Patton electronics 3087 Manuel utilisateur

ipRocketLink™ Model 3087

Serial G.SHDSL Bridge/Router

Quick Start Guide

Important

—This is a Class A device and is intended for use in a light industrial environment. It is not

intended nor approved for use in an industrial or residential environment.

Part Number: 07M3087-QS, Rev. C

Revised: February 15, 2012

Sales Office: +1 (301) 975-1000

Technical Support: +1 (301) 975-1007

E-mail: support@patton.com

WWW: www.patton.com

2Model 3087 Quick Start Guide

1.0 Power up the Bridge/Router

Your ipRocketLink comes with one of the following power supply options:

•

Internal AC powqer supply with detachable power cord

•

External AC adapter with detachable power cord

1.1 Models with internal AC power supply

1. Insert the female end of the AC power cord into the internal power supply connector.

2. Connect the male end of the power cord into an AC power outlet (100–240 VAC).

1.2 Models with external AC adaptor

1. Connect female plug of the AC power cord to the AC adaptor provided.

2. Connect the barrel-type connector of the AC adaptor to the barrel-type power jack on the ipRocketLink.

• This device contains no user serviceable parts. The equipment shall be

returned to Patton Electronics for repairs, or repaired by qualified

service personnel.

• Mains Voltage: Do not open the case the when the power cord is

attached. Line voltages are present within the power supply when

the power cords are connected. The mains outlet that is utilized to

power the devise shall be within 10 feet (3 meters) of the device,

shall be easily accessible, and protected by a circuit breaker.

• For AC powered units, ensure that the power cable used meets all

applicable standards for the country in which it is to be installed, and

that it is connected to a wall outlet which has earth ground.

• For units with an external power adapter, the adapter shall be a

listed Limited Power Source.

• Hazardous network voltages are present in WAN ports regardless of

whether power to the unit is ON or OFF. To avoid electric shock, use

caution when near WAN ports. When detaching the cables, detach the

end away from the device first.

• Do not work on the system or connect or disconnect cables during

periods of lightning activity.

The interconnecting cables shall be acceptable for external use and shall be rated for

the proper application with respect to voltage, current, anticipated temperature, flam-

mability, and mechanical serviceability.

WARNING

CAUTION

Model 3087 Quick Start Guide 3

3. Insert the male plug of the AC power cord into an AC power outlet (100–240 VAC)

1.3 Power-up indication

The Power LED blinks as the ipRocketLink is powering up. When the Power LED stops blinking and remains lit,

the ipRocketLink is ready for you to configure.

2.0 Configure the IP address

The ipRocketLink is shipped with a factory-configured IP address assigned to the Ethernet LAN port (green out-

line). The address is 192.168.200.10/24. In most cases, you must change the address to be on the same subnet

as your PC, as described in the procedures below. If you are not sure which IP address to use for your installa-

tion, contact your network administrator.

2.1 Connect a PC and log in

1. Using the included combination RS232/Ethernet cable and DB9-RJ45 adapter, connect a PC’s serial port

to the ipRocketLink’s Console port (see figure 1).

Figure 1. Connecting ipRocketLink to the PC’s serial port

2. Start a HyperTerminal session on the PC using the settings:

9600 bps, 8 data bits, 1 stop bit, no parity, no flow control

3. Log in to the ipRocketLink using the factory-default login and password:

Password: superuser

2.2 Modify the IP address

1. Display current IP interface settings for the ipRocketLink Ethernet LAN port.

ﬁ

ip list interfaces <enter>

Connect to Console port

Serial port

PC with

terminal emulator

Power

Console

ipRocketLink

G.SHDSL Integrated Access Device

Model 3086

Link

CTS

DTR

WAN Sync Serial

Link

100M

TxRx

Ethernet

Status

- 511E

- Normal

- 511

Test Modes

Local -

Normal -

Remote -

4Model 3087 Quick Start Guide

IP Interfaces:

ID | Name | IP Address | DHCP | Transport

---|------|----------------|----------|--------------

1 | ip1 | 192.168.200.10 | disabled | <bridge>

----------------------------------------------------

2. Modify the IP address for the LAN port according to your network requirements.

ﬁ

ip set interface ip1 ipaddress 10.10.10.5 255.255.255.0

Note The above IP address (

10.10.10.5/24)

is only an example. You must choose an IP address on the same

subnet as your PC.

3. Verify the new address is correct and save it in system boot memory.

ﬁ

ip list interfaces <enter>

ﬁ

system config save <enter>

ﬁ

3.0 Connect to the local IP network

Now you can connect the ipRocketLink to your local IP network and complete the remaining configuration from

your PC using a standard web browser.

Connect the ipRocketLink’s Ethernet port (green) to the same Ethernet segment as your PC (see figure 2). The

front-panel Ethernet Link LED should turn on. If it does not, press the rear-panel MDI-X switch so that the Ethernet

Link LED illuminates.

You can check the connection with the ping command. For example shown in figure 2, you would ping

10.10.10.5 from a PC on the IP network.

Figure 2. Connecting the ipRocketLink to the local IP network

Crossover

10/100

Ethernet DSL

Power MDI-X

Connect to Ethernet port

Ethernet port

MDI-X switch

Interface Port

Model 3087 Quick Start Guide 5

4.0 Log onto the web management interface

You will now access the web management graphical user interface (GUI) to configure the ipRocketLink using a

standard web browser (such as Internet Explorer or Netscape browser).

1. At your PC, open a web browser and enter the IP address you assigned to the ipRocketLink’s Ethernet LAN

port in step 2 of section 2.2 “Modify the IP address” on page 3.

2. Log in to the web management home page using the username superuser and the password superuser.

Figure 3. Model 3087 web management home page

5.0 Connect the G.SHDSL Port

1. Obtain single-twisted-pair cable with an RJ-11 plug connector at each end.

2. Plug one end of the cable into the (yellow) RJ-11socket (labelled DSL) on the ipRocketLink Integrated

Access Device.

3. Plug the other end of the cable into the RJ-11 wall socket that provides your G.SHDSL service.

4. When a DSL link is established the front-panel WAN LINK LED will turn on.

6.0 Connect the serial port

Your ipRocketLink is equipped with one of the following serial WAN ports for connection to an NTU:

•

V.35 (M/34 or DB-25)—Model 3087/RIC/EUI

•

X.21 (DB-15)—Model 3087/RID/EUI

•

T1/E1(RJ-48C and dual BNC)—Model 3087/RIC/EUI

6Model 3087 Quick Start Guide

Connect the serial cable to the ipRocketLink serial port as follows:

1. Attach the male connector of the serial cable to the female serial connector on the IAD.

2. Attach the other end of the cable to the serial connector on local serial NTU.

Note The 3087’s V.35 interface is wired as a DCE. No DTE configuration is possible. If you are directly con-

necting the 3087’s V.35 interface to a third-party equipment that cannot be configured as a DTE, you

must use a tail-circuit cable. You can purchase a tail-circuit cable from a datacom-supply vendor. A tail-

circuit cable will cross-over the necessary V.35 signals so that the two DCE interfaces can communicate.

Note The 3087’s X.21 interface is default configured as a DCE. Changing the DTE/DCE strap internally can set

the configuration for DTE. The 3087’s X.21 interface requires a cable with a male DB-15 connector.

7.0 Additional Information

For detailed information about configuring and operating guidance, set up procedures, and troubleshooting,

refer to the ipRocketLink 3086 User Guide available online at www.patton.com/manuals/3086.pdf.

A.0 Customer and Technical Support

Toll-Free VoIP support: call sip:suppo[email protected] with a VoIP SIP phone

Online support: www.patton.com

E-mail support: suppor[email protected]—answered within 1 business day

Telephone support:

•

Standard: +1 (301) 975-1007 (USA), Monday–Friday: 8:00 am to 5:00 pm EST (1300 to

2200 UTC/GMT)

•

Alternate: +41 (0)31 985 25 55 (Switzerland), Monday–Friday: 8:00 am to 5:00 pm CET (0900 to 1800

UTC/GMT)

Fax: +1 (253) 663-5693 (USA) or +41 (0)31 985 25 26 (Switzerland)

Model 3087 Quick Start Guide 7

B.0 Key factory default parameters

Key factory default parameters:

C.0 Compliance Information

C.1 Compliance

EMC:

•

FCC Part 15, Class A

•

EN55022, Class A

•

EN55024

Safety:

•

UL60950-1/CSA C22.2 No. 60950-1

•

IEC/EN 60950-1

•

AS/NZS 60950-1

PSTN Regulatory:

•

FCC Part 68

•

CS-03

•

AS/ACIF S043

8Model 3087 Quick Start Guide

C.2 Radio and TV Interference (FCC Part 15)

This equipment generates and uses radio frequency energy, and if not installed and used properly—that is, in

strict accordance with the manufacturer's instructions—may cause interference to radio and television recep-

tion. This equipment has been tested and found to comply with the limits for a Class A computing device in accor-

dance with the specifications in Subpart B of Part 15 of FCC rules, which are designed to provide reasonable

protection from such interference in a commercial installation. However, there is no guarantee that interference

will not occur in a particular installation. If the equipment causes interference to radio or television reception,

which can be determined by disconnecting the cables, try to correct the interference by one or more of the fol-

lowing measures: moving the computing equipment away from the receiver, re-orienting the receiving antenna,

and/or plugging the receiving equipment into a different AC outlet (such that the computing equipment and

receiver are on different branches).

C.3 CE Declaration of Conformity

Product Description: ipRocketLink 3087

We certify that the apparatus identified in this document conforms to the requirements of Council Directive

1999/5/EC on the approximation of the laws of the member states relating to Radio and Telecommunication

Terminal Equipment and the mutual recognition of their conformity.

The safety advice in the documentation accompanying this product shall be obeyed. The conformity to the above

directive is indicated by the CE sign on the device.

The signed Declaration of Conformity can be downloaded from www.patton.com/certifications/.

C.4 Authorized European Representative

D R M Green

European Compliance Services Limited.

Avalon House, Marcham Road

Abingdon,

Oxon OX14 1UD, UK

C.5 FCC Part 68 (ACTA) Statement

This equipment complies with Part 68 of FCC rules and the requirements adopted by ACTA. On the bottom side of

this equipment is a label that contains—among other information—a product identifier in the format US:

AAAEQ##TXXXX. If requested, this number must be provided to the telephone company.

The method used to connect this equipment to the premises wiring and telephone network must comply with the

applicable FCC Part 68 rules and requirements adopted by the ACTA.

If this equipment causes harm to the telephone network, the telephone company will notify you in advance that

temporary discontinuance of service may be required. But if advance notice isn’t practical, the telephone com-

The safety advises in the documentation accompanying the products shall be obeyed. The

conformity to the above directive is indicated by the CE sign on the device.

Model 3087 Quick Start Guide 9

pany will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with

the FCC if you believe it is necessary.

The telephone company may make changes in its facilities, equipment, operations or procedures that could

affect the operation of the equipment. If this happens, the telephone company will provide advance notice in

order for you to make necessary modifications to maintain uninterrupted service.

If trouble is experienced with this equipment, for repair or warranty information, please contact our company. If

the equipment is causing harm to the telephone network, the telephone company may request that you discon-

nect the equipment until the problem is resolved.

Connection to party line service is subject to state tariffs. Contact the state public utility commission, public ser-

vice commission or corporation commission for information.

C.6 Industry Canada Notice

This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is con-

firmed by the registration number. The abbreviation, IC, before the registration number signifies that registra-

tion was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications

were met. It does not imply that Industry Canada approved the equipment.

This Declaration of Conformity means that the equipment meets certain telecommunications network protective,

operational and safety requirements. The Department does not guarantee the equipment will operate to the

user's satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to

the facilities of the local telecommunications company. The equipment must also be installed using an acceptable

method of connection. In some cases, the company's inside wiring associated with a single line individual service

may be extended by means of a certified connector assembly (telephone extension cord). The customer should

be aware that compliance with the above condition may not prevent degradation of service in some situations.

Repairs to some certified equipment should be made by an authorized maintenance facility designated by the

supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give

the telecommunications company cause to request the user to disconnect the equipment. Users should ensure for

their own protection that the ground connections of the power utility, telephone lines and internal metallic water

pipe system, are connected together. This protection may be particularly important in rural areas.

10 Model 3087 Quick Start Guide

The information in this document is subject to change without notice. Patton Electronics assumes no

liability for errors that may appear in this document.

Trademarks statement

The term ipRocketLink is a trademark of Patton Electronics Company. All other trademarks presented in this doc-

ument are the property of their respective owners.

Warranty, Trademark, & Compliance Information

For warranty, trademark and compliance information, refer to the ipRocketLink 3086 User Guide located online

at www.patton.com/manuals.

In accordance with the requirements of council directive 2002/96/EC on Waste of

Electrical and Electronic Equipment (WEEE), ensure that at end-of-life you separate

this product from other waste and scrap and deliver to the WEEE collection system in

your country for recycling.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Patton electronics Routeur réseau

Patton electronics

Patton electronics SMARTNODE 4900 Manuel utilisateur

Patton electronics

Patton electronics PASSERELLES ROUTEURS VOIP 455X Guide de configuration

Patton electronics

Patton electronics ENVIRONET EHA3201 Manuel utilisateur

Patton electronics

Patton electronics SMARTNODE 4110 Series Manuel utilisateur

Patton electronics

Patton electronics 4520 Manuel utilisateur

Patton electronics

Patton electronics ONSITE 2603 Manuel utilisateur

Patton electronics

Patton electronics SmartNode 4900 Series Manuel utilisateur

Patton electronics

Patton electronics 2124 Manuel utilisateur

Patton electronics

Patton electronics 4630 Series Manuel utilisateur

Patton electronics

Patton electronics OnSite 3210 Series Manuel utilisateur

Patton electronics

Patton electronics SmartNode 5200 Manuel utilisateur

Patton electronics

Patton electronics SmartNode 4960 Series Manuel utilisateur

Patton electronics

Patton electronics SmartNode 4830 Series Manuel utilisateur

Patton electronics

Patton electronics IPLink 2821 Manuel utilisateur

Patton electronics

Patton electronics DIAMONDLINK 3201 Manuel utilisateur

Patton electronics

Patton electronics 2112 Manuel utilisateur

Patton electronics

Patton electronics SMARTNODE 4552 Manuel utilisateur

Patton electronics

Patton electronics SMARTNODE 4630 Series Manuel utilisateur

Patton electronics

Patton electronics DIAMONDLINK 3201 Manuel utilisateur

Patton electronics

Patton electronics 2121 Manuel utilisateur

Patton electronics

Patton electronics IPLink 2823 Manuel utilisateur

Patton electronics

Patton electronics 3224 Diamond Edge Manuel utilisateur

Patton electronics

Patton electronics SmartNode 4520 Series Manuel utilisateur

Patton electronics

Patton electronics IpLink 2884 Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité