Peerless-AV CM50 Mode d’emploi

1 of 30 ISSUED: 07-22-08 SHEET #: 120-9054-2 09-30-11

Installation and Assembly:

Flat Panel Corner Mounting Accessory

for 32" – 60" LCD and Plasma Screens

Features

CM50, CM50-S

CM60, CM60-S

2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerlessmounts.com

• Allows screen to fit in corner where space is limited

• CM50(-S) wall units expand to support compatible flat/tilt wall mounts for

screens from 32" – 50"

• CM60(-S) includes additional support plate to accommodate compatible

flat/tilt wall mounts for screens from 40" – 60"

• Wall units accommodate speakers when used with smaller screens (wall

unit maybe visible with some smaller screens)

• Accessory shelf available for A/V components (sold separately)

• Mounts to wood studs, concrete, cinder block

Model Screen Size Range Compatibility

CM50, CM50-S 32"-50"

SF640/ST640

PF640/PT640

SF650/ST650

PF650/PT650

ONE-TP (2-plate configuration)

CM60, CM60-S 40"-60"

SF640/ST640

PF640/PT640

SF650/ST650

PF650/PT650

SF660/ST660

PF660/PT660

ONE-TP (3-plate configuration)

Maximum Load Capacity

175 lb (79.4 kg)

200 lb (90.8 kg)

2 of 30 ISSUED: 07-22-08 SHEET #: 120-9054-2 09-30-11

• Do not begin to install your Peerless product until you have read and understood the instructions and warnings

contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please

call Peerless customer care at 1-800-865-2112.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building

construction, and fully understands these instructions.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardware and components.

• Never exceed the Maximum Load Capacity. See page 1.

• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of

an "edge to edge" stud finder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding

power.

• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal

injury.

• This product was designed and intended to be mounted to the following supporting surfaces checked below with

the hardware included in this product as specified in the installation sheet. To mount this product to an alternative

supporting surface, contact Peerless customer care at 1-800-865-2112.

• This product was designed to be installed on the following wall construction only;

WALL CONSTRUCTION HARDWARE REQUIRED

• Wood Stud Included

•Wood Beam Included

•Solid Concrete Included

•Cinder Block Included

• Brick Contact Qualiﬁed Professional

• Other or unsure? Contact Qualiﬁed Professional

Note: Read entire instruction sheet before you start installation and assembly.

Table of Contents

Parts List.................................................................................................................................................................................3

Installation to Interior Corner Wood Stud Walls......................................................................................................................4

Installation to Exterior Corner Wood Stud Walls.....................................................................................................................5

Installation to Interior Concrete or Cinder Block Walls...........................................................................................................6

Installation to Exterior Concrete or Cinder Block Walls..........................................................................................................7

Attaching Interface Plate and Center Plate ....................................................................................................................... 8, 9

Installing Speaker Mounts................................................................................................................................................... 10

Tools Needed for Assembly

• stud ﬁnder (edge-to-edge stud ﬁnder recommended)

• phillips screwdriver

• drill

• 5/32" drill bit for wood stud wall

• 5/16" drill bit for concrete wall

• level

Accessories

• ACC324(-S) - Shelving Unit for Corner Mount

• ACC930 - Fastener pack for speaker mounts

WARNING

3 of 30 ISSUED: 07-22-08 SHEET #: 120-9054-2 09-30-11

Before you begin, make sure all parts shown are included with your product.

Parts may appear slightly different than illustrated.

ACD

HIJ

Description Qty. CM50 CM50-S CM60 CM60-S

interface plate 2 120-1075 120-4075 120-1075 120-4075

Bwall plate 2 120-1076 120-4076 120-1076 120-4076

Csupport brackets 4 120-1077 120-4077 120-1077 120-4077

Dcenter plate 1 n/a n/a 120-1078 120-4078

E#14 x 2.5" wood screws 8 5S1-015-C03 5S1-015-C03 5S1-015-C03 5S1-015-C03

Fconcrete anchors 8 590-0320 590-0320 590-0320 590-0320

G1/4-20 x 1" round phillips head screw 24 510-9110 510-9110 510-9110 510-9110

H1/4-20 flanged serrated locknut 16 530-1021 530-1021 530-1021 530-1021

I1/4-20 Tinnerman® cage nut 12 530-2050 530-2050 530-2050 530-2050

J1/4" flat washer 24 540-9440 540-9440 540-9440 540-9440

Parts List

4 of 30 ISSUED: 07-22-08 SHEET #: 120-9054-2 09-30-11

Installing to Interior Corner Wood Stud Wall

• Installer must verify that the supporting surface will safely support the combined load of the equipment and all

attached hardware and components.

• Tighten wood screws so that wall plate is ﬁrmly attached, but do not overtighten. Overtightening can damage the

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud ﬁnder

is highly recommended.

• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs.

Installers are responsible to provide hardware for other types of mounting situations.

WARNING

Efig. 1.2

Wall plates (B) can be mounted to one or two studs that are 16" apart. Use a stud finder to locate the edges of

the studs. Use of an edge-to-edge stud finder is highly recommended. Based on their edges, draw a vertical line

down each stud’s center on both walls. NOTE: Depending on placement of studs on wall corners, mounting to

two studs may not be possible.

Determine the distance from the corner of the wall to the inside edge of the wall plates (B) using the equation

below and detail 1 to get distance "X". NOTE: If mounting speaker mounts to sides of corner mount, screen can

be no larger than 40". See page 10 for speaker mount installation.

Measure "X" distance from corner of wall and mark location for inside edge of wall plate. The top mounting slots

of wall plate should be located 3.44" (87 mm) above the desired screen center as shown in fig 1.1. Level wall

plate, align to location marked for inside edge of wall plate and mark four slots in alignment with center of studs.

Repeat for opposite wall plate. Drill 5/32" (4 mm) dia. holes to a minimum depth of 2.5" (64 mm). Make sure that

wall plates are level and secure using #14 x 2.5" wood screws (E).

STUD CS = CENTER OF SCREEN

Bfig. 1.1

"X" = - 21.216

1.414

3.44"

(87 mm)

DETAIL 1

5 of 30 ISSUED: 07-22-08 SHEET #: 120-9054-2 09-30-11

Wall plates (B) can be mounted to one or two studs that are 16" apart. Use a stud ﬁnder to locate the edges of

the studs. Use of an edge-to-edge stud ﬁnder is highly recommended. Based on their edges, draw a vertical line

down each stud’s center on both walls. NOTE: Depending on placement of studs on wall corners, mounting to

two studs may not be possible.

NOTE: If mounting speaker mounts to sides of corner mount, screen can be no larger than 40". See page 10 for

speaker mount installation.

Measure 1" (25 mm) from corner of wall and mark location for inside edge of wall plate. The top mounting slots of

wall plate should be located 3.44" (87 mm) above the desired screen center as shown in ﬁg 1.3. Level wall plate,

align to location marked for inside edge of wall plate and mark four slots in alignment with center of studs. Repeat

for opposite wall plate. Drill 5/32" (4 mm) dia. holes to a minimum depth of 2.5" (64 mm). Make sure that wall

plates are level and secure using #14 x 2.5" wood screws (E).

Installing to Exterior Corner Wood Stud Wall

• Installer must verify that the supporting surface will safely support the combined load of the equipment and all

attached hardware and components.

• Tighten wood screws so that wall plate is ﬁrmly attached, but do not overtighten. Overtightening can damage the

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud ﬁnder

is highly recommended.

• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs.

Installers are responsible to provide hardware for other types of mounting situations.

WARNING

STUD

CS = CENTER OF SCREEN

CORNER

fig. 1.3

fig. 1.4

3.44"

(87 mm)

(25 mm)

6 of 30 ISSUED: 07-22-08 SHEET #: 120-9054-2 09-30-11

Installing to Interior Corner Concrete or Cinder Block Wall

• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete

thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a

solid part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90

speciﬁcations. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a

hammer drill to avoid breaking out the back of the hole when entering a void or cavity.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Installer must verify that the supporting surface will safely support the combined load of the equipment and all

attached hardware and components.

WARNING

Determine the distance from the corner of the wall to

the inside edge of the wall plate (B) using the equation

and detail 1 on page 4 to get distance "X".

NOTE: If mounting speaker mounts to sides of corner

mount, screen can be no larger than 40". See page 10

for speaker mount installation.

Measure "X" distance from corner of wall and

mark location for inside edge of wall plate. The top

mounting slots of wall plate should be located 3.44"

(87 mm) above the desired screen center as shown in

ﬁg 1.1 on page 4. Level wall plate (B), align to location

marked for inside edge of wall plate and mark four

slots in alignment with center of studs. Repeat for

opposite wall plate. Drill 5/16" (8 mm) dia. holes to a

minimum depth of 2.5" (64 mm). Insert anchors (F) in

holes ﬂush with wall as shown (right). Place wall plate

over anchors, make sure that wall plates are level and

secure using #14 x 2.5" wood screws (E).

• Always attach concrete anchors directly to load-

bearing concrete.

• Never attach concrete anchors to concrete covered

with plaster, drywall, or other ﬁnishing material.

If mounting to concrete surfaces covered with

a ﬁnishing surface is unavoidable, the ﬁnishing

surface must be counterbored as shown right.

Be sure concrete anchors do not pull away from

concrete when tightening screws. If plaster/drywall

is thicker than 5/8", custom fasteners must be

supplied by installer.

WARNING

• Tighten screws so that wall plate is ﬁrmly attached,

but do not overtighten. Overtightening can damage

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

WARNING

solid concrete

cinder block

Drill holes and insert anchors (F).

Place plate (B) over anchors (F) and secure with screws (E).

Tighten all fasteners.

concrete

surface

CUTAWAY VIEW

INCORRECT CORRECT

wall

plate wall

plate

plaster/

drywall plaster/

drywall

concrete concrete

7 of 30 ISSUED: 07-22-08 SHEET #: 120-9054-2 09-30-11

Installing to Exterior Corner Concrete or Cinder Block Wall

• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete

thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a

solid part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90

speciﬁcations. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a

hammer drill to avoid breaking out the back of the hole when entering a void or cavity.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Installer must verify that the supporting surface will safely support the combined load of the equipment and all

attached hardware and components.

WARNING

NOTE: If mounting speaker mounts to sides of corner

mount, screen can be no larger than 40". See page 10

for speaker mount installation.

Measure 1" (25 mm) from corner of wall and mark

location for inside edge of wall plate. The top

mounting slots of wall plate should be located 3.44"

(87 mm) above the desired screen center as shown in

ﬁg 1.3 on page 5. Level wall plate (B), align to location

marked for inside edge of wall plate and mark four

slots in alignment with center of studs. Repeat for

opposite wall plate. Drill 5/16" (8 mm) dia. holes to a

minimum depth of 2.5" (64 mm). Insert anchors (F) in

holes ﬂush with wall as shown (right). Place wall plate

over anchors, make sure that wall plates are level and

secure using #14 x 2.5" wood screws (E).

• Always attach concrete anchors directly to load-

bearing concrete.

• Never attach concrete anchors to concrete covered

with plaster, drywall, or other ﬁnishing material.

If mounting to concrete surfaces covered with

a ﬁnishing surface is unavoidable, the ﬁnishing

surface must be counterbored as shown right.

Be sure concrete anchors do not pull away from

concrete when tightening screws. If plaster/drywall

is thicker than 5/8", custom fasteners must be

supplied by installer.

WARNING

• Tighten screws so that wall plate is ﬁrmly attached,

but do not overtighten. Overtightening can damage

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

WARNING

solid concrete

cinder block

Drill holes and insert anchors (F).

Place plate (B) over anchors (F) and secure with screws (E).

Tighten all fasteners.

concrete

surface

CUTAWAY VIEW

INCORRECT CORRECT

wall

plate wall

plate

plaster/

drywall plaster/

drywall

concrete concrete

8 of 30 ISSUED: 07-22-08 SHEET #: 120-9054-2 09-30-11

Attaching Interface Plate

Attach interface plate (A) to wall plate (B) using two sets of 1/4-20 x 1" round phillips head screws (G),

1/4" ﬂat washers (J) and 1/4-20 ﬂanged serrated locknuts (H) as shown in ﬁg 2.1 or 2.2 for interior corners

or ﬁg 2.3 or 2.4 for exterior corners. Repeat for opposite interface plate.

NOTE: Be sure top flange of interface plate (A) rests on top flange of wall plate (B).

NOTE: Do not fully tighten fasteners.

fig. 2.1 fig. 2.2

LEFT INTERIOR CORNER RIGHT INTERIOR CORNER

fig. 2.3 fig. 2.4

LEFT EXTERIOR CORNER RIGHT EXTERIOR CORNER

9 of 30 ISSUED: 07-22-08 SHEET #: 120-9054-2 09-30-11

Installing Support Brackets and Center Plate

NOTE: Use center plate (D) when mounting pattern for wall plate of mount is narrower than opening

between interface plates (A).

Attach support brackets (C) to rear of wall plate (B) using 1/4-20 x 1" round phillips head screw (G),

1/4" ﬂat washer (J) and 1/4-20 ﬂanged serrated locknut (H) for each support bracket as shown below.

NOTE: Be sure ﬂange of support bracket faces inside of interface plate and wall plate. NOTE: Do not

fully tighten fasteners.

Skip to step 3-3 if not installing center plate.

3-1

Swing adapter brackets (C) away from front of

mount. Slide center plate (D) behind interface

plate (A) and center between the two interface

plates. Align top and bottom holes of interface

plate with slots of center plate. Hand thread

1/4-20 x 1" round phillips head screw (G) and

1/4" ﬂat washer (J) through top hole only.

3-2

Swing adapter brackets (C) towards front of

mount. Guide top adapter bracket through top

screw and fasten using 1/4-20 ﬂanged serrated

locknut (H). Align hole of bottom adapter bracket

with bottom hole and fasten using 1/4-20 x 1"

round phillips head screw (G), 1/4" ﬂat washer (J)

and 1/4-20 ﬂanged serrated locknut (H).

3-3

10 of 30 ISSUED: 07-22-08 SHEET #: 120-9054-2 09-30-11

DETAIL 2

Installing Speaker Mounts (optional)

NOTE: Corner mount may be visible with smaller size screens.

NOTE: Speaker mount (sold separately) may appear different than illustrated.ACC930 (sold separately) is required

to attach speaker mount.

Using hole pattern shown below, attach speaker mount to interface plate (A) using two screws and two washers

through the front and two nuts through the rear. NOTE: Fasteners not included for installing speaker mount.

All other brand and product names are trademarks or registered trademarks of their respective owners.

Align wall plate of wall mount with interface plates (A) to determine location of cage nuts (I) used to

secure wall plate to interface plates. Install cage nuts from rear side of interface plates (A) as shown

in detail 2.

NOTE: Install wall plate and remaining wall mount assembly according to instructions provided with

wall mount.

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels peerless-AV Support et étagère

peerless-AV

peerless-AV MSA-101 Mode d’emploi

peerless-AV

peerless-AV DS-LEDTK Series Manuel utilisateur

peerless-AV

peerless-AV SMARTMOUNT ST660 Manuel utilisateur

peerless-AV

peerless-AV ACC918 Manuel utilisateur

peerless-AV

peerless-AV DS-LEDF Series Manuel utilisateur

peerless-AV

peerless-AV MOD-ASC2 Manuel utilisateur

peerless-AV

peerless-AV ESHV30 Manuel utilisateur

peerless-AV

peerless-AV MOD-PRSKIT100-B Manuel utilisateur

peerless-AV

peerless-AV DS-VW765-LQR Manuel utilisateur

peerless-AV

peerless-AV DS-VWC555-3x2 Mode d’emploi

peerless-AV

peerless-AV PJF3-EXA Manuel utilisateur

peerless-AV

peerless-AV EWL-OH55F Manuel utilisateur

peerless-AV

peerless-AV LCW420A Mode d’emploi

peerless-AV

peerless-AV ACSBR1 Manuel utilisateur

peerless-AV

peerless-AV LCT620AD Mode d’emploi

peerless-AV

peerless-AV SmartMount ACC-VCS Manuel utilisateur

peerless-AV

peerless-AV ACC116 Manuel utilisateur

peerless-AV

peerless-AV SUA737 Mode d’emploi

peerless-AV

peerless-AV DSF265P Manuel utilisateur

peerless-AV

peerless-AV MSA-301 Mode d’emploi

peerless-AV

peerless-AV DS-LEDBXT Series Manuel utilisateur

peerless-AV

peerless-AV DST660 Mode d’emploi

peerless-AV

peerless-AV SA746P Manuel utilisateur

peerless-AV

peerless-AV SR575K Manuel utilisateur

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur

peerless-AV CM50 Mode d’emploi

Manuels Support et étagère populaires d'autres marques