peerless-AV DST660 Mode d’emploi
2300 White Oak Circle • Aurora, IL 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerlessmounts.com
ISSUED: 12-16-11 SHEET #:125-9272-1
Maximum Load Capacity:
125 lb (46 kg)
Model: DST660
Installation and Assembly:
PORTRAIT LANDSCAPE
2 of 9 ISSUED: 12-16-11 SHEET #:125-9272-1
IMPORTANT! Read instruction sheet before you start installation and assembly.
Table of Contents
Parts List.................................................................................................................................................................................3
Installation to Double Wood Stud Wall ...................................................................................................................................4
Installation to Solid Concrete or Cinder Block ........................................................................................................................5
Installation to Metal Stud Wall ................................................................................................................................................6
Attaching Adapter Plate to Screen..........................................................................................................................................8
Attaching Adapter Plate to Wall Plate .....................................................................................................................................9
Tools Needed for Assembly
• stud nder ("edge to edge" stud nder is recommended)
• phillips screwdriver
• drill
• 1/4" (6 mm) bit for concrete and cinder block wall
• 5/32" (4 mm) bit for wood stud wall
•level
• 6 mm allen wrench
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US
customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact
your local distributor.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
• Never exceed the Maximum Load Capacity. See page one.
• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of
an "edge to edge" stud nder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws rmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.
• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal
injury.
• This product was designed to be installed on the following wall construction only;
WALL CONSTRUCTION HARDWARE REQUIRED
•Wood Stud Included
• Wood Beam Included
• Solid Concrete Included
• Cinder Block Included
•Metal Stud Included
•Brick Contact Qualied Professional
•Other or unsure? Contact Qualied Professional
WARNING
3 of 9 ISSUED: 12-16-11 SHEET #:125-9272-1
Before you begin, make sure all parts shown are included with your product.
Parts may appear slightly different than illustrated.
A
B
C D EFG
H I J
K
L M N
O
P
Q
Description Qty. Part #
Awall plate 1 145-1482
Badapter plate 1 145-1461
C#14 x 2.5" wood screw 6 5S1-015-C03
Dconcrete anchor 6 590-0320
EM8 x 12 mm phillips screw 4 520-9571
FM4 x 12 mm phillips screw 4 504-9013
GM5 x 12 mm phillips screw 4 520-1027
HM6 x 12 mm phillips screw 4 520-1128
IM10 x 15 mm socket screw 4 520-9262
J#8 SAE flat washer 4 540-1001
K3/4" x 3/16" x 10" adhesive strip 2 570-1029
Lcable tie 4 560-9711
M4 mm security allen wrench 1 560-9646
N1/4-20 x 2.5" phillips screw 6 520-9521
O1/4" SAE washer 10 540-9440
Ptoggler 6 560-9708
QM5 x 12 mm socket pin serrated washer head screw 6 510-1064
Radapter bracket 2 145-1463
S1/4-20 nylock nu
t
4 530-9413
Parts List
R
S
4 of 9 ISSUED: 12-16-11 SHEET #:125-9272-1
Installation to Double Wood Stud Wall
Wall plate (A) can be mounted to two studs that are 16" apart. Use a stud nder to locate the edges of the studs.
Use of an edge-to-edge stud nder is highly recommended. Based on their edges, draw a vertical line down
each stud’s center. Place wall plate on wall as a template. Level plate, and mark the center of the six mounting
holes. Make sure that the mounting holes are on the stud centerlines. Drill six 5/32" (4 mm) dia. holes 2-1/2"
(64 mm) deep. Make sure that the wall plate is level, secure it using six #14 x 2.5" wood screws (C) as shown.
Skip to step 2
• Installer must verify that the supporting surface will safely support the combined load of the equipment and all
attached hardware and components.
• Tighten wood screws so that wall plate is rmly attached, but do not overtighten. Overtightening can damage the
screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud nder
is highly recommended.
• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Install-
ers are responsible to provide hardware for other types of mounting situations.
WARNING
C
A
STUD
1
5 of 9 ISSUED: 12-16-11 SHEET #:125-9272-1
1
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete
thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid
part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specica-
tions. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to
avoid breaking out the back of the hole when entering a void or cavity.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard-
ware and components.
WARNING
solid concrete
A
C
D
cinder block
• Tighten screws so that wall plate is rmly attached,
but do not overtighten. Overtightening can damage
screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).•
Always attach concrete anchors directly to load-
bearing concrete.
• Never attach concrete anchors to concrete covered
with plaster, drywall, or other nishing material. If
mounting to concrete surfaces covered with a nish-
ing surface is unavoidable, the nishing surface must
be counterbored as shown below. Be sure concrete
anchors do not pull away from concrete when tight-
ening screws. If plaster/drywall is thicker than 5/8",
custom fasteners must be supplied by installer.
WARNING
CUTAWAY VIEW
INCORRECT CORRECT
wall plate
wall plate concrete
plaster/
dry wall
concrete
plaster/
dry wall
Make sure that wall plate (A) is level, use it as a
template to mark six mounting holes. Drill six 5/16"
(8 mm) dia. holes to a minimum depth of 2.5"
(64 mm). Insert anchors (D) in holes ush with wall
as shown.
Place wall plate over anchors and secure with
six #14 x 2.5" screws (C). Level, then tighten all
fasteners.
1
3
2
D
Drill holes and insert anchors (E).
Place plate (A) over anchors (D) and secure with screws (C).
Tighten all fasteners.
A
D
C
concrete
surface
6 of 9 ISSUED: 12-16-11 SHEET #:125-9272-1
Using a stud nder, locate and mark the edges of the metal stud used in mounting this product. Use of an edge
to edge stud nder is highly recommended. Use a level to draw a level, vertical line down the center of the stud.
Level wall plate, and mark the center of the six mounting holes. Make sure that the mounting holes are on the stud
centerlines. Drill six 1/2" holes through drywall and metal studs. NOTE: It may be necessary to drill 5/32" pilot holes
prior to drilling 1/2" holes. Install togglers (P) as shown in gure 1.1. Loosely fasten wall plate to wall using six
1/4-20 x 2-1/2" screws (N) and six 1/4" washers (O) as shown in gure 1.2. Level, hold, and then tighten all screws.
1
• Drywall must be 1/2" or thicker, and metal stud must be 24 gauge or thicker.
• Make sure that the wall will safely support the combined load of the equipment and all attached hardware and
components.
• Make sure that togglers are anchored into the center of the studs. The use of an "edge to edge" stud nder is highly
recommended.
WARNING
Installation to Metal Studs
A
P
N
g.1.2
O
Rotate toggler (P) clockwise to wedge it
against inside walls of metal stud.
Push into hole.
Pivot end of toggler (O).
Slide plastic cap forward while pulling back
rmly on ring.
Break off excess.
P
1
2
3
4
5
g.1.1
drill
1/2"
hole
P
P
P
P
7 of 9 ISSUED: 12-16-11 SHEET #:125-9272-1
Place adhesive strips (K) on the wall plate (A) in location that will allow the most contact with CPU
as shown in gure 2.1.
Note: Placement of adhesive strips will vary depending on size of CPU as shown in gure 2.2
2
NOTE: Safety belt may need to be loosened to attach CPU to wall plate (A).
Press CPU against adhesive strips on wall plate and tightly secure safety belt against CPU.
3
CPU
A
K
A
SAFTEY
STRAP
g.2.1
Placement of Adhesive Strips
Attach CPU to Wall Plate
g.2.2
FRONT VIEW
8 of 9 ISSUED: 12-16-11 SHEET #:125-9272-1
• If screws don't get three complete turns in the screen
inserts or if screws bottom out and bracket is still
not tightly secured, damage may occur to screen or
product may fail.
WARNING
4
Use gure 5.1 to determine placement of adapter brackets (R) on the adapter plate (B) using
1/4-20 nylock nut (S) as shown.
NOTE: For displays with 400mm x 400mm VESA hole patterns adapter brackets (R) are not used.
NOTE: For displays with 800mm, or 600mm VESA hole pattern use ACC-V800X (sold separately).
5
DEDICATED
MOUNTING PATTERNS
15.75"
(400 mm)
7.87"
(200 mm)
11.81"
(300 mm)
7.87"
(200 mm)
3.94"
(100 mm)
1.97"
(50 mm)
BACK VIEW
DISPLAY NOT SHOWN
FOR CLARITY
11.81"
(300 mm)
M4 x 12 mm screws (F)
with #8 washers (J)
M6 x 12 mm screws (H)
with 1/4" washers (O)
M8 x 12 mm screws (E)
E, F, G or H
J or O
AttachingAdapterPlatetoDisplay
Determine hole pattern of display and fasteners used.
Hand thread screws (E, F, G or H) through washers (J or O)
and adapter brackets (R) into screen as shown in gure 4.1.
M5 x 12 mm screws (G)
with 1/4" washers (O)
g.4.1
R
R
B
g.5.1
S
B
M10 x 15 mm socket
screws (I) in (200 mm)
position when mounting
PLP adapter plate
PLP
ADAPTER
PLATE
9 of 9 ISSUED: 12-16-11 SHEET #:125-9272-1
Thread two M5 x 15 mm socket pin screws (Q) into bottom holes of wall plate (A) leaving 1/8" space between
head of screw and wall plate as shown in gure 6.1. Guide hook slots of adapter plate (B) onto screws (Q), while
supporting weight of screen, align top holes of wall plate and adapter bracket to the desired tilt angle and secure
with two M5 x 15 mm socket pin screws (Q) as shown in gure 6.2. Tighten all screws securely.
6
AttachingAdapterPlatetoWallPlate
NO TILT
5° TILT
10° TILT
1/8"
HOOK
SLOTS
BOTH SIDES
NOTE: When display is in portrat position make sure that top screw (Q) is foward as shown in g. 7.1.
Loosen top two M5 x 15 mm socket pin screws (Q) 1/4 turn and temporarily remove bottom two M5 x 15 mm socket
pin screws (Q) on adapter plate (A) as shown in gure 7.2. Swing screen forward and swing support brackets
downward into adapter plate (B) to brace screen in open position as shown in gure 7.3.
7
AccessingCPU
SUPPORT BRACKETS
(BOTH SIDES)
LOOSEN 1/4 TURN ON
BOTH SIDES
REMOVE
REMOVE
g.7.2 g.7.3
WALL NOT SHOWN FOR CLARITY
A
B
Q
B
AQ
g.6.1 g.6.2
Q
BOTH SIDES BOTH SIDES
Q
Q
g.7.1
BOTH SIDES
Q
USE TOP HOLE
WHEN NOT USING
DEDICATED TILT
TOP HOLE
Table des matières
Autres manuels peerless-AV Support et étagère
peerless-AV
peerless-AV MOD-FW2KIT300 Manuel utilisateur
peerless-AV
peerless-AV DS-VW765-LQR Manuel utilisateur
peerless-AV
peerless-AV ACC170 Manuel utilisateur
peerless-AV
peerless-AV ACC 050 Manuel utilisateur
peerless-AV
peerless-AV DST995 Manuel d'instructions
peerless-AV
peerless-AV LCT100S Mode d’emploi
peerless-AV
peerless-AV IM746P Manuel utilisateur
peerless-AV
peerless-AV WBK100 Mode d’emploi
peerless-AV
peerless-AV FPS-1000 Manuel utilisateur
peerless-AV
peerless-AV TVA775 Manuel utilisateur
peerless-AV
peerless-AV DS-VWC555-3x2 Mode d’emploi
peerless-AV
peerless-AV ST650-AB Manuel utilisateur
peerless-AV
peerless-AV Mobile Videowall Trolley PDVWM 3x3 46 55 L Mode d’emploi
peerless-AV
peerless-AV ACC-CSH2 Manuel utilisateur
peerless-AV
peerless-AV LCH-100 Mode d’emploi
peerless-AV
peerless-AV SUA737 Mode d’emploi
peerless-AV
peerless-AV MIS-ACC201 Mode d’emploi
peerless-AV
peerless-AV SP840 Manuel utilisateur
peerless-AV
peerless-AV DS-VW775-QR Manuel utilisateur
peerless-AV
peerless-AV SEAMLESS Kitted 27BDL6119L/00 Manuel utilisateur
Manuels Support et étagère populaires d'autres marques
Salamander
Salamander Acadia AC/W/L400/WH Manuel utilisateur
Fohhn
Fohhn VAT-09 Guide de l'utilisateur
ricoo
ricoo FS0522 Manuel utilisateur
AMSOIL
AMSOIL BMK-22 Guide rapide
Kargo Master
Kargo Master 48220 Manuel utilisateur
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur
