.

The controller will display the previous setting.

4. Press the SET button. The display will begin to

flash.

5. Set to one of the following settings as desired:

0 = chlorine generator/salt detector disabled.

1 = salt detector enabled.

2 = chlorine generator with salt detector

enabled.

6. Once the correct setting above is selected, press

SET to enter your setting. After 30 seconds the

controller will return to normal operation mode.

Back of Logix Control

255 Valve Identification

Refill Controller

Injector and Cap

No-Salt Detector

Check Salt Light

Performa Valve Identification

Injector and Cap

Refill Controller

Check Salt Light

Figure 1

Figure 2

Figure 3

Release Tab

(Chlorine Generator) Outlet

Printed in USA P/N 1268103 Rev B

Step 7

Remove the overlay sticker from the Logix control and

replace with the included new overlay that features the

check salt light opening. The old overlay sticker can be

easily peeled off with a knife or screwdriver.

Summary Chlorine Generator

The chlorine generator feature is constantly checking for

salt and will produce chlorine throughout the regeneration

process. This automatic monitoring system will only

produce chlorine when a salt/regenerant is available in the

brine line.

The chlorine generator will produce up to a maximum of

4 ppm of chlorine. The chlorine generator is not designed

to be used with special medias that require chlorine for

proper application. The chlorine generator provides

chlorine for aesthetic chlorination of media bed.

No Salt Detector

The no salt detector operates like the chlorine generator,

except no chlorine is produced.

The check salt light will illuminate whenever the brine

concentration falls below 5 to 7 salometer point.

NOTE: Ensure that the refill rate of the probe

assembly matches the original refill flow

control assembly.

Ce manuel convient aux modèles suivants

Autres manuels Pentair Unité de contrôle

Pentair

Pentair AUTOTROL 740 Manuel utilisateur

Pentair

Pentair AUTOTROL 368 Manuel utilisateur

Pentair

Pentair FLECK 2910 NXT Guide de l'utilisateur

Pentair

Pentair PROSTOP-E Manuel utilisateur

Pentair

Pentair JUNG PUMPEN HIGHLOGO 1-25 LC Manuel utilisateur

Pentair

Pentair Fleck 5800 XTR Guide de l'utilisateur

Pentair

Pentair Fleck 2510 ECONOMINDER Manuel utilisateur

Pentair

Pentair FLECK 2750 Downflow Manuel utilisateur

Pentair

Pentair FLECK 3150 NXT Guide de l'utilisateur

Pentair

Pentair AUTOTROL 742 Series Manuel utilisateur

Pentair

Pentair SUDMO P740 Manuel utilisateur

Pentair

Pentair Fleck 5800 LXT Guide de l'utilisateur

Pentair

Pentair FLECK 3900 NXT Guide de l'utilisateur

Pentair

Pentair FLECK3150 DOWNFLOW Manuel utilisateur

Pentair

Pentair SIATA V132-SFE Manuel utilisateur

Pentair

Pentair AUTOTROL Performa 263 Guide de l'utilisateur

Pentair

Pentair TRACETEK TTDM-128 Manuel de service

Pentair

Pentair E-Box MAESTRO Mode d'emploi

Pentair

Pentair FLECK 7000XTR Manuel utilisateur

Pentair

Pentair FLECK 9000 SXT Guide de l'utilisateur

Pentair

Pentair FLECK 2750 Downflow Manuel utilisateur

Pentair

Pentair F783E Manuel utilisateur

Pentair

Pentair 2510 Manuel utilisateur

Pentair

Pentair AUTOTROL MAGNUM 293 Guide de l'utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur