peerless-AV FPZ-670 Mode d’emploi
Max Load Capacity 400 lb (181.4 kg)
200 lb (90.7 kg) Max Load Capacity per screen
3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com
ISSUED:05-08-08 SHEET#:202-9280-1
Installation and Assembly:
Flat Panel Stand for 50" - 71" Plasma Screens
Model: FPZ-670
Features:
• Fits single or back-to-back 50" - 71" flat panel screen
• Up to Vesa screens with additional PLP screen
• Supportsnon-Vesascreens withadapter plate(sold separately)
• Internal cable management to easily route cords from the screen to the base of the stand
• Basecover is designed to conceal content drivers and surge protectors
• Vertical adjustment on 6" columns for ideal screen viewingheight
• Hook-on design allows screen to rest in place while screen is being secured
• Portraitor landscape orientation
2 of 7 ISSUED: 05-08-08 SHEET #: 202-9280-1
Note: Read entire instruction sheet before you start installation and assembly.
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please
callPeerless customer care at1-800-729-0307.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Makesure thatthe supporting surface will safely support the combined load of the equipment and all attached hard-
wareandcomponents.
• Neverexceed the Maximum LoadCapacity.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screwsfirmly,but do notovertighten. Overtightening candamage the items,greatly reducing theirholding
power.
WARNING
Table of Contents
Parts List..............................................................................................................................................................................3
Floor Stand Assembly ..........................................................................................................................................................4
Attaching Adapter Plate to Screen with VESA 200 x 200 Mounting Pattern .........................................................................6
Attaching Adapter Plate to PLP Adapter Bracket .................................................................................................................6
Installing Flat Panel Screen on Floor Stand ..........................................................................................................................7
3 of 7 ISSUED: 05-08-08 SHEET #: 202-9280-1
Forcustomer care call (800) 729-0307or (708) 865-8870.
E
D
B
C
R
F
M
I
J
NO
QS
H
A
K
J
G
L
PT
Description Qty. Part #
Amain tube 2 580-1159
Bbase 1 104-1055
Ccarriage 1 104-1063
Dadapter plate 2 104-1065
Ebase cover 1 104-1068
Fcable access cover 1 130-1153
GM5 x 8 mm socket pin screw 2 520-1062
HM4 x 10 mm phillips screw 4 504-9012
IM4 x 20 mm 4 504-9020
JM6 x 12 mm pan head 4 520-1128
KM6 x 20 mm phillips screw 4 520-9402
LM6 x 30 mm phillips screw 4 510-9109
M128 x 313 x 437H retaining spacer 4 590-5005
NM10 x 15 mm socket screw 4 520-9262
OM6 x 20 mm serrated washer head socket pin screw 4 510-9554
Pbumper strip 1 570-1030
Q5/16-24 x 1/4 set screw 8 520-9566
R6 mm allen wrench 1 560-9716
S4 mm allen wrench 1 560-9646
TM5 x 10 mm socket pin serrated washer head 1 510-1126
Parts List
4 of 7 ISSUED: 05-08-08 SHEET #: 202-9280-1
Slide two main tubes (A) onto base (B) and secure
using four set screws (Q) as shown in figure 2 and
detail 1. Tighten screws using 4 mm allen wrench (S).
1 2
fig 2
For some situations, bumper strip (P) may be
requiredto keep base (B) level. If so, cut bumper
strip(P) intofive equalpieces andadhere onepiece
to each corner and one piece to center of bottom
side of base (B).
Note: The pieces can also be used in other locations
on the base's bottom for other situations.
P
B
43
A
B
EE
GT
Slidebase cover(E) downtubes (A)onto base(B) as
shown below. Secure using two M5 x 8 mm socket
pin screws (G). Tighten screws using 4 mm allen
wrench(S).
Note: Make sure that notches on bottom of base
cover fit into holes in base.
Slide cable access cover (F) into base cover (E) as
shown below. Secure using socket pin serrated
washerhead screw (T). Tighten screws using 4mm
allenwrench (S).
A
BDETAIL 1
Q
5 of 7 ISSUED: 05-08-08 SHEET #: 202-9280-1
Slide carriage (C) onto main tubes (A). Slide carriage to desired height and secure using four set screws (Q)
as shown in detail 1. Tighten screws using 4 mm allen wrench (T).
Note: Orientation of "UP" arrow is critical.
5
Q
AC
DETAIL 1
6 of 7 ISSUED: 05-08-08 SHEET #: 202-9280-1
Choose hole pattern as shown in figure 6.1. Attach
adapter plate (D) to back of screen using four M6 x
12 mm screws (J) as shown.
Note: Orientation of "UP" arrow is critical.
*Note: If screw (J) gets less than three threads of
engagement, attach adapterplate(D)to back of
screen using four M6 x 20 mm screws (K). If screw
(K) still gets less than three threads of engagement,
use four M6 x 30 mm screws (L).
Skip to step 7 on page 7.
N
6
For screen compatibility please refer to the plasma interface list on our website www.peerlessmounts.com or call
customer care for a screen specific adapter bracket (PLP models). GENERICADAPTER
BRACKET
AttachingAdapterPlatetoScreenwithVESA200x200MountingPattern
• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly
secured, damage may occur to screen or product may fail.
WARNING
AttachingAdapterPlatetoPLPModelAdapterBracket
6
fig 6.1
D
J
fig 6.2
D
Note: Refer to PLP model adapter bracket instruction
sheet for attachment of adapter bracket to screen.
Choose hole pattern as shown in figure 6.2. Attach
adapter plate (D) to back of screen using four M10 x
15 mm screws (N) as shown. Tighten screws using 6
mmallenwrench(R).
Note: Orientation of "UP" arrow is critical.
7 of 7 ISSUED: 05-08-08 SHEET #: 202-9280-1
To install second screen, repeat steps six and seven for back side of carriage (C).
Hook adapter plate (D) onto carriage (C) and secure using two M6 x 20 mm serrated washer head socket pin screws
(O) as shown in figure 5 and detail 3. Tighten screws using 4 mm allen wrench (S).
7
DETAIL 3 fig 5
8
©2008PeerlessIndustries,Inc.Allrightsreserved.
PeerlessisaregisteredtrademarkofPeerlessIndustries,Inc.
Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.
D
C
D
Portrait orientation
Choose hole pattern as shown in figure 6.3. Attach adapter plate (D) to back of screen using four M10 x 15 mm
screws (N) as shown. Tighten screws using 6 mm allen wrench (R).
Note: Orientation of "UP" arrow is critical.
6
fig 6.3
O
N
Table des matières
Autres manuels peerless-AV Support et étagère
peerless-AV
peerless-AV SR898-EUK Manuel utilisateur
peerless-AV
peerless-AV ACC570 Manuel utilisateur
peerless-AV
peerless-AV LCC 18-C Mode d’emploi
peerless-AV
peerless-AV DS-S560-2X2 Manuel utilisateur
peerless-AV
peerless-AV MOD-FPSKIT100-B Manuel utilisateur
peerless-AV
peerless-AV DS-LEDF Series Manuel utilisateur
peerless-AV
peerless-AV SR598ML3 Manuel utilisateur
peerless-AV
peerless-AV PR565 Manuel utilisateur
peerless-AV
peerless-AV MOD-PRSKIT100-B Manuel utilisateur
peerless-AV
peerless-AV SUA746PU Manuel utilisateur
peerless-AV
peerless-AV SPL746 Manuel utilisateur
peerless-AV
peerless-AV DS-LEDTK Series Manuel utilisateur
peerless-AV
peerless-AV AEC Series Manuel utilisateur
peerless-AV
peerless-AV SR598ML3E Manuel utilisateur
peerless-AV
peerless-AV ACCXT400 Mode d’emploi
peerless-AV
peerless-AV DCT Series Manuel utilisateur
peerless-AV
peerless-AV ESHV30 Manuel utilisateur
peerless-AV
peerless-AV GC-X360S-W Manuel d'instructions
peerless-AV
peerless-AV 0735029276050 Manuel utilisateur
peerless-AV
peerless-AV ACCXT201 Mode d’emploi
Manuels Support et étagère populaires d'autres marques
Salamander
Salamander Acadia AC/W/L400/WH Manuel utilisateur
Fohhn
Fohhn VAT-09 Guide de l'utilisateur
ricoo
ricoo FS0522 Manuel utilisateur
AMSOIL
AMSOIL BMK-22 Guide rapide
Kargo Master
Kargo Master 48220 Manuel utilisateur
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur
